Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"ford throwout bearing" Page 1 of 1

  • Speedway Chevy T-5 Transmission to Flathead Adapter Kit
    Speedway Chevy T-5 Transmission to Flathead Adapter Kit
    x
                

    Adapt GM/Chevy T-5 transmission to 1932-48 Ford or 1939-50 Mercury engines. Allows use of your early Ford clutch release shaft and fork.

    This Kit contains a Ford style throwout bearing that requires a Ford long style pressure plate (three finger). Such as Part #'s 9101565191015657, or 91015635

    Kit includes aluminum adapter, original Flathead style release bearing, throwout bearing return spring, adapter sleeves, and ball-bearing type pilot bearing.

    Installation Notes (PDF)

  • Ram Street Stock Hydraulic Throwout Bearing - Ford Tremac
    Ram Street Stock Hydraulic Throwout Bearing - Ford Tremac
    x
                

    Ram hydraulic bearings ease installations in vehicles with chassis constraints, and offer a smooth, lighter pedal effort.

    Kits contain the bearing, shims, fittings for AN# 3 connection, bleed line, and mounting hardware. A 3/4 inch bore master cylinder and AN 3 feed line are required for this installation. For 10-1/2" street stock type clutches. 

    This bearing comes with a new special machined front bearing retainer for the release bearing to ride on. 

    • The sleeve ID 1.379
    • The bearing OD 2.940
    • Length collapsed 2.192
    • Length extended 3.050
    • Stroke .853

    Learn more about hydraulic release bearings and how to properly install them by reading our tech article. How to Install a Hydraulic Throwout Bearing.

  • Ram Street Stock Hydraulic Throwout Bearing - Ford T-5
    Ram Street Stock Hydraulic Throwout Bearing - Ford T-5
    x
                

    Ram hydraulic bearings ease installations in vehicles with chassis constraints, and offer a smooth, lighter pedal effort.

    Kits contain the bearing, bleeder hose assembly, shims and mounting hardware. A 3/4 inch bore master cylinder and AN 3 feed line are required for this installation. For 10-1/2" street stock type clutches. 

    This bearing comes with a new special machined front bearing retainer for the release bearing to ride on.

    • The sleeve ID 1.385
    • The bearing OD 2.940
    • Length collapsed 2.174
    • Length extended 3.032
    • Stroke .867

    NOTE:  NOT meant for use with world class T-5 cases

    Learn more about hydraulic release bearings and how to properly install them by reading our tech article. How to Install a Hydraulic Throwout Bearing.

  • 1932-48 Ford Flathead Clutch Release Fork, 85, 90, and 95 HP Passenger Cars
    1932-48 Ford Flathead Clutch Release Fork, 85, 90, and 95 HP Passenger Cars
    x
                

    This is a replacement clutch fork that fits 1932-1948 Ford 85 & 95 horsepower motors.  It will also work for 1932-52 Ford Pickup applications.  These clutch forks are used to engage the throwout bearing. 

    • OEM replacement
    • 1932-48 Ford 85 & 95 HP motors
    • 1932-52 Ford Pickup
    • Used to engage throwout bearing

    Don't forget to include our clutch release shaft (91675100 or 91675101), and pin (91675151) with your clutch fork.

  • Quick Time RM-8010 Ford 400-429-460 Steel Bellhousing - T5 & TKO
    Quick Time RM-8010 Ford 400-429-460 Steel Bellhousing - T5 & TKO
    x
                

    These strong, lightweight steel bellhousings are just the ticket for installing a Borg-Warner T5 or Tremec TKO manual transmission behind your favorite V8 engine. We're now offering them for big block Ford 400, 429 and 460.

    The compact design allows the bellhousings to fit in tight quarters and most will accommodate up to a 10-1/2" clutch. Set up to use an original style clutch fork and release bearing, but can also be used with hyraulic release bearings.  

    Drilled for most major throwout bearings. Includes lower flywheel cover.

    •      Height = 7.050
    •      Trans. Bore Ø = Universal 4.910/4.685
    •      Engine = Ford 351m, 400, 429, 460
    •      Trans. = Universal Ford TKO 500-600/T5 Mustang/TR3550
    •      Clutch Ø = 12"
    •      Flywheel = 176 tooth
    •      Weight = 22#
    •      Universal fork brackets for diaphragm or cable linkage
    •      Has passed all SFI testing
    •      Pivot ball, fork brackets, grade 8 bolts, and full engine plate included
  • Quick Time RM-8011 Big Block Ford Steel Bellhousing, T10 & Toploader
    Quick Time RM-8011 Big Block Ford Steel Bellhousing, T10 & Toploader
    x
                

    These strong, lightweight steel bellhousings are just the ticket for installing a Borg-Warner T10 or Toploader 4-speed manual transmission behind your favorite V8 engine. We're now offering them for big block Ford 400, 429 and 460.

    The compact design allows the bellhousings to fit in tight quarters and most will accommodate up[ to a 10-1/2" clutch. Set up to use an original style clutch fork and release bearing, but can also be used with hydraulic release bearings.  

    Drilled for most major throwout bearings. Includes lower flywheel cover.

    •     Height = 6.300
    •      Trans. Bore Ø = Universal 4.85/4.910/4.685
    •      Engine = Ford 351m, 400, 429, 460
    •      Trans. = Universal Toploader/Borgwarner T-10/Short Shaft Ford TKO 500-600
    •      Clutch Ø = 12"
    •      Flywheel = 176 tooth
    •      Weight = 22#
    •      Universal fork brackets for diaphragm or cable linkage
    •      Has passed all SFI testing
    •      Pivot ball, fork brackets, grade 8 bolts, and full engine plate included
  • Quick Time RM-6060 Ford 289-351W Steel Bellhousing - T5
    Quick Time RM-6060 Ford 289-351W Steel Bellhousing - T5
    x
                

    These strong, lightweight steel bellhousings are just the ticket for installing a manual transmission behind your favorite V8 engine. We're now offering them for small block Fords with 157 tooth flywheels.

    The compact design allows the bellhousings to fit in tight quarters. These steel bellhousings were designed to be as small as possible to allow more room in the transmission tunnel and firewall area. Will accommodate up to a 10-1/2" clutch. Set up to use an original style clutch fork and release bearing. Can also be used with hyraulic release bearings.  

    Drilled for most major throwout bearings. Includes lower flywheel cover.

     

  • Ram Clutches 497 Ford Transmission Manual Release Bearing, Triple Disc
    Ram Clutches 497 Ford Transmission Manual Release Bearing, Triple Disc
    x
                

    Repair throwout bearing for Ram oval track "assault" racing clutch.

    Tech Tip:  When installing a new clutch, be sure to follow the manufacturer's instructions for correct set-up.  You should also replace the pilot bushing/bearing.

    Tech Tip:  To extend the life of your expensive racing clutch you should not use it to load the car on or in your trailer.  The amount of slippage this causes is worse than a night of racing.

     

  • Offenhauser 5272 GM Manual Trans to Flathead V8 Adapter, Ford Clutch
    Offenhauser 5272 GM Manual Trans to Flathead V8 Adapter, Ford Clutch
    x
                

    Get more performance and driveability out of your Ford Flathead V8 by hooking it up to a GM manual transmission! This adapter allows you to easily install a GM 3-, 4-, or even 5-speed transmission behind your 1932-1948 Ford or 1939-1950 Mercury Flathead V8 engine.

    Permits use of your Ford clutch release shaft, fork and throwout bearing. Throwout bearing must be used with a Long-style pressure plate.

    560-5272 Instructions (PDF)

    Installation Notes (PDF) 

  • Flathead to GM Trans Bearing & Arm Kit
    Flathead to GM Trans Bearing & Arm Kit
    x
                

    Throwout bearing and clutch fork kit for GM transmission to Flathead adapters 560-5174 and 916-28914.

    Must be used with a Diaphragm-style pressure plate.

    916-29510 Instructions (PDF)

  • Racing Clutch Hydraulic Throwout Bearing
    $99.99
    $119.99
    Racing Clutch Hydraulic Throwout Bearing
    x
                

    Ultra lightweight clutch release bearing for Chevy or Ford transmissions. Installs by simply removing two of the bearing retainer bolts and replacing them with the provided studs. Use 3/4" bore master cylinder.

    Works with the following clutches:

    • Tilton 2-disc or 3-disc (7.25" and 5.5")
    • Quartermaster 2-disc or 3-disc (7.25" and 5.5")
    • Ram Assault 2-disc or 3-disc (1996 and newer)

    910-25602 Instructions (PDF)

    NOTE: Will not work with stock-style clutches or Ram Couplers.

    Learn more about hydraulic release bearings and how to properly install them by reading our tech article. How to Install a Hydraulic Throwout Bearing.

  • Howe Racing 82876 GM T-5 Stock Clutch Hydraulic Throwout Bearing
    Howe Racing 82876 GM T-5 Stock Clutch Hydraulic Throwout Bearing
    x
                Please view the product's page for more information
            
  • Speedway GM Manual Trans to Flathead V8 Adapter, Ford Clutch
    Speedway GM Manual Trans to Flathead V8 Adapter, Ford Clutch
    x
                

    Get more performance and driveability out of your Ford Flathead V8 by hooking it up to a GM manual transmission! This adapter allows you to easily install a GM 3-, 4-, or even 5-speed transmission behind your 1932-1948 Ford or 1939-1950 Mercury Flathead V8 engine.

    Permits use of your Ford clutch release shaft, fork and throwout bearing. Throwout bearing must be used with a Long-style pressure plate. Adapter kit includes pilot bushing.

    916-28912 Instructions (PDF) 

    Installation Notes (PDF) 

  • Ram Clutches 78160 Retrofit T-56 Hydraulic Bearing Kit
    Ram Clutches 78160 Retrofit T-56 Hydraulic Bearing Kit
    x
                

    The T-56 bearing is designed for use in retrofit or custom applications with GM engines.  Early engine applications require a transmission spacer with the T-56.  Check with your transmission supplier.  This kit contains all mounting hardware, fittings and remote bleeder.  This bearing requires a 3/4 inch master cylinder. 

    • Retrofit or custom GM engine applications
    • Early engines require transmission spacer
    • Contains all hardware, fittings and remote bleeder
    • Requires 3/4 inch master cylinder
    WARNING:  A person has to be careful to purchase the right parts for this. Not all T-56 use the same parts.  Ford and GM are different, LT and LS are different.

    Learn more about hydraulic release bearings and how to properly install them by reading our tech article. How to Install a Hydraulic Throwout Bearing.

  • 2.3 Ford Release Bearing
    $29.99
    2.3 Ford Release Bearing
    x
                

    Clutch release (throwout) bearing for your 2.3 Ford race motor.

  • Bushing and Throw Out Bearing - GM Trans to Flathead
    Bushing and Throw Out Bearing - GM Trans to Flathead
    x
                

    Bushing and throwout bearing kit for GM transmission to Flathead adapters 560-5272 and 916-28912.

    Must be used with a Long-style pressure plate.

    916-29500 Instructions (PDF)

  • Garage Sale - Ram 486 Ealy Ford 1-3/8 Clip Style Clutch Release Bearing
    Garage Sale
    Garage Sale - Ram 486 Ealy Ford 1-3/8 Clip Style Clutch Release Bearing
    x
                

    RAM uses only the highest quality materials in the construction of their throwout bearings. These have an 1-3/8" shaft diameter hole clip style bearing.

     

    This is garage sale priced because it has been discontinued.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

  • Garage Sale - GM Stock Clutch Hydraulic Throwout Bearing
    Garage Sale
    Garage Sale - GM Stock Clutch Hydraulic Throwout Bearing
    x
                Please view the product's page for more information
            
  • Garage Sale - Ram Street Stock Hydraulic Throwout Bearing - Ford T-5
    Garage Sale
    Garage Sale - Ram Street Stock Hydraulic Throwout Bearing - Ford T-5
    x
                Please view the product's page for more information
            
  • Tilton 5-1/2 Inch Low Ground Clearance Package With Belt Drive
    Tilton 5-1/2 Inch Low Ground Clearance Package With Belt Drive
    x
                

    Lightweight steel bell housing that has provision for dry sump pump or fuel/power steering pumps to be mounted on it.  Includes 5-1/2" 3 disk clutch and flywheel, hydraulic throwout bearing, HTD belt, drive pulley and pressure plate mounted pulley,  reverse rotation starter, hoses and fittings. This package will work on small block Ford with Muncie or Saginaw transmissions.  Pumps are not included, but this kit will work with 5/8" keyway pumps.

     This package has been only been opened for pictures.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS