Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Brand Banners -  Ford Racing
Searched For:

"ford racing 3" Page 1 of 11

  • Ford Racing M-6880-A50 90 Degree Oil Filter Adapter
    Ford Racing M-6880-A50 90 Degree Oil Filter Adapter
    x
                

    There are times you just don't have room for the oil filter on your Ford powered toy. This adapter attaches where the oil filter mounts and turns the filter 90 degrees. Rotate filter toward front of engine to provide clearance for engine swaps and chassis modifications.

    Fits most Ford V8 and some 4 cyl. engines that use Fram PH8A/HP1 or Motorcraft FL-1A oil filters. 

  • Professional Products 81008 S/B Ford Balancer Pulley Spacer, 7/8 Inch
    Professional Products 81008 S/B Ford Balancer Pulley Spacer, 7/8 Inch
    x
                

    This spacer must be used when replacing an original balancer that is 3-7/8" long which were typically found on '80 and earlier 351W Ford racing HO engines or '80 and later 351W, 302, or 5.0L engines using the Ford Racing .917" crank sprocket.

    Harmonic Balancer Technical Notes (PDF)

  • Speedway Aluminum Extruded Leaf Spring Lowering Blocks
    Speedway Aluminum Extruded Leaf Spring Lowering Blocks
    x
                

    Our lightweight extruded aluminum lowering blocks are stronger than billet!  Available in several heights, all 2-1/2" wide, 5" long.  The centering pin is 9/16".  These blocks will increase or decrease suspension height on most leaf spring applications and can be installed below the leaf spring to raise the vehicle or on top of the leaf spring to lower the vehicle. These lowering blocks allow you to lower your leaf spring vehicle by up to 4 inches.  Heavy Duty U-bolts and hardware are available separately.

    • Lightweight aluminum lowering blocks are stronger than billet
    • 2-1/2" wide
    • 5" long
    • 9/16" centering pin
    • Increase or decrease suspension height on most leaf spring applications
    • Allows you to lower your leaf spring vehicle by up to 4 inches
    • U-bolts and hardware available separately

    Lowering blocks are sold individually (each).

    THICKNESS options explained:

    • 025 = 1/4" thick
    • 050 = 1/2" thick
    • 075 = 3/4" thick
    • 100 = 1" thick
    • 150 = 1.5" thick
    • 200 = 2" thick
    • 250 = 2.5" thick
    • 300 = 3" thick
    • 350 = 3.5" thick
    • 400 = 4" thick
  • Hastings Rings SWY5075125 Flathead Ford 3-Ring Piston Set, 3.3125 Bore
    Hastings Rings SWY5075125 Flathead Ford 3-Ring Piston Set, 3.3125 Bore
    x
                

    Hastings is the ring of choice for your vintage flathead Ford V-8. We have these premium 3-ring sets with 5/64" cast top, 5/64" cast second, and 3/16" chrome-edge oil ring. 

    Each ring set includes all rings for (8) pistons.

  • 2.3 Ford 7-3/4 Inch Racing Clutch Disc-Metallic
    2.3 Ford 7-3/4 Inch Racing Clutch Disc-Metallic
    x
                2.33 lbs, Metallic clutch disc - solid hub for a 7-3/4" 2.3 Ford racing clutch.  1"-23 Spline
            
  • Canton Racing 11-900 2.3 Ford Engine Saver Rear Sump Oil Pan, Stock
    Canton Racing 11-900 2.3 Ford Engine Saver Rear Sump Oil Pan, Stock
    x
                

    It doesn't matter whether you have a bone stock engine or a 500 HP killer. If the oil system isn't up to task, it's trashed! Don't put a cheap oil pan on any engine! These Canton Racing oil pans feature anti-slosh baffling, trap doors, crank scraper, and a magnetic drain plug. 

    This Circle Track stock appearing rear sump is for ‘74-`97 2300cc OHC Ford engines. It is stock depth with a 5 quart system capacity. Stock dimensions are capacity are retained, but Canton's specially designed baffling system ensures increased oil control.  Magnetic drain plug.

    • 7" Deep
    • 7-3/4" Wide


  • Fel-Pro Gaskets FS7525B 1949-53 Flathead Ford V8 Overhaul Gasket Set
    Fel-Pro Gaskets FS7525B 1949-53 Flathead Ford V8 Overhaul Gasket Set
    x
                

    If you're going to overhaul your Flathead, you're going to need new gaskets. This complete overhaul gasket set is for 1949-1953 Ford and Mercury flathead V8 engines. Includes all the necessary gaskets and seals you need for a typical engine rebuild.

    • High-quality gaskets for a leak-free engine
    • Modern composition head gaskets
    • Head gaskets will fit bores up to 3-3/16" (3.270")
    • Set includes gaskets for:
      • Cylinder Heads
      • Oil Pan
      • Rear Seal
      • Water Pumps
      • Front Packing
      • Fuel Pump
      • Water Necks
      • Timing Cover
      • Valve Seals
      • Intake Manifold
      • Exhaust Manifolds
  • Holley 12-289-13 S/B Ford Racing Pro Mechanical Fuel Pump, 130 GHP
    Holley 12-289-13 S/B Ford Racing Pro Mechanical Fuel Pump, 130 GHP
    x
                

    If you are looking for a high flow fuel pump you can depend on night after night, this is it! Holley's high output, heavy duty mechanical fuel pumps are constructed of rugged materials and feature fuel body castings that can be rotated to accommodate various plumbing situations. 3/8" NPT inlet and outlet.

    • High output fuel flow
    • Heavy duty construction for continuous high RPM performance
    • Six high flow valves ensure adequate and continuous fuel flow
    • Beefy steel rocker arm to help withstand race usage
    • Inlet & outlet tapped for 3/8" NPT

    For Carbureted Ford 289/302/351W V8s running gasoline only. NOT for use with alcohol.

    Holley Pump Tech Info (PDF)

  • Ram Clutches 8355 7.25 Inch Stock Car 3-Disc Clutch, Small Block Ford
    Ram Clutches 8355 7.25 Inch Stock Car 3-Disc Clutch, Small Block Ford
    x
                

    Ram has put their extensive knowledge to work developing this extremely durable 7-1/4" clutch. The four paddle multi disc clutch design has twice the friction material of other 7-1/4" clutch units and features a proprietary friction material known for its outstanding durability. The Ram 7-1/4 will also bolt directly to most existing 7-1/4" flywheels.

    Multi-Disc Features:  

    • New internal drive mechanism provides smooth, driveable engagement
    • Twice the friction material of other 7.25" clutches
    • Proprietary Ram friction mix known for outstanding durability
    • Discs feature 8 rivet hubs for added torque capacity
    • Bolts directly to existing 7.25" flywheels
    • 3-disc Clutch: 9.7 lbs (weight without the button)

    Tech Tip:  When installing a new multi disc clutch, be sure to follow the manufacturer's instructions for correct set-up.  You should also replace the pilot bushing/bearing.

    Tech Tip:  To extend the life of your expensive racing clutch you should not use it to load the car on or in your trailer.  The amount of slippage this causes is worse than a night of racing.

     

  • Best Gasket 536G-P 49-53 Flathead Ford GraphTite Big Bore Head Gaskets
    Best Gasket 536G-P 49-53 Flathead Ford GraphTite Big Bore Head Gaskets
    x
                

    These 1949-1953 Flathead Ford Head gaskets are for use with all bores from 3-1/16" to 3-3/8".

    • 1949-1953 Flathead Fords
    • GraphTite cylinder head gaskets
    • Use with all bores from 3-1/16" to 3-3/8"

    Note: Please use a spray-on sealer like K&W Copper Coat or Permatex Copper Spray-a-Gasket when installing these head gaskets. Be sure to re-torque the bolts/nuts after several warm-up/cool-down cycles.

  • IMCA 1978-88 GM Metric Chassis 9 Inch Ford Axle Bracket Kit
    IMCA 1978-88 GM Metric Chassis 9 Inch Ford Axle Bracket Kit
    x
                

    You can weld these brackets to your 9" Ford housing and install it in your 1978-88 GM Metric chassis. Includes upper and lower control arm mounts. Welding required. Designed for 3-1/2" axle tubes, but can be fit to 3" tubes.

  • 2.3 Ford 7-3/4 Inch Racing Pressure Plate
    2.3 Ford 7-3/4 Inch Racing Pressure Plate
    x
                

    This stock appearing 7-3/4" pressure plate is the lightest on the market for the 2300 Ford engine. Less rotating weight means faster acceleration off the corners. 1"-23 spline.

  • Offenhauser 1939-53 Flathead Ford 4-Ring Pistons, 3.75 Stroke, 3.248 Bore
    Offenhauser 1939-53 Flathead Ford 4-Ring Pistons, 3.75 Stroke, 3.248 Bore
    x
                

    Original Flathead pistons used four rings, were somewhat round, had questionable wrist pins and locks and were made of cast iron. These pressure-cast aluminum pistons share the four-ring design, but are cam ground and use modern steel wrist pins and real snap rings. They’re a great upgrade when rebuilding your 1939-1953 flathead Ford or Mercury V8 engine.

    The original bore size was 3.188", which makes these .060" oversize. Sold in sets of eight.

    • Original 4-ring design
    • Pressure cast aluminum construction provides great strength and durability
    • Precision cam ground
    • Modern steel wrist pins
    • Snap ring style retainer clips
  • Master Cylinder/Pedal Assembly for Model T, A, 1932 Ford
    Master Cylinder/Pedal Assembly for Model T, A, 1932 Ford
    x
                

    Designed for a clean and simple install onto Model T, Model A, and 1932 Ford frame. The included 1" bore remanufactured master cylinder is suitable for 4-wheel disc or disc/drum brake setups. The outlet ports are 3/8"-24 IFF. The bracket can be bolted or welded to the left frame rail (boxed or stock).

    Kit includes a dual feed master cylinder, frame bracket, and a steel pedal arm w/ pad that can be easily modified for driver comfort.

    Note: Will NOT work in conjunction with the factory clutch pedal. Intended for use with an Automatic Transmission.

    916-31926 Instructions (PDF) 

    Learn more about selecting the proper master cylinder for your vehicle by reading our tech article. Brake System Selection. 

  • AFCO 3875R Eliminator Rear Shocks-Single Adj. 7 In Stroke-Ford/Mercury
    AFCO 3875R Eliminator Rear Shocks-Single Adj. 7 In Stroke-Ford/Mercury
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  Tie Bar Mount w/ 2.375" bolt centers
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    See Applications tab for Ford-Mercury chassis fittment.

     

  • AFCO 3870R Eliminator Rear Double Adj. Shock, 7 In Stroke-Ford/Mercury
    AFCO 3870R Eliminator Rear Double Adj. Shock, 7 In Stroke-Ford/Mercury
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Body Mount:  Tie Bar Mount w/ 2.375" bolt centers
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    See Applications tab for Ford-Mercury chassis fittment.

  • Ford 9 Inch Third Member Assembly, Mini Spool, 31-Spline
    Ford 9 Inch Third Member Assembly, Mini Spool, 31-Spline
    x
                
    • Profesionally assembled for oval track racing only 
    • Pro Gears ring & pinion
    • Your choice of gear ratio, 3.50:1 to 7.33:1
    • 31-spline premium mini spool
    • New chromoly cross pin
    • Viton high heat pinion seal
    • Solid pinion bearing spacer with shims
    • Includes 3-5/8"stock Ford yoke.

    910-48341 Instructions (PDF)

    Third members are made to order. Please allow 24-48 hours for order to ship.

    Available options include a yoke to accept 3 1/4" Chevy/GM U-joint (add 91048339) or lightening of the ring gear to remove weight (add 91600013; ratios 4.78, 5.25, 5.37, 5.50, 5.57, 6.14, 6.66, 6.83, 7.00, 7.16, and 7.33 are already lightened). The letter "l" behind a ratio also indicates the availability of a lightened ratio.

  • 1949-53 Flathead Car/Pickup Water Pump with Wide Belt
    1949-53 Flathead Car/Pickup Water Pump with Wide Belt
    x
                

    Original flathead water pumps have always suffered from unreliable bronze bushings and carbon seals. They almost always leaked and even Ford manuals warned mechanics not to tighten fan belts too tight. The excess slack allowed belts to slip and lose contact with the generator and water pump pulleys, causing more cooling and power problems.

    Speedway's completely new water pumps feature severe-duty roller and ball bearings, close tolerances and modular impellers to provide maximum flow and reduce cavitation. They also have modern ceramic seals on a heavy duty 3/4" shaft, making the assembly exceptionally strong and more efficient.

    Note: This water pump is for 1949-1953 engines in 1948-1952 pickups or 1932-1948 cars.

    • Flathead Water Pump Features (Link)
    • Designed for use with 5/8" belt drive system
    • Severe-duty roller and ball bearings
    • Ceramic seals on sturdy 3/4" shaft
    • High-flow modular impeller reduces cavitation
    • Includes gasket and a connection for the heater hose return

    1949-1953 Flathead Water Pump Installation Instructions (PDF)

  • Ford Racing 11 Inch Drum Brake Kit, 2-1/2 Offset
    Ford Racing 11 Inch Drum Brake Kit, 2-1/2 Offset
    x
                We offer these rear drum brake kits for popular 9" Ford rear axles. Each kit has new 11" x 2-1/4" drums, backing plates, shoes, wheel cylinders, springs, emergency brake arm and hardware.  

    Fits New style Big Ford housing with 2-1/2" axle offset and 3.15" axle bearing. Drums drilled for 5 on 4-1/2" bolt pattern.

    Axle Flange Identification Chart (Link)

  • AFCO 80103FN Universal Fit Racing Radiator, 26 Inch Ford/Mopar
    AFCO 80103FN Universal Fit Racing Radiator, 26 Inch Ford/Mopar
    x
                Please view the product's page for more information
            
  • Hastings Rings SWY5075188 Flathead Ford Piston 3-Ring Set, 3.375 Bore
    Hastings Rings SWY5075188 Flathead Ford Piston 3-Ring Set, 3.375 Bore
    x
                Hastings is the ring of choice for your vintage Flathead Ford V-8. We have these quality 3 ring sets with 5/64", 5/64", 3/16" ring grooves.  Set of 8.
            
  • Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
    Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
    x
                

    Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 56" from hub-to-hub.   The pumpkin is centered in the housing, which puts the pinion offset 2-3/8" from center

    Includes a set of Currie 31-spline heat-treated, forged alloy axle shafts. Wheel bolt patterns are dual drilled for 5 on 4 1/2" Ford and 5 on 4 3/4" Chevy, and an access hole is drilled. Axles come with a full installation package which includes one set of five 1/2"-20 Ford style wheel studs, one set of five 7/16"-20 Chevy style wheel studs, one set-20 tapered roller bearing with race, seal, & collar, and one heavy duty late model large bearing style retainer plate. Axle bearing does not come pressed onto the axle shaft, and wheel studs are not installed.

    Third member sold separately.

  • Low Rear Axle Bracket 5 3/4 Inch
    Low Rear Axle Bracket 5 3/4 Inch
    x
                All brackets are for 3" rear axle application.

    Low Rear Axle Bracket
    Mount radius rods lower than rear axle. 3/8" steel. 5-3/4" long. 3/8" holes.
  • 1935-1948 Ford/Mercury High Speed Ring and Pinion Gear Set, 3.54 Gear Ratio
    1935-1948 Ford/Mercury High Speed Ring and Pinion Gear Set, 3.54 Gear Ratio
    x
                

    These fit 1935-1948 passenger cars or 1935-1941 Ford 1/2 ton pick-ups (no 3/4 ton or larger). All gear sets are direct replacements for stock, non-quickchange rear axles. 6-spline input.

    • Fits 1935-48 Passenger Cars or 1935-41 Ford 1/2 ton pickups
    • Does not fit 3/4 ton or larger
    • Stock (non-quick change)
    • All gear sets are direct replacements
    • Six spline input
    • 3.54 gear ratio

    Installation Instructions  (PDF)

  • QA1 FC1957-3P GM/Ford Street Front Shock-EZ Up Right Front 7-3 Valving
    QA1 FC1957-3P GM/Ford Street Front Shock-EZ Up Right Front 7-3 Valving
    x
                Replace your old original shocks with new QA1 racing shocks and feel the difference! If your rules mandate a shock that uses stock mounting, QA1 is the shock for YOU! Finally get a racing shock that uses the latest technology with a stock mount!
    • Racer Revalveable and Rebuildable
    • No Valving Overlap
    • Precision Machined Piston with P.T.F.E. Piston Band
    • 15mm Centerless Ground, Hard Chrome Plated, Solid Piston Rod
    • Deflective Disc Valving
    • Twin Tube Design
    • 2" O.D. Steel Body
    • Use Large Body Tuning Kit # TK01 For Valve Combination Changes Between 0-13

    For GM full-size front and Ford mid-size & full-size front.

    QA1 Street Stock Application Chart (GIF)

    Note: Valving for these QA1 shocks is listed as COMPRESSION-REBOUND. Example: 7-3 means 7 COMPRESSION and 3 REBOUND. 7 means 7 COMPRESSION and 7 REBOUND.

  • Bendix Style Brakes for 1937-48 Ford Spindles, 12 x 2 Inch
    Bendix Style Brakes for 1937-48 Ford Spindles, 12 x 2 Inch
    x
                

    If you want the early look but are reluctant to use old non-energizing drum brakes, we have just what you need. Our 100% new self-energizing backing plate assemblies come complete with shoes, wheel cylinders and hardware. Fits either the front or rear of 1937-48 Ford cars or 1937-47 Ford half-ton pickups with original style rear axle.

    These brake assemblies can be used with Buick drums and 1948 Ford hubs, or we also offer new iron 12" x 2" brake drums (910-65400) with 5 on 5-1/2" bolt circle which are impossible to find elsewhere.

    Wheel Cylinder Inlet: 7/16"-20 straight thread
    NOT 7/16"-20 IFF
    Inlet fitting will require a sealing washer or O-ring style fitting
    Bolt Pattern: 3-3/8" center-to-center both horizontal and vertically
    If using Model A or B spindles the holes will have to be elongated inward to fit the narrower bolt pattern

    We recommend use of adapter rings 916-31928 to keep the spindle centered in the backing plate 

  • Isky Racing Cams 211100 Max-1 1932-48 Flathead Ford Camshaft
    Isky Racing Cams 211100 Max-1 1932-48 Flathead Ford Camshaft
    x
                

    Isky’s Max-1 is by far the best camshaft we have found for the vast majority of all flathead V8-powered street rods. It offers a great hot rod sound without sacrificing street manners, and provides good low-speed power with both stock and multi-carb intake manifolds.

    Cam Application Chart (GIF)

    450-211100 Specs (Link)

  • Ford Racing 302-001 Small Block Aluminum Valve Covers
    Ford Racing 302-001 Small Block Aluminum Valve Covers
    x
                

    Polished aluminum valve covers are 3-3/4" tall with black letters. Will clear stud girdle and roller rockers. One hole in each cover for a PCV or a breather. Grommets are supplied for both, as well as baffle plates to install inside the covers for oil control. Comes with instructions.

    • Style of hole: Push-in
    • Suggested bolt length: 1"
    • These valve covers have baffles
  • Basic Disc Brake Kit, 1969-77 GM Caliper, Stock Ford Spindle, 5on4-3/4
    Basic Disc Brake Kit, 1969-77 GM Caliper, Stock Ford Spindle, 5on4-3/4
    x
                

    This basic front disc brake conversion kit allows you to easily install '73-'77 GM mid-size 11" rotors (5 on 4-3/4") and '69-'77 mid-size GM single piston calipers onto your '37-'48 Ford passenger car style spindles. No machine work needed.

    Kit includes:

    • 1973-77 GM brake brackets
    • 1973-77 hardware
    • Bearing and seal adapters
    • Seals
    • Inner bearing cups
    • Inner bearing cones
    • Spacers
    • Instructions
    • Does not include dust caps, washers or spindle nuts
    Note: Not for use with bolt-on steering arms. The 11" rotor brake kits are great for street rods based on 1932-48 Fords. However these kits are much too large and heavy for a T-bucket or early roadster.

    916-31901 Instructions (PDf)

  • Bendix Style Emergency Brakes for 1937-48 Ford Rear, 12 x 1-3/4 Inch
    Bendix Style Emergency Brakes for 1937-48 Ford Rear, 12 x 1-3/4 Inch
    x
                

    If you want the early look but are reluctant to use old non-energizing drum brakes, we have just what you need. Our 100% new self-energizing backing plate assemblies come complete with shoes, wheel cylinders and hardware. Fits either the front or rear of 1937-48 Ford cars or 1937-47 Ford half-ton pickups with original style rear axle.

    These have provisions for an emergency brake cable. These brake assemblies can be used with Buick drums and 1948 Ford hubs, or we also offer new iron 12" x 2" brake drums (910-65400) with 5 on 5-1/2" bolt circle which are impossible to find elsewhere.

    • Wheel Cylinder Inlet:  7/16"-24 IFF
      • To connect an AN 3 hose, use (2) of 910-318-7/16"
      • To connect a 3/16" steel line, use (2) of 910-3183-7/16"
    • Bolt Pattern:  3-3/8" center to center both horizontal and vertically
    • Use with park brake cables typical of '39-'48 Ford passenger cars
  • Professional Products 81006 S/B Ford Balancer Pulley Spacer, 3/8 Inch
    Professional Products 81006 S/B Ford Balancer Pulley Spacer, 3/8 Inch
    x
                

    This spacer must be used when replacing an original balancer that is 3-3/8" long which were typically found on '79 and earlier 351W engines.

    Harmonic Balancer Technical Notes (PDF)

  • Speedway Weld-On Spring Pad for 3 Inch Axle Tube
    Speedway Weld-On Spring Pad for 3 Inch Axle Tube
    x
                

    These weld-on leaf spring pads fit 3" diameter axle tubes. Works with all 2-1/2" wide leaf springs.

  • Canton Racing 11-920 2.3 Ford Engine Oval Track Front Sump Oil Pan
    Canton Racing 11-920 2.3 Ford Engine Oval Track Front Sump Oil Pan
    x
                

    It doesn't matter whether you have a bone stock engine or a 500 HP killer. If the oil system isn't up to task, it's trashed! Don't put a cheap oil pan on any engine! These Canton Racing oil pans feature anti-slosh baffling, trap doors, crank scraper, and a magnetic drain plug. 

    This Ford left turn front sump is for ‘74-97 2300cc ohc engines in front sump Pinto chassis and mini-modifieds. It has a 7-1/2" Deep, 12" Wide, 9-1/2" Long sump that holds 5-1/2 quarts and has a 6 quart system capacity. This pan works with our 2300 main support when using a 86C pump and pan's crank scraper is modified for clearance.

    • 7-1/2" Deep
    • 12" Wide


  • Canton Racing 11-910 2.3 Ford Engine Rear Sump Oil Pan, Oval Track
    Canton Racing 11-910 2.3 Ford Engine Rear Sump Oil Pan, Oval Track
    x
                

    It doesn't matter whether you have a bone stock engine or a 500 HP killer. If the oil system isn't up to task, it's trashed! Don't put a cheap oil pan on any engine! These Canton Racing oil pans feature anti-slosh baffling, trap doors, crank scraper, and a magnetic drain plug. 

    This Ford left turn rear sump is for ‘74-97 2300cc ohc engines in Fox bodies, rear sump Pinto chassis, and mini-modifieds. It has a 7" deep, 11" wide, 8-1/2" long sump that holds 5 quarts and has a 5-1/2 quart system capacity. Pans will work with a stock starter. This pan works with our 2300 main support when using a 86C pump and pan's crank scraper is modified for clearance.

    • 7" Deep
    • 11" Wide


  • Ford 9 Inch with 4-Link Assembly for Speedway 32 Ford Frame
    Ford 9 Inch with 4-Link Assembly for Speedway 32 Ford Frame
    x
                

    Triangulated 4-link rear suspension kit, including a Ford 9" rear end, specifically for the Speedway '32 Ford Boxed Truss frame 916-57050. This kit is a true bolt-in into our '32 Ford frame - no welding required. We suggest QA1 Adjustable rear coilovers 721-485 (at right) with 225 pound springs for this kit.

    • New 56" flange-to-flange Ford 9" housing with attached bracketry
    • New 31-spline high performance induction heat treated forged alloy steel axles
    • 3/4" 4-link bars (choose plain steel or polished stainless)
    • 4-bar rod ends with nylon bushings (polished stainless only)

     

    Triangulated Rear 4-Bar Installation Instructions (PDF) (Note: All axle brackets come welded to the housing - disregard welding requirements in instructions as it has already been completed.)

  • Offenhauser 1939-53 Flathead Ford 4-Ring Pistons, 3.75 Stroke, 3.313 Bore
    Offenhauser 1939-53 Flathead Ford 4-Ring Pistons, 3.75 Stroke, 3.313 Bore
    x
                

    Original Flathead pistons used four rings, were somewhat round, had questionable wrist pins and locks and were made of cast iron. These pressure-cast aluminum pistons share the four-ring design, but are cam ground and use modern steel wrist pins and real snap rings. They’re a great upgrade when rebuilding your 1939-1953 flathead Ford or Mercury V8 engine.

    • Original 4-ring design
    • Pressure cast aluminum construction provides great strength and durability
    • Precision cam ground
    • Modern steel wrist pins
    • Snap ring style retainer clips

    The original bore size was 3.188", which makes these .125" oversize. Sold in sets of eight.

Goto Previous PagePrevious Page
1 2 3 4 5 ... 11