Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"ford intake manifold" Page 1 of 4

  • Fel-Pro Gaskets FS7525B 1949-53 Flathead Ford V8 Overhaul Gasket Set
    Fel-Pro Gaskets FS7525B 1949-53 Flathead Ford V8 Overhaul Gasket Set
    x
                

    If you're going to overhaul your Flathead, you're going to need new gaskets. This complete overhaul gasket set is for 1949-1953 Ford and Mercury flathead V8 engines. Includes all the necessary gaskets and seals you need for a typical engine rebuild.

    • High-quality gaskets for a leak-free engine
    • Modern composition head gaskets
    • Head gaskets will fit bores up to 3-3/16" (3.270")
    • Set includes gaskets for:
      • Cylinder Heads
      • Oil Pan
      • Rear Seal
      • Water Pumps
      • Front Packing
      • Fuel Pump
      • Water Necks
      • Timing Cover
      • Valve Seals
      • Intake Manifold
      • Exhaust Manifolds
  • Two Plain 9 Super 7   Carbs, Edelbrock 1103 Slingshot Intake, 1938-48 Ford V8
    Two Plain 9 Super 7 Carbs, Edelbrock 1103 Slingshot Intake, 1938-48 Ford V8
    x
                Please view the product's page for more information
            
  • Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    x
                

    If you are running a maximum effort 260-289-302 S/B Ford V8, then this is the intake for you! Professional Products' Cross Wind design incorporates an open area under the plenum to allow a full flow of cool air to pass through. This is similar to features found on single plane racing manifolds and this design can provide more power and torque due to a cooler, more dense intake charge. This dual plane, 180° performance manifold is designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs.

    • RPM range is 1500-6500 
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • 1/2" NPT water outlets at all four corners
    • Dual distributor hold-downs 
    • Available plain or show polished

    910-11240 Instructions (PDF) 

  • Offenhauser 1075 1949-1953 Ford Flathead Regular Dual Intake Manifold
    Offenhauser 1075 1949-1953 Ford Flathead Regular Dual Intake Manifold
    x
                

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The generator may not fit into the stock location due to the clearance issue with the carburetor.  The generator can be relocated to the passenger side using bracket # 325-1146. If using a GM alternator, use our chrome 916-67909 or plain 916-67910 bracket.

    • Carb Centers:  4-3/4"
    • Carb pads are angled as they were on stock 49-53 intakes
    • Front drivers side accessory hole is for draft tube and measures 1.25"
    • Rear drivers side accessory hole is for oil fill tube and measures 1.375"
  • Edelbrock 1103 1938-48 Ford/Mercury Flathead Slingshot Manifold, Two Carb
    Edelbrock 1103 1938-48 Ford/Mercury Flathead Slingshot Manifold, Two Carb
    x
                

    Edelbrock has decided to re-release this legendary manifold; giving a new generation a chance to own this historic benchmark. Using a pair of two barrel carburetors mounted in a "Y" configuration, this manifold unlocked the potential of Ford's versatile flathead platform for thousands of enthusiasts across the country. The Slingshot manifold is designed for use with 1938-48 style Flatheads, some late model blocks can be modified to work with these heads. It works with standard three bolt Stromberg, Holley and Demon carburetors and allows for the use of a period correct generator mounted in the stock location. 7-3/4" tall. 

    This is a reproduction of the original intake manifold designed by Vic Edelbrock Sr. in 1938. The Slingshot is a real show stopper and even includes stainless acorn nuts for mounting the two halves.  Among the first ever hot rod parts, the famous Edelbrock Slingshot still ranks among the best flathead intakes out there. The Slingshot produces more peak torque than the competitors two carb intakes, as well as more overall average power and torque. The ’38-vintage, two-piece Slingshot more than holds its own even today. If you want a high-rise, Edelbrock’s design is far superior. Includes assembly hardware and gasket #8700.  

    • For 1938-48 Ford/Mercury Flathead
    • Includes assembly hardware and gasket
    • 7-3/4" tall
    • Made in the USA
  • Offenhauser 1090 1932-1948 Ford Flathead Regular Dual Intake Manifold
    Offenhauser 1090 1932-1948 Ford Flathead Regular Dual Intake Manifold
    x
                

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    Has room for generator in stock location, but generally requires an offset bracket. If using a GM alternator, use our chrome 916-67909 or plain 916-67910 bracket.

    • Carb Centers:  4-3/4"
    • For 1932-48 Ford Flatheads
    • Front drivers side accessory hole is for draft tube and measures 1.25"
    • Rear drivers side accessory hole is for oil fill tube and measures 1.375"

     

  • Edelbrock 7535 289-302 Small Block Ford Dual Quad Intake Manifold
    Edelbrock 7535 289-302 Small Block Ford Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted the baddest car in town you needed dual quads under the hood, and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 260-289-302 small-block Ford V8. These Small Block Ford intakes are taller, offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler, denser charge and more horsepower. 

    Carb center spacing is 6-7/16".

    Small Block Ford Dual Intake Manifold Installation Instructions (PDF)

  • Edelbrock 7181 Performer RPM Ford 351W Intake Manifold
    Edelbrock 7181 Performer RPM Ford 351W Intake Manifold
    x
                

    Edelbrock's Performer RPM 351W is designed for 1969 and later 351 Windsor Ford V8 high-performance engines with Edelbrock Performer RPM cylinder heads, modified OEM cylinder heads or equivalent. The dual-plane design offers good throttle response with excellent top-end power for the street. Has a 1500-6500 rpm power band.

    No provisions for choke or rear water crossover. Will fit 1964-1/2 to 1970 Mustangs. Will NOT fit under stock hood of 1974-78 or 1979-95 Mustangs. For van installations use OEM Ford "van" intake gasket set. Will fit early 16-bolt head with Ford 16-bolt intake gasket set.

    IMCA Approved

    325-7181 Instructions (PDF)

  • Edelbrock 5412 289-302 Ford Three Deuce Tri Power Intake Manifold
    Edelbrock 5412 289-302 Ford Three Deuce Tri Power Intake Manifold
    x
                
    This intake for 3 deuces on a small block Ford does NOT have clearance for the Powerfire, Flamethrower, OEM, or any HEI style distributor. It requires the smaller cap as available on distributor 547-8352
    • 289-302 Small Block Ford 3 deuce aluminum intake
    • Designed to use 3 bolt carburetors such as the Speedway 9 Super 7's
    • For Stock/OEM standard deck
    • RPM range, Idle-5,500
    • Low Rise, Dual-plane design
    • Improved throttle response
    • Made of aluminum
    • Natural finish
  • Power+Plus Hurricane 302 Ford Manifold
    From: $249.99
    Power+Plus Hurricane 302 Ford Manifold
    x
                This manifold is designed for racing or serious street applications using stock  cast-iron or aftermarket Windsor style cylinder heads. Includes bosses that can  be drilled and tapped for nitrous. It features a rear water crossover passage  along with four corner tapped water ports. Ports are 1.90” x 1.08” at the gasket  flange and the manifold contains enough material to open ports to 2.10” x 1.25”.  Use Professional Products intake gasket #54600 or Fel-Pro intake gasket #1250 or  #1262. This manifold includes a 1/8-NPT vacuum port under the carb flange, a  feature lacking in competitive manifolds of this type. Note that due to the port  layout on small block Ford engines, a single plane manifold, such as this one,  will typically be suitable for street use as long as the vehicle is not too  heavy.

    910-11230 Instructions (PDF) 

  • Edelbrock 75214 S/B Ford 289-302 Performer RPM Air-Gap Intake Manifold
    Edelbrock 75214 S/B Ford 289-302 Performer RPM Air-Gap Intake Manifold
    x
                

    Designed for street 289-302 c.i.d. Ford V8s, the RPM Air-Gap incorporates the same race-winning technology that's been used on Victor Series competition intakes for years. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    • 1500-6500 RPM power band 
    • Includes nitrous bosses
    • No provision for exhaust heated chokes and no exhaust crossover
    • Aftermarket 4-bbl carbs are not compatible with AOD trans unless used with Lokar bracket SRK-4000

    325-75214 Instructions (PDF)

  • Edelbrock 7585 351W Ford Dual Quad Intake Manifold
    Edelbrock 7585 351W Ford Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted the baddest car in town you needed dual quads under the hood, and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 351W small-block Ford V8s. These intakes are taller, offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler, denser charge and more horsepower.

    Carb center spacing is 6-7/16".

    325-7585 Instructions (PDF)

  • Edelbrock 2981 Victor Jr. Ford 351W Intake Manifold
    Edelbrock 2981 Victor Jr. Ford 351W Intake Manifold
    x
                

    Victor series intake manifolds set the standard for quality and performance in the racing industry. Edelbrock's Victor Jr. 351-W is designed for 1969-Up 351 Windsor V8s using stock 12 or 16 bolt heads, and similar aftermarket heads. Fits standard 351W blocks with 9.50" deck height (not SVO).

    For engines with a 3500-7500 RPM power band. Fits Holley 4150-style Double Pumper carbs. Runners have a 2.70 square-inch cross sectional area.

    325-2981 Instructions (PDF)

  • Weiand 8023 Ford 351W Stealth Intake Manifold
    Weiand 8023 Ford 351W Stealth Intake Manifold
    x
                

    Weiand's Stealth Intake Manifold will give your 351W a significant boost in power over the stock manifold. Manifold will fit stock, GT-40, and TFS cylinder heads.

    • High Rise Dual Plane Design
    • Square Carburetor Mounting Flange
    • No EGR provisions
    • Power band: Idle-6000 RPM

    Note: IMCA Stock Car & Sport Mod Approved

    805-8023 Instructions (PDF)

  • Edelbrock 1109 1949-53 Ford Flathead Triple Deuce Intake Manifold
    Edelbrock 1109 1949-53 Ford Flathead Triple Deuce Intake Manifold
    x
                

    This tri power manifold allows the use of square-bore carbs such as the Edelbrock Performer Series or Thunder Series AVS 500 cfm on the 1949-1953 Ford Flathead engine. This is a reproduction of the vintage Edelbrock #452 two-piece manifold with a new carb adapter flange.

    This reproduction of the vintage Edelbrock manifold #SU 349 allows the use of three 2-barrel carbs on a 1949-53 Ford flathead engines. Accepts Stromberg 3-bolt (97 type), Holley 3-bolt, Ford 94 style 3-bolt and Demon 98 carburetors. Carb spacing is 5-1/8". 

    • For 1949-53 Ford/Mercury Flathead
    • Three Deuce carburetor style
    • Front 1-3/8" diameter oil fill
    • 1-1/4" road draft bosses and a raised fuel pump boss
    • Carb spacing is 5-1/8"
    • Made in the USA
  • Chrome 9 Super 7   Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    Chrome 9 Super 7 Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    x
                Please view the product's page for more information
            
  • Plain 9 Super 7   Carbs on Edelbrock 1100 Intake Manifold, 1938-48 Ford V-8
    Plain 9 Super 7 Carbs on Edelbrock 1100 Intake Manifold, 1938-48 Ford V-8
    x
                Please view the product's page for more information
            
  • Plain 9 Super 7   Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    Plain 9 Super 7 Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    x
                

    This kit uses the Eddie Meyer Flathead Ford intake with Speedway's 9 Super 7 ® carbs. It includes two 9Super7 carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line.   The assembled height on this is 16.25".  Assembly required. 

    9 Super 7 ® Linkage Instructions (PDF)

    Eddie Meyer 49-53 Intake Manifold - 

    These Eddie Meyer intake manifolds are reproduced from the original tooling. This '49-'53 Ford version is a 2-piece, long runner, exhaust heated manifold that is better suited to street use.

    • Precision cast and machined aluminum 
    • Works with stock generator/mount (and aftermarket brackets)
    • 4-3/4" carb centers
    • Provisions for original draft tube and oil filler
    • Accepts common 3-bolt carburetors
    • Overall Height:  7-1/2"
    • Draft Tube Hole:  1.25"
    • Oil Filler Tube Hole:  1.39"

    9 Super 7® Primary Carbs -

    Speedway Motors has incorporated many improvements in the 9 Super 7® while maintaining the Stromberg 97 carburetor's original l

  • Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    x
                

    Give your FE-powered hot rod dual-quad power and nostalgic looks with the new Edelbrock RPM Air-Gap Dual-Quad intake manifold. Designed for 1960-later high-performance street 390-406-410- 427-428 c.i.d. Ford FE engines with a 1500-6500 rpm power band. The manifold carb pad is setup to fit Edelbrock carburetors only, will not work with other square flange carburetors. Will not fit 427 Ford Hi-riser and Tunnel port engines. Has provision for a breather flange at rear. Carb center spacing 6-7/16"

    In Dyno tests on a 390 with Performer RPM heads, Performer RPM camshaft, and Thunder Series AVS carburetor, this manifold made 421 hp and 428 ft./lbs. torque.

    Made in the USA.

     

  • Chrome 9 Super 7   Carbs on Eddie Meyer Intake Manifold Kit, 1932-48 Ford V8
    Chrome 9 Super 7 Carbs on Eddie Meyer Intake Manifold Kit, 1932-48 Ford V8
    x
                

    This kit uses the Eddie Meyer Flathead Ford intake with 9 Super 7® carbs. It includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required.

    Eddie Meyer 32-48 Intake Manifold - 

    Eddie Meyer was a Flathead Ford genius, and you can take advantage of his knowledge and experience with this dual-carb intake reproduced from the original tooling. This short-runner, non-heated manifold fits 1932-1948 Flathead Ford and Mercury V8s.

    • Short, high-flow runners
    • Non-heated design
    • Requires offset generator mounting
    • 8-1/4" carb centers
    • Overall Height:  2-1/2" (from block mount to carb base)

    9 Super 7® Primary Carbs -

    Speedway Motors has incorporated many improvements in the 9Super7 Carb while maintaining the Stromberg 97 carburetor's original look. Features such as the choke assembly, accelerator pump, main jets and cos

  • Edelbrock 1108 1938-48 Ford Flathead Triple Deuce Intake Manifold
    Edelbrock 1108 1938-48 Ford Flathead Triple Deuce Intake Manifold
    x
                

    This tri power reproduction of the vintage Edelbrock manifold #SU 359 allows the use of three 2-barrel carbs on 1938-1948 Ford flathead engines. Accepts Stromberg 3-bolt (97 type), Holley 3-bolt, Ford 94 style 3-bolt and Demon 98 carburetors. Carb spacing is 5-1/8". 

    • Three Deuce carburetor Manifold
    • For 1938-48 Ford/Mercury Flathead
    • Carb spacing is 5-1/8"
    • Made in the USA

     

  • Eddie Meyer 1949-1953 Flathead Intake Manifold
    Eddie Meyer 1949-1953 Flathead Intake Manifold
    x
                

    Take advantage of the knowledge of a true Flathead Ford genius! These Eddie Meyer intake manifolds are reproduced from the original tooling. This '49-'53 Ford version is a 2-piece, long runner, exhaust heated manifold that is better suited to street use.

    • Precision cast and machined aluminum 
    • Works with stock generator/mount (and aftermarket brackets)
    • 4-3/4" carb centers
    • Provisions for original draft tube and oil filler
    • Accepts common 3-bolt carburetors
  • 1937-48 Ford Flathead Spark Plug Wire Looms, Stainless Steel
    1937-48 Ford Flathead Spark Plug Wire Looms, Stainless Steel
    x
                

    These polished stainless steel tubes accommodate spark plug wires up to 7 mm.  They attach to the intake manifold of 1937-1948 flathead Ford V8's while keeping your plug wires neat and organized.

    • Accommodates wires up to 7mm
    • Fully polished stainless steel
    • Attaches to intake manifold of flathead Ford V8's

    Note:  Looms will not work with '49-'53 heads as they will hit the thermostat housing.

  • 1949-1953 Ford Flathead Intake Manifold Gasket
    1949-1953 Ford Flathead Intake Manifold Gasket
    x
                

    These intake manifold gaskets for all 1949-1953 Ford/Mercury Flatheads are easy to trim for matching block ports and intake if necessary.

    • Intake manifold gasket
    • For all 1949-1953 Ford/Mercury Flatheads
    • Easy to trim for matching block ports and intake

     

  • Offenhauser 1072 1932-1941 Ford Flathead Triple Carb Intake Manifold
    Offenhauser 1072 1932-1941 Ford Flathead Triple Carb Intake Manifold
    x
                

    This Offy 3x2 tri power manifold is designed for Stromberg 97-style and Demon 98 carbs ONLY. ("94" style carbs will not fit.) 4-5/8" carb centers. The front of the intake manifold has the boss or flange for the generator or fan assembly to mount to. It also has the fill and draft holes behind this flange.  All include generator adapter brackets.

    • For 1932-41 Ford Flatheads
    • 4-5/8" carb centers
    • Three Deuce carburetor style
    • Has boss or flange for generator or fan assembly to mount to
    • Has the fill and draft holes behind flange
    • Includes generator adapter bracket

     

  • Classic Instruments SN57F Ford Oil Pressure Sender Bushing Kit Adaptor
    Classic Instruments SN57F Ford Oil Pressure Sender Bushing Kit Adaptor
    x
                Classic Instruments' brass angled-bushing kits allow for easy installation on most Ford engines. 

    The Oil Pressure Sender will not clear either the back of the intake manifold or the distributor body on many installations unless the Bushing Kit is used.

    • Bushing kit to install oil pressure sender
    • Ford applications
  • Edelbrock 2921 Victor Jr. Ford 302 Intake Manifold
    Edelbrock 2921 Victor Jr. Ford 302 Intake Manifold
    x
                

    The Edelbrock Victor Series intake manifolds have set the standard for quality and performance in the racing industry. The Victor Jr. 302 is designed for Ford 260-289-302 competition engines using modified stock cast iron or aftermarket Windsor-style cylinder heads.

    The Victor Jr. 302 has no rear water crossover. Port exit size at cylinder head is 1.90" x 1.08" with enough extra material to open it up to 2.10" x 1.18".

    325-2921 Instructions (PDF)

  • Edelbrock 7183 351 Clevor Ford RPM Intake Manifold
    Edelbrock 7183 351 Clevor Ford RPM Intake Manifold
    x
                

    Build a mock Boss 351 engine with a standard 351W block and 351 Cleveland heads using this Performer RPM E-Boss 351 manifold. For both high performance street and competition, the dual-plane design makes outstanding power from 1500 to 6500 rpm and the Cleveland port layout and intake bolt hole pattern fit both 2V and 4V heads. It features 9.5" deck height, Windsor end rails, water neck and distributor hole clearance, front and rear water bosses with a standard square bore carburetor pad.

    Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000.

    IMCA Approved

    325-7183 Instructions (PDF)

     

  • Edelbrock 2121 Small Block Ford 289 Intake Manifold w/o EGR
    Edelbrock 2121 Small Block Ford 289 Intake Manifold w/o EGR
    x
                
    • Popular choice for many applications
    • Great for street and off road
    • provides overall performance improvements in idle to 5500 rpm
    • Non-EGR
  • Offenhauser 1074 1942-1948 Ford Flathead Triple Carb Intake Manifold
    Offenhauser 1074 1942-1948 Ford Flathead Triple Carb Intake Manifold
    x
                

    The Offenhauser tri power manifold is designed for Stromberg 97-style carbs ONLY. Has 4-5/8" carb centers. Features a mount flange at the front of the manifold for Offy fan carrier 560-3499 (sold separately).

    • For 1942-48 Ford Flatheads
    • Three Deuce carburetor style
    • 4-5/8" carb centers
    • Has boss or flange for generator or fan assembly to mount to

     

  • Offenhauser 1073 1942-1948 Ford Flathead Super Dual Intake Manifold
    Offenhauser 1073 1942-1948 Ford Flathead Super Dual Intake Manifold
    x
                The Offy Super Dual intake is a better performer than regular dual. 9-1/8" carb centers. The  front of the intake manifold has the  boss or flange for the generator  or fan assembly to mount to. It also  has the fill and draft holes  behind this flange.  All include generator  adapter brackets.
    • For 1942-48 Ford Flatheads
    • 9-1/8" carb centers
    • Has boss or flange for generator or fan assembly to mount to
    • Has the fill and draft holes behind flange
    • Includes generator adapter brackets
    • 3-3/4" tall (measured from block mount to carb base)
    • 9-1/8" carb centers

    Note: Includes a passenger side, cylinder head mounted generator bracket and a bracket to mount the fan to the front of the intake.

     

  • Offenhauser 1076 1949-1953 Ford Flathead Super Dual Intake Manifold
    Offenhauser 1076 1949-1953 Ford Flathead Super Dual Intake Manifold
    x
                

    The Offy super dual intake is a better performer than regular dual. 9-1/8" carb centers.  The front of the 560-1076 intake manifold has the boss or flange for the generator or fan assembly to mount to. It also has the fill and draft holes behind this flange.

    • For 1949-53 Ford Flatheads
    • 9-1/8" carb centers
    • Has boss or flange for generator or fan assembly to mount to
    • Has the fill and draft holes behind flange
    • Generator adapter bracket NOT included
  • Offenhauser 1079 1932-1948 Ford Flathead 4-Barrel Intake Manifold
    Offenhauser 1079 1932-1948 Ford Flathead 4-Barrel Intake Manifold
    x
                

    This Offy single 4-barrel intake fits the 1932-48 Ford V-8 and features a Carter WCFB bolt pattern. For best results, our techs recommend the Holley 390 CFM 4-BBL which requires the Holley Flathead adapter 135-1935B.

    You may also need to purchase 560-6091, 4" tall carb spacer (in addition to 135-1935B) to use a Holley carb on this intake. The spacer gets the carb high enough so that the base will clear the water hoses.

    • For 1932-48 Ford Flathead, 4-barrel carbs 
    • Requires Holley carb, adaptor, and spacer for best results
  • Offenhauser 1078 1949-1953 Ford Flathead 4-Barrel Intake Manifold
    Offenhauser 1078 1949-1953 Ford Flathead 4-Barrel Intake Manifold
    x
                

    This Offy single 4-barrel intake fits the 1949-53 Ford V-8 and features a Carter WCFB bolt pattern. For best results, our techs recommend the Holley 390 CFM 4-BBL which requires the Holley Flathead adapter 135-1935B.

    You may also need to purchase 560-6091, 4" tall carb spacer (in addition to 135-1935B) to use a Holley carb on this intake. The spacer gets the carb high enough so that the base will clear the water hoses.

    • For 1949-53 Ford Flathead, 4-barrel carbs 
    • Requires Holley carb, adaptor, and spacer for best results

     

  • ARP 154-2102 Small Block Ford 351W 12pt Intake Manifold Bolt Kit
    New
    ARP 154-2102 Small Block Ford 351W 12pt Intake Manifold Bolt Kit
    x
                

    These ARP intake manifold bolt kits come complete with 12 black oxide bolts and washers. They are designed for use with small block Ford 351W engines.

    • Ford 351W
    • 12-point fastener head style
    • Black oxide finish
    • Made in the U.S.A
  • ARP 154-2101 Small Block Ford 12pt Intake Manifold Bolt Kit
    New
    ARP 154-2101 Small Block Ford 12pt Intake Manifold Bolt Kit
    x
                

    This ARP intake manifold bolt kit comes with 12 black oxide finish bolts and washers. They are designed for use small block Ford engines.

    • Small Block Ford
    • 12-point fastener head style
    • Black oxide finish
    • Made in the U.S.A
Goto Previous PagePrevious Page
1 2 3 4