Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"fel pro small block ford" Page 1 of 1

  • Fel-Pro Gaskets 1809 1962-86 Ford 260-302 Oil Pan Gasket Set
    Fel-Pro Gaskets 1809 1962-86 Ford 260-302 Oil Pan Gasket Set
    x
                Fel Pro Blue Stripe oil pan gasket set for 1962-1986 Small Block Ford 260, 289, and 302. Does NOT fit "Boss" 302. 
            
  • Fel-Pro Gaskets 1613 1962-86 S/B Ford 260-351W Valve Cover Gaskets
    Fel-Pro Gaskets 1613 1962-86 S/B Ford 260-351W Valve Cover Gaskets
    x
                Blue Stripe, 3/16" cork-rubber valve cover gaskets for 1962-1986 Ford, Mercury V8 260, 289, 302 (except "BOSS") and 351W V-8. 
            
  • Fel-Pro Gaskets FS7525B 1949-53 Flathead Ford V8 Overhaul Gasket Set
    Fel-Pro Gaskets FS7525B 1949-53 Flathead Ford V8 Overhaul Gasket Set
    x
                

    If you're going to overhaul your Flathead, you're going to need new gaskets. This complete overhaul gasket set is for 1949-1953 Ford and Mercury flathead V8 engines. Includes all the necessary gaskets and seals you need for a typical engine rebuild.

    • High-quality gaskets for a leak-free engine
    • Modern composition head gaskets
    • Head gaskets will fit bores up to 3-3/16" (3.270")
    • Set includes gaskets for:
      • Cylinder Heads
      • Oil Pan
      • Rear Seal
      • Water Pumps
      • Front Packing
      • Fuel Pump
      • Water Necks
      • Timing Cover
      • Valve Seals
      • Intake Manifold
      • Exhaust Manifolds
  • Fel-Pro Gaskets 1810 Ford 351W Oil Pan Gasket Set
    Fel-Pro Gaskets 1810 Ford 351W Oil Pan Gasket Set
    x
                Fel-Pro Blue Stripe oil pan gasket set for 1969-1986 Ford Small Block 351W V8 engine.
            
  • Power+Plus Hurricane 302 Ford Manifold
    From: $249.99
    Power+Plus Hurricane 302 Ford Manifold
    x
                This manifold is designed for racing or serious street applications using stock  cast-iron or aftermarket Windsor style cylinder heads. Includes bosses that can  be drilled and tapped for nitrous. It features a rear water crossover passage  along with four corner tapped water ports. Ports are 1.90” x 1.08” at the gasket  flange and the manifold contains enough material to open ports to 2.10” x 1.25”.  Use Professional Products intake gasket #54600 or Fel-Pro intake gasket #1250 or  #1262. This manifold includes a 1/8-NPT vacuum port under the carb flange, a  feature lacking in competitive manifolds of this type. Note that due to the port  layout on small block Ford engines, a single plane manifold, such as this one,  will typically be suitable for street use as long as the vehicle is not too  heavy.

    910-11230 Instructions (PDF) 

  • Fel-Pro Gaskets 1427 Ford N351 Exhaust Header Gaskets
    Fel-Pro Gaskets 1427 Ford N351 Exhaust Header Gaskets
    x
                Fel-Pro Blue Stripe exhaust header gaskets for Ford N351 cylinder heads.
            
  • Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    x
                

    If you are running a maximum effort 260-289-302 S/B Ford V8, then this is the intake for you! Professional Products' Cross Wind design incorporates an open area under the plenum to allow a full flow of cool air to pass through. This is similar to features found on single plane racing manifolds and this design can provide more power and torque due to a cooler, more dense intake charge. This dual plane, 180° performance manifold is designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs.

    • RPM range is 1500-6500 
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • 1/2" NPT water outlets at all four corners
    • Dual distributor hold-downs 
    • Available plain or show polished

    910-11240 Instructions (PDF) 

  • Fel-Pro Gaskets FS7548B 1939-1948 Flathead V8 Overhaul Gasket Set
    Fel-Pro Gaskets FS7548B 1939-1948 Flathead V8 Overhaul Gasket Set
    x
                

    You can't overhaul your Flathead without new gaskets. This overhaul gasket set is for 1939-48 Ford and Mercury V8 and comes complete with all the necessary gaskets and seals you need for a typical engine rebuild.

    Includes modern composition head gaskets. The head gaskets will fit bores up to 3-3/16".

    Kit includes the following gaskets:

    • Cylinder Heads
    • Oil Pan
    • Rear Seal
    • Water Pump
    • Front Packing
    • Fuel Pump
    • Water Neck
    • Timing Cover
    • Valve Seals
    • Intake and Exhaust Gaskets