Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"dual air intake" Page 1 of 5

  • Edelbrock 2701 Performer EPS Chevy Intake Manifold
    Edelbrock 2701 Performer EPS Chevy Intake Manifold
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most.

    IMCA racing approved.

    325-2701 Instructions (PDF)

  • Offenhauser 1075 1949-1953 Ford Flathead Regular Dual Intake Manifold
    Offenhauser 1075 1949-1953 Ford Flathead Regular Dual Intake Manifold
    x
                

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The generator may not fit into the stock location due to the clearance issue with the carburetor.  The generator can be relocated to the passenger side using bracket # 325-1146. If using a GM alternator, use our chrome 916-67909 or plain 916-67910 bracket.

    • Carb Centers:  4-3/4"
    • Carb pads are angled as they were on stock 49-53 intakes
    • Front drivers side accessory hole is for draft tube and measures 1.25"
    • Rear drivers side accessory hole is for oil fill tube and measures 1.375"
  • Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    Edelbrock Big Block Chevy Dual Quad Set-Up, Rectangular Port
    x
                

    There is nothing sweeter looking or sounding than a dual quad on a Chevy! This one kit gets you two manual choke Edelbrock carbs, an Edelbrock unpolished intake manifold, fuel line and special progressive linkage. Just add a suggested air cleaner to finish your installation.

    • 1500-6000 RPM
    • Will clear HEI distributors
    • Will not fit tall-deck truck blocks
    • Has 6-7/16" carb centers

    Overall Height from the bottom of the intake to the top of the air cleaners below:

    325-4237: 11.795"

    325-1235: 11.272"

    325-4119: 12.965"

    Height from bottom of intake to carb mounting surface: 4.899"

    • Port exit dimensions:  1.66" x 2.30

     

  • Edelbrock Big Block Chevy Dual Quad Set-Up, Oval Port
    Edelbrock Big Block Chevy Dual Quad Set-Up, Oval Port
    x
                

    There is nothing sweeter looking or sounding than a dual quad on a Chevy! This one kit gets you two manual choke Edelbrock carbs, an Edelbrock unpolished intake manifold, fuel line and special progressive linkage. Just add a suggested air cleaner to finish your installation.

    • 1500-6000 RPM
    • Will clear HEI distributors
    • Will not fit tall-deck truck blocks
    • Has 6-7/16" carb centers

    Overall Height from the bottom of the intake to the top of the air cleaners below:

    325-4237: 11.795"

    325-1235: 11.272"

    325-4119: 12.965"

    Height from bottom of intake to carb mounting surface: 4.899"

    • Port exit dimensions:  1.64" x 1.94"

     

  • Replacment Dual Quad Air Filter Element, 9-7/8 x 20-1/2 Inch
    Replacment Dual Quad Air Filter Element, 9-7/8 x 20-1/2 Inch
    x
                

    Replacement filter element for dual quad filters. Measures 1-7/8" tall x 9-7/8" wide x 20-1/2" long. Same as Ford part M-9601-A302.

  • Edelbrock 4237 Elite Series Dual Quad Finned Air Cleaner
    Edelbrock 4237 Elite Series Dual Quad Finned Air Cleaner
    x
                

    Designed to fit Edelbrock dual-quad set-ups, this oval air cleaner clears HEI distributors and stock parts. Comes with high-quality 2-1/2" washable, pre-oiled cotton gauze filter for excellent filtration. The oval top comes in a natural, aluminum finish for custom painting. Dimensions: 13-1/2" x 7". 6-7/16" carb center. Edelbrock dual quad air cleaners include a K&N filter element. Finned aluminum. No logo.

    Edelbrock Installation Instructions

  • Edelbrock 7535 289-302 Small Block Ford Dual Quad Intake Manifold
    Edelbrock 7535 289-302 Small Block Ford Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted the baddest car in town you needed dual quads under the hood, and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 260-289-302 small-block Ford V8. These Small Block Ford intakes are taller, offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler, denser charge and more horsepower. 

    Carb center spacing is 6-7/16".

    Small Block Ford Dual Intake Manifold Installation Instructions (PDF)

  • Two Plain 9 Super 7   Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    Two Plain 9 Super 7 Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    x
                

    This kit uses the Offy Dual '49-'53 Flathead Ford intake with Speedway's 9 Super 7® carbs. It includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. 

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb

  • Edelbrock 5426 Small Block Chevy Vortec Dual Quad Intake Manifold
    Edelbrock 5426 Small Block Chevy Vortec Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted to have the baddest car in town, you needed to have dual quads under the hood. These intakes accept Edelbrock carbs and make power in the 1500-6500 RPM range. For Small Block Chevy V8s with 1996 and later Vortec (L31) cast iron or the Edelbrock E-Tec aluminum heads.

    • Low profile for hood clearance on most vehicles
    • Air-conditioning bosses and front oil filler tube boss included
    • Stock alternator brackets do not fit
    • H.E.I. distributor will fit
    • An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines
    • Carburetor Recommendations: Edelbrock Thunder Series AVS carb #1803 and #1804, 500 cfm

    Vortec Dual Quad Intake Manifold Installation Instructions (PDF)

  • Edelbrock Performer Air-Gap Intake Manifold, Small Block V8, Endurashine
    Edelbrock Performer Air-Gap Intake Manifold, Small Block V8, Endurashine
    x
                

    This award-winning design incorporates the same race-winning technology that's been used on Edelbrock's Victor Series competition intakes for years. Designed for 1955-86 262-400 c.i.d. small-block Chevys, the Performer Air-Gap features the air-gap design for the ultimate street performance.  These new Performer Air-Gap manifolds are ideal for street performance from idle-to-5500 rpm.

    The open air-gap separates the runners from the hot lifter-valley cover, resulting in a cooler, denser charge, meaning more power and better throttle response throughout the power band.

    • Chevrolet 262-400 Small-Block V8
    • Dual plane design
    • Idle - 5500 RPM
    • Ideal choice for street rods and street machines
    • For 1987-95 cast iron heads with canted center bolt holes
    • No provision for exhaust heated chokes or exhaust crossover
    • Fits spread-bore or square-bore carburetors
    • Will not fit under stock Corvette hood
    • Available with endurashine finish

    Note: Be sure to include new gaskets with this intake.  Depending on your head application, we recommend choosing from our two suggestions.

    325-26014 Instructions (PDF)

  • Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most. Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains.

    325-27014 Instructions (PDF)

  • Professional Products Crosswind Small Block Chevy Intake Manifold
    Professional Products Crosswind Small Block Chevy Intake Manifold
    x
                

    If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Accepts late model waterneck, A/C, alternator, and HEI

    Fits 1957-1986 heads and includes adapters for use on 1987-1995 small block heads.

  • Edelbrock 2601 Performer Air-Gap Intake Manifold, 1955-86 S/B Chevy
    Edelbrock 2601 Performer Air-Gap Intake Manifold, 1955-86 S/B Chevy
    x
                

    This award-winning design incorporates the same race-winning technology that's been used on our Victor Series competition intakes for years. Designed for 1955-86 262-400 c.i.d. small-block Chevys, the Performer Air-Gap features the air-gap design for the ultimate street performance.  These new Performer Air-Gap manifolds are ideal for street performance from idle-to-5500 rpm.

    The open air-gap separates the runners from the hot lifter-valley cover, resulting in a cooler, denser charge, meaning more power and better throttle response throughout the power band.

    • Chevrolet 262-400 Small-Block V8
    • Dual plane design
    • Idle - 5500 RPM
    • Ideal choice for street rods and street machines
    • No provision for exhaust heated chokes or exhaust crossover
    • Fits spread-bore or square-bore carburetors
    • Will not fit under stock Corvette hood
    • Available with standard finish

    325-2601 Instructions (PDF)

  • Edelbrock 5425 Small Block Chevy Dual Quad Intake Manifold
    Edelbrock 5425 Small Block Chevy Dual Quad Intake Manifold
    x
                

    Edelbrock's C-26 manifold is designed for 1955-1986 262-400 c.i.d. S/B Chevys with a power band of 1500-5000 rpm. This dual-quad is low profile for hood clearance on most vehicles. Air-conditioning bosses and front oil filler tube boss included. Stock alternator brackets DO NOT fit.

    H.E.I. distributor will fit. Use with 500 cfm Edelbrock carbs.

    Dual Quad Intake Manifold Installation Instructions (PDF)

  • Edelbrock 7585 351W Ford Dual Quad Intake Manifold
    Edelbrock 7585 351W Ford Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted the baddest car in town you needed dual quads under the hood, and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 351W small-block Ford V8s. These intakes are taller, offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler, denser charge and more horsepower.

    Carb center spacing is 6-7/16".

    325-7585 Instructions (PDF)

  • Offenhauser 1090 1932-1948 Ford Flathead Regular Dual Intake Manifold
    Offenhauser 1090 1932-1948 Ford Flathead Regular Dual Intake Manifold
    x
                

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    Has room for generator in stock location, but generally requires an offset bracket. If using a GM alternator, use our chrome 916-67909 or plain 916-67910 bracket.

    • Carb Centers:  4-3/4"
    • For 1932-48 Ford Flatheads
    • Front drivers side accessory hole is for draft tube and measures 1.25"
    • Rear drivers side accessory hole is for oil fill tube and measures 1.375"

     

  • Edelbrock 2114 Performer Chevy 4.3 Vortec V6 Aluminum Intake Manifold
    Edelbrock 2114 Performer Chevy 4.3 Vortec V6 Aluminum Intake Manifold
    x
                

    Edelbrock Performer intake manifolds are low-rise, dual-plane designs with patented runner tuning and a 180 degree firing order that you won't find with the competition. This combination boosts torque over a wide rpm range, from idle to 5,500 rpm. These manifolds also deliver improved throttle response over stock intakes.

    • Stock/OEM standard deck
    • Dual plane - idle - 5,500 rpm
    • Natural aluminum finish
    • Non-EGR

    325-02114 Instructions (PDF)

    Notes: This intake manifold must be used with 1996 and later Vortec style cylinder heads (even if they are installed on pre-Vortec blocks). Accepts late model water neck, alternator, HEI, and air conditioning. Has provision for external water bypass. Will not accept stock carburetors or 262 TBI unit.

  • Edelbrock 7516 Performer RPM Air-Gap Vortec S/B Chevy Intake Manifold
    Edelbrock 7516 Performer RPM Air-Gap Vortec S/B Chevy Intake Manifold
    x
                

    Based on the proven Performer RPM Vortec, this single four-barrel intake is designed for 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or Edelbrock E-Tec aluminum heads. The unique Air-Gap design separates the hot engine valley from the air/fuel mixture for a cooler, denser charge and more power throughout the rpm range.

    An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines. Includes rear water outlets, nitrous bosses, a temp sensor boss that clears all waternecks, two distributor clamp locations and a heater outlet boss that's angled for proper fit over the valve cover.

    • Accepts 1976 and later alternator and air-conditioning brackets
    • For square-bore carbs
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Will not fit under stock Corvette hood

    Edelbrock Intake Manifold Installation Instructions (PDF)

  • Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    x
                

    If you are running a maximum effort 260-289-302 S/B Ford V8, then this is the intake for you! Professional Products' Cross Wind design incorporates an open area under the plenum to allow a full flow of cool air to pass through. This is similar to features found on single plane racing manifolds and this design can provide more power and torque due to a cooler, more dense intake charge. This dual plane, 180° performance manifold is designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs.

    • RPM range is 1500-6500 
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • 1/2" NPT water outlets at all four corners
    • Dual distributor hold-downs 
    • Available plain or show polished

    910-11240 Instructions (PDF) 

  • Edelbrock 75614 RPM Air-Gap 2-O B/B Chevy Intake Manifold
    Edelbrock 75614 RPM Air-Gap 2-O B/B Chevy Intake Manifold
    x
                

    Designed for street 396-502 c.i.d. Chevy V8s (1500-6500 rpm) with large oval-port cylinder heads (1975 and earlier), the RPM Air-Gap incorporates the same race-winning technology that's been used in the Victor Series competition intakes for years. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power. Includes rear water outlets, two distributor clamp locations and nitrous bosses.

    • Accepts all late model alternator and A/C brackets
    • For square bore carburetors only
    • No provision for exhaust heated chokes and no exhaust crossover
    • Will not fit under stock hood of Corvette, 1965-67 Chevelle or 1967-81 Camaro

    Instruction Sheet (PDF)

  • Edelbrock 75164 262-400 Chevy EnduraShine RPM Air-Gap Vortec Intake
    Edelbrock 75164 262-400 Chevy EnduraShine RPM Air-Gap Vortec Intake
    x
                

    Based on the powerful Performer RPM Vortec #7116, single four-barrel intake is designed for 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or the new Edelbrock E-Tec aluminum heads.The RPM Air-Gap manifold delivers outstanding performance using the same air-gap technology found in our race-winning Victor manifolds. This unique design separates the hot engine valley from the air/fuel mixture for a cooler, denser charge and more power throughout the rpm range. An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines. Includes rear water outlets, nitrous bosses, a temp sensor boss that clears all waternecks, two distributor clamp locations and a heater outlet boss that's angled for proper fit over the valve cover. Accepts 1976 and later alternator and air-conditioning brackets for street installations. For square-bore carbs. No provision for exhaust-heated chokes and no exhaust crossover. Will not fit under stock Corvette hood. Available with EnduraShine finish.

  • Chrome 9 Super 7   Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    Chrome 9 Super 7 Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    x
                

    This kit uses the Offenhauser Dual 1949-1953 Flathead Ford V8 intake with 9 Super 7® carbs. In includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required.

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7 Carb ® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7® in a 2x2 or 3x2

  • Edelbrock 75214 S/B Ford 289-302 Performer RPM Air-Gap Intake Manifold
    Edelbrock 75214 S/B Ford 289-302 Performer RPM Air-Gap Intake Manifold
    x
                

    Designed for street 289-302 c.i.d. Ford V8s, the RPM Air-Gap incorporates the same race-winning technology that's been used on Victor Series competition intakes for years. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    • 1500-6500 RPM power band 
    • Includes nitrous bosses
    • No provision for exhaust heated chokes and no exhaust crossover
    • Aftermarket 4-bbl carbs are not compatible with AOD trans unless used with Lokar bracket SRK-4000

    325-75214 Instructions (PDF)

  • Cobra Style Dual Quad Air Cleaner
    Cobra Style Dual Quad Air Cleaner
    x
                

    This Dual Quad Cobra Style Air Cleaner is a fully polished aluminum casting with 'milled look' fins. Carb adaptors/bases adjust for different spacings. Measures 21-1/2" x 10-1/2" x 4" tall. Fits 5-1/8 " air horn. Includes filter element.

    925-11903 Instructions (PDF)


  • Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    x
                Please view the product's page for more information
            
  • Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    x
                

    If you are running a little more motor, then this is the intake for you! The Professional Products Typhoon manifold is a high performance dual plane, 180° street manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Provisions to add an oil fill tube
    • Accepts late model waterneck, A/C, alternator, and HEI

    910-11265 Dyno Sheet (PDF)

    910-11265 Instructions (PDF) 

  • Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    x
                

    Designed for 1955-86 262-400 c.i.d. Chevrolet V8s, the award-winning RPM Air-Gap incorporates the same race-winning technology that's used on the Victor Series competition intakes. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    Manifold features rear water outlets, two distributor clamp locations and nitrous bosses. Accepts all 1976 and later alternator and A/C brackets for the street. The heater outlet boss is angled for proper fit over the valve cover. The temp sensor boss clears all waternecks.

    • For square-bore carburetors only
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Not for 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    325-75014 Instructions (PDF)

  • Edelbrock 5408 348/409 Dual Quad Intake Manifold, Small Port
    Edelbrock 5408 348/409 Dual Quad Intake Manifold, Small Port
    x
                

    Performer RPM Dual-Quad intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W" Series engines. These manifolds deliver performance improvements in the 1500-6500 rpm range with Edelbrock Performer Series dual-quad carburetors, and they accept Edelbrock dual-quad accessories including fuel lines, throttle linkage, and air cleaners.

    Includes oil fill tube (not installed) and matching push-in breather cap. Use with dual quad linkage and fuel line at right. Carb center-to-center measurement is 6-7/16".

    325-5408 Instructions (PDF)

  • Edelbrock 5409 348/409 Dual Quad Intake Manifold, Large Port
    Edelbrock 5409 348/409 Dual Quad Intake Manifold, Large Port
    x
                

    Performer RPM Dual-Quad intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W" Series engines. These manifolds deliver performance improvements in the 1500-6500 rpm range with Edelbrock Performer Series dual-quad carburetors, and they accept Edelbrock dual-quad accessories including fuel lines, throttle linkage, and air cleaners.

    Includes oil fill tube (not installed) and matching push-in breather cap. Use with dual quad linkage and fuel line at right. Carb center-to-center measurement is 6-7/16".

    325-5409 Instructions (PDF)

  • Edelbrock 7501 Performer RPM Air-Gap Small Block Chevy Intake Manifold
    Edelbrock 7501 Performer RPM Air-Gap Small Block Chevy Intake Manifold
    x
                

    Designed for 1955-86 262-400 c.i.d. Chevrolet V8s, the award-winning RPM Air-Gap incorporates the same race-winning technology that's used on the Victor Series competition intakes. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    Manifold features rear water outlets, two distributor clamp locations and nitrous bosses. Accepts all 1976 and later alternator and A/C brackets for the street. The heater outlet boss is angled for proper fit over the valve cover. The temp sensor boss clears all waternecks.

    • For square-bore carburetors only
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Not for 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    325-7501 Instructions (PDF)

  • Edelbrock 1235 Dual Quad Oval Air Cleaner
    Edelbrock 1235 Dual Quad Oval Air Cleaner
    x
                

    This Edelbrock dual-quad air cleaner clears HEI distributors and all stock components. It will fit all Edelbrock dual-quad manifolds and others with 6-7/16" carb center-to-center. They come with high-quality K&N 2-1/2" washable, pre-oiled cotton gauze filter for excellent filtration.

    Chrome steel.

     

  • R2C Sportsman Series Air Filter, 14 Inch
    R2C Sportsman Series Air Filter, 14 Inch
    x
                

    These air filters are designed for racers looking for maximum horsepower and unmatched dirt stopping ability at an affordable price, the new R2C Sportsman Series filters take race filtration to the next level.

    • Built using an advanced design media that maximizes every category of performance and eliminates the dirt residue found on air cleaner bases,carburetors and inside your engine
    • Dual Sealing beads to lock out dirt
    • Most cost effective solution for teams that may not race 60 shows each year
    • Cleaning is simple using compressed air from inside out, no washing or oiling is necessary
    • Works ideally with low filter clearance applications such as Stock Carswith hoods
    • Eliminates buying paper filters after 1 or 2 races- Saves Money!
    • 14 Inch Diameter
    • Available in 3, 4, 5, and 6" heights
  • Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    x
                

    Give your FE-powered hot rod dual-quad power and nostalgic looks with the new Edelbrock RPM Air-Gap Dual-Quad intake manifold. Designed for 1960-later high-performance street 390-406-410- 427-428 c.i.d. Ford FE engines with a 1500-6500 rpm power band. The manifold carb pad is setup to fit Edelbrock carburetors only, will not work with other square flange carburetors. Will not fit 427 Ford Hi-riser and Tunnel port engines. Has provision for a breather flange at rear. Carb center spacing 6-7/16"

    In Dyno tests on a 390 with Performer RPM heads, Performer RPM camshaft, and Thunder Series AVS carburetor, this manifold made 421 hp and 428 ft./lbs. torque.

    Made in the USA.

     

  • Dart 42811000 Small Block Chevy Dual Plane Intake Manifold
    Dart 42811000 Small Block Chevy Dual Plane Intake Manifold
    x
                

    The perfect match for Dart small-block heads. A boundry layer of cool air beneath the plenum and runners insulates the fuel/air mixture from engine heat. This produces a denser intake charge and makes more power. The dual plane design maximizes mid-range torque, and a ribbed plenum floor promotes fuel atomization.

    • Recommended for 215cc and smaller intake ports
    • Accepts popular 4150 square carburetors
    • Dual distributor hold-downs to simplify timing adjustments
    • Raised water cross-over and air gap insulate intake charge
    • Integral bosses for nitrous injectors
  • Offenhauser 1035 1950-1959 Chevy 6-Cylinder Dual Carb Intake Manifold
    Offenhauser 1035 1950-1959 Chevy 6-Cylinder Dual Carb Intake Manifold
    x
                

    Offenhauser Dual Carb intake manifolds provide a nostalgic appearance while equalizing fuel distribution to all cylinders, improving both performance and economy. With this lightweight cast aluminum manifold, your old "Stovebolt" will be more responsive across the RPM range. Use with two "big base" carburetors (2-15/16" bolt centers) typical of 1954-62 Chevys.

    • Fits 216-235-261 Chevy 6-cylinders
    • 1950-1959 engines w/ PowerGlide
    • 1953-1959 engines w/ Manual Transmission

     

    Included linkage kit is "non-progressive," meaning both carbs operate at the same time.

  • Professional Products Crosswind Pontiac 326-455 Intake Manifold
    Professional Products Crosswind Pontiac 326-455 Intake Manifold
    x
                This is a great street intake for you Pontiac guys. This aluminum dual-plane intake features an air gap under the plenum to help keep the air cooler, which makes more power. It has a Quadra jet and square bore carb pad which allows you to run the popular 4-bbl carbs. Can be drilled and tapped for nitrous. 1500-6500 rpm. 

    910-11262 Instructions (PDF) 

    General Intake Manifold Instructions (PDF) 

  • GM Performance 19201330 Small Block Chevy ZZ4 350 Turn-Key Crate Engine
    GM Performance 19201330 Small Block Chevy ZZ4 350 Turn-Key Crate Engine
    x
                Please view the product's page for more information
            
  • Two Plain 9 Super 7   Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    Two Plain 9 Super 7 Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    x
                Please view the product's page for more information
            
  • Professional Products Crosswind Oldsmobile 400/425-455 Intake Manifold
    Professional Products Crosswind Oldsmobile 400/425-455 Intake Manifold
    x
                Finally a killer street intake for you Olds guys. This aluminum dual plane intake features an air gap under the plenum to help keep the air cooler, which makes more power. It has a square-bore carb pad which allows you to run the popular 4-bbl carbs. Can be drilled and tapped for nitrous. 1500-6500 rpm.

    910-11259 Instructions (PDF) 

    910-11270 Dyno (PDF) 

  • Offenhauser 1073 1942-1948 Ford Flathead Super Dual Intake Manifold
    Offenhauser 1073 1942-1948 Ford Flathead Super Dual Intake Manifold
    x
                The Offy Super Dual intake is a better performer than regular dual. 9-1/8" carb centers. The  front of the intake manifold has the  boss or flange for the generator  or fan assembly to mount to. It also  has the fill and draft holes  behind this flange.  All include generator  adapter brackets.
    • For 1942-48 Ford Flatheads
    • 9-1/8" carb centers
    • Has boss or flange for generator or fan assembly to mount to
    • Has the fill and draft holes behind flange
    • Includes generator adapter brackets
    • 3-3/4" tall (measured from block mount to carb base)
    • 9-1/8" carb centers

    Note: Includes a passenger side, cylinder head mounted generator bracket and a bracket to mount the fan to the front of the intake.

     

Goto Previous PagePrevious Page
1 2 3 4 5