Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"drag tube front shocks" Page 1 of 3

  • AFCO 6875F Reactor 1993-02 Camaro Front Drag Shocks
    AFCO 6875F Reactor 1993-02 Camaro Front Drag Shocks
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    Fits 1993-2002 Chevy Camaro and Pontiac Firebird.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock with included kit
    • 100% co-Tested and Serial Numbered

    Note: Coil-over kit is included with each shock. Coil spring NOT included.

  • AFCO 6855M Reactor 1962-67 Chevy II Front Drag Shock, 5 Inch Stroke
    AFCO 6855M Reactor 1962-67 Chevy II Front Drag Shock, 5 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered
    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    Fits 1962-1967 Chevy II Nova. (May need to "slot" tie bar mount.)

  • AFCO 6845F Reactor Front Drag Shocks - Chevrolet/GM/Dodge
    AFCO 6845F Reactor Front Drag Shocks - Chevrolet/GM/Dodge
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered

    Fits most '55-'96 GM chassis

    Fits 1979-1992 Dodge Ram half-ton 2WD pickup trucks.

    See Applications tab for fittment.

  • AFCO 6865M Reactor Mopar Front Drag Shock, 6 Inch Stroke
    AFCO 6865M Reactor Mopar Front Drag Shock, 6 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered

    106-6865M

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    See Applications tab for Dodge-Plymouth chassis fittment.

  • Nostalgia 1923 T-Bucket Frame Kit
    From: $2,499.99
    Product Rating: 5.00 Stars
    Nostalgia 1923 T-Bucket Frame Kit
    x
                

    The Nostalgia T frame is engineered to provide the ultimate in economy and ease of assembly. It features the same spring-behind-axle front suspension as the Budget T, but includes front shock/headlight mounts. The coilover rear suspension uses traditional-style radius rods and a panhard bar, with all necessary mounts welded in place. If you're looking for an affordable, well-engineered T-bucket chassis requiring only basic mechanical skills to assemble, the Nostalgia T is for you! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link) 

    This product requires a 3-4 week build time.

  • AFCO 3875F Eliminator 1993-02 Camaro Front Shocks - Single Adj
    AFCO 3875F Eliminator 1993-02 Camaro Front Shocks - Single Adj
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready

    Fits 1993-2002 GM F-Body (Chevy Camaro, Pontiac Firebird). Coil-over kit hardware is included.

  • Deluxe 1923 T-Bucket Frame Kit
    From: $2,699.99
    Deluxe 1923 T-Bucket Frame Kit
    x
                

    The all new Deluxe T frame is engineered to deliver the ultimate ride and handling of any T-bucket chassis! An exclusive triangulated four-bar rear suspension with coilover shocks and urethane bushings provides unparalleled adjustability and traction control, plus better ride quality than any other T-bucket chassis on the market. It's paired with urethane-bushed four-bars supporting the spring-behind-axle front suspension. The Deluxe '23 T sets a new standard for the next generation of T-buckets!

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.  

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Basic 1923 T-Bucket Frame Kit
    From: $1,999.99
    Basic 1923 T-Bucket Frame Kit
    x
                

    It doesn't get any simpler than this! Our most basic T-bucket frame is engineered for a simple and economical coil spring rear suspension with traditional-style radius rods. The front suspension is our time-tested transverse-leaf, spring-behind-axle setup with hairpin-style radius rods. Designed for the do-it-yourselfer, this frame has no front shock mounts - you can fabricate your own or choose from those offered by Speedway!

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This item requires a 3-4 week build time.

     

     

  • AFCO 3870F Eliminator 1993-02 Camaro Front Shocks - Double Adj
    AFCO 3870F Eliminator 1993-02 Camaro Front Shocks - Double Adj
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready

    Fits 1993-2002 GM F-Body (Chevy Camaro, Pontiac Firebird). Coil-over kit hardware is included.

  • AFCO 3850F Eliminator 1962-67 Chevy II Front Shocks, Double Adj
    AFCO 3850F Eliminator 1962-67 Chevy II Front Shocks, Double Adj
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    Fits 1962-1967 Chevy II/Nova (may need to "slot" tie bar mount). 

  • Nostalgia 1923 T-Bucket Frame Kit w/ Standard Body/Bed, Channeled Floor
    Nostalgia 1923 T-Bucket Frame Kit w/ Standard Body/Bed, Channeled Floor
    x
                The Nostalgia T frame is engineered to provide the ultimate in economy and  ease of assembly. It features the same spring-behind-axle front suspension as  the Budget T, but includes front shock/headlight mounts. The coilover rear  suspension uses traditional-style radius rods and a panhard bar, with all  necessary mounts welded in place. If you're looking for an affordable,  well-engineered T-bucket chassis requiring only basic mechanical skills to  assemble, the Nostalgia T is for you!  

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.   

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Nostalgia 1923 T-Bucket Frame Kit w/ Standard Body/Bed, Unchanneled Floor
    Nostalgia 1923 T-Bucket Frame Kit w/ Standard Body/Bed, Unchanneled Floor
    x
                The Nostalgia T frame is engineered to provide the ultimate in economy and  ease of assembly. It features the same spring-behind-axle front suspension as  the Budget T, but includes front shock/headlight mounts. The coilover rear  suspension uses traditional-style radius rods and a panhard bar, with all  necessary mounts welded in place. If you're looking for an affordable,  well-engineered T-bucket chassis requiring only basic mechanical skills to  assemble, the Nostalgia T is for you!  

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.   

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • AFCO 3865M Mopar Eliminator Single Adjustable Front Shock, 6 In Stroke
    AFCO 3865M Mopar Eliminator Single Adjustable Front Shock, 6 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • Deluxe 1923 T-Bucket Frame Kit w/ Standard Body and Bed, No Floor
    Deluxe 1923 T-Bucket Frame Kit w/ Standard Body and Bed, No Floor
    x
                The all new Deluxe T frame is engineered to deliver the ultimate ride and  handling of any T-bucket chassis! An exclusive triangulated four-bar rear  suspension with coilover shocks and urethane bushings provides unparalleled  adjustability and traction control, plus better ride quality than any other  T-bucket chassis on the market. It's paired with urethane-bushed four-bars  supporting the spring-behind-axle front suspension. The Deluxe '23 T sets a new  standard for the next generation of T-buckets! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Deluxe 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Channeled Floor
    Deluxe 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Channeled Floor
    x
                The all new Deluxe T frame is engineered to deliver the ultimate ride and  handling of any T-bucket chassis! An exclusive triangulated four-bar rear  suspension with coilover shocks and urethane bushings provides unparalleled  adjustability and traction control, plus better ride quality than any other  T-bucket chassis on the market. It's paired with urethane-bushed four-bars  supporting the spring-behind-axle front suspension. The Deluxe '23 T sets a new  standard for the next generation of T-buckets! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Basic 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Channeled Floor
    Basic 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Channeled Floor
    x
                

    It doesn't get any simpler than this! Our most basic T-bucket frame is engineered for a simple and economical coil spring rear suspension with traditional-style radius rods. The front suspension is our time-tested transverse-leaf, spring-behind-axle setup with hairpin-style radius rods. Designed for the do-it-yourselfer, this frame has no front shock mounts - you can fabricate your own or choose from those offered by Speedway!

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This item requires a 3-4 week build time.

  • Deluxe 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Flat Floor
    Deluxe 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Flat Floor
    x
                The all new Deluxe T frame is engineered to deliver the ultimate ride and  handling of any T-bucket chassis! An exclusive triangulated four-bar rear  suspension with coilover shocks and urethane bushings provides unparalleled  adjustability and traction control, plus better ride quality than any other  T-bucket chassis on the market. It's paired with urethane-bushed four-bars  supporting the spring-behind-axle front suspension. The Deluxe '23 T sets a new  standard for the next generation of T-buckets! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • AFCO 3855M Mopar Eliminator Single Adjustable Front Shock, 5 In Stroke
    AFCO 3855M Mopar Eliminator Single Adjustable Front Shock, 5 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • Nostalgia 1923 T-Bucket Frame Kit w/ Deluxe Body/Bed, Unchanneled Floor
    Nostalgia 1923 T-Bucket Frame Kit w/ Deluxe Body/Bed, Unchanneled Floor
    x
                The Nostalgia T frame is engineered to provide the ultimate in economy and ease of assembly. It features the same spring-behind-axle front suspension as the Budget T, but includes front shock/headlight mounts. The coilover rear suspension uses traditional-style radius rods and a panhard bar, with all necessary mounts welded in place. If you're looking for an affordable, well-engineered T-bucket chassis requiring only basic mechanical skills to assemble, the Nostalgia T is for you! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Nostalgia 1923 T-Bucket Frame Kit w/ Standard Body and Bed, No Floor
    Nostalgia 1923 T-Bucket Frame Kit w/ Standard Body and Bed, No Floor
    x
                The Nostalgia T frame is engineered to provide the ultimate in economy and  ease of assembly. It features the same spring-behind-axle front suspension as  the Budget T, but includes front shock/headlight mounts. The coilover rear  suspension uses traditional-style radius rods and a panhard bar, with all  necessary mounts welded in place. If you're looking for an affordable,  well-engineered T-bucket chassis requiring only basic mechanical skills to  assemble, the Nostalgia T is for you!  

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.   

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • AFCO 3845F Eliminator Front Shocks, Single Adj - Chevy/GM/Dodge Truck
    AFCO 3845F Eliminator Front Shocks, Single Adj - Chevy/GM/Dodge Truck
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    Fits most '55-'96 GM chassis

    Fits most '79-92 Dodge Trucks 

    See Application tab for fittment.

     

  • Nostalgia 1923 T-Bucket Frame Kit w/ Deluxe Body and Bed, No Floor
    Nostalgia 1923 T-Bucket Frame Kit w/ Deluxe Body and Bed, No Floor
    x
                The Nostalgia T frame is engineered to provide the ultimate in economy and ease of assembly. It features the same spring-behind-axle front suspension as the Budget T, but includes front shock/headlight mounts. The coilover rear suspension uses traditional-style radius rods and a panhard bar, with all necessary mounts welded in place. If you're looking for an affordable, well-engineered T-bucket chassis requiring only basic mechanical skills to assemble, the Nostalgia T is for you! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Basic 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Unchanneled Floor
    Basic 1923 T-Bucket Frame Kit w/ Standard Body and Bed, Unchanneled Floor
    x
                

    It doesn't get any simpler than this! Our most basic T-bucket frame is engineered for a simple and economical coil spring rear suspension with traditional-style radius rods. The front suspension is our time-tested transverse-leaf, spring-behind-axle setup with hairpin-style radius rods. Designed for the do-it-yourselfer, this frame has no front shock mounts - you can fabricate your own or choose from those offered by Speedway!

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This item requires a 3-4 week build time.

  • Basic 1923 T-Bucket Frame Kit w/ Standard Body and Bed, No Floor
    Basic 1923 T-Bucket Frame Kit w/ Standard Body and Bed, No Floor
    x
                

    It doesn't get any simpler than this! Our most basic T-bucket frame is engineered for a simple and economical coil spring rear suspension with traditional-style radius rods. The front suspension is our time-tested transverse-leaf, spring-behind-axle setup with hairpin-style radius rods. Designed for the do-it-yourselfer, this frame has no front shock mounts - you can fabricate your own or choose from those offered by Speedway!

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This item requires a 3-4 week build time.

  • Nostalgia 1923 T-Bucket Frame Kit w/ Deluxe Body/Bed, Channeled Floor
    Nostalgia 1923 T-Bucket Frame Kit w/ Deluxe Body/Bed, Channeled Floor
    x
                The Nostalgia T frame is engineered to provide the ultimate in economy and ease of assembly. It features the same spring-behind-axle front suspension as the Budget T, but includes front shock/headlight mounts. The coilover rear suspension uses traditional-style radius rods and a panhard bar, with all necessary mounts welded in place. If you're looking for an affordable, well-engineered T-bucket chassis requiring only basic mechanical skills to assemble, the Nostalgia T is for you! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.  

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Deluxe 1927 T-Bucket Frame Kit
    From: $2,999.99
    Deluxe 1927 T-Bucket Frame Kit
    x
                

    Looking for a little more interior room and a lower profile in your T roadster? Then try our Deluxe '27 T! The all-new Deluxe '27 frame features the same triangulated four-bar rear suspension as the Deluxe T, but with a longer wheelbase and extended rear frame section to accommodate Speedway's high-quality fiberglass '27 T roadster body. The body-and-frame combo can be used to build a hot rod with the same open engine bay and fenderless look of a T-bucket, but offers a lower seating position and a lot more legroom. Try it on for size!

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • AFCO 3840F Eliminator Front Shocks, Double Adj - Chevrolet/GM, Dodge
    AFCO 3840F Eliminator Front Shocks, Double Adj - Chevrolet/GM, Dodge
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D
    Fits 1979-1992 Dodge Ram half-ton pickup trucks

    Fits most '55-'96 GM chassis

    See Application tab for fittment.

  • AFCO 3860M Mopar Eliminator Double Adjustable Front Shock, 6 In Stroke
    AFCO 3860M Mopar Eliminator Double Adjustable Front Shock, 6 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.  By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • AFCO 3850M Mopar Eliminator Double Adjustable Front Shock, 5 In Stroke
    AFCO 3850M Mopar Eliminator Double Adjustable Front Shock, 5 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.  By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • Deluxe '27 T-Bucket Frame Kit w/ Standard Body, Unchanneled Floor
    Deluxe '27 T-Bucket Frame Kit w/ Standard Body, Unchanneled Floor
    x
                Looking for a little more interior room and a lower profile in your T  roadster? Then try our Deluxe '27 T! The all-new Deluxe '27 frame features the  same triangulated four-bar rear suspension as the Deluxe T, but with a longer  wheelbase and extended rear frame section to accommodate Speedway's high-quality  fiberglass '27 T roadster body. The body-and-frame combo can be used to build a  hot rod with the same open engine bay and fenderless look of a T-bucket, but  offers a lower seating position and a lot more legroom. Try it on for size!  

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.   

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Deluxe 1927 T-Bucket Frame Kit w/ Standard Body, No Floor
    Deluxe 1927 T-Bucket Frame Kit w/ Standard Body, No Floor
    x
                Looking for a little more interior room and a lower profile in your T  roadster? Then try our Deluxe '27 T! The all-new Deluxe '27 frame features the  same triangulated four-bar rear suspension as the Deluxe T, but with a longer  wheelbase and extended rear frame section to accommodate Speedway's high-quality  fiberglass '27 T roadster body. The body-and-frame combo can be used to build a  hot rod with the same open engine bay and fenderless look of a T-bucket, but  offers a lower seating position and a lot more legroom. Try it on for size!  

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.   

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Deluxe 1923 T-Bucket Frame Kit w/ Deluxe Body and Bed, Unchanneled Floor
    Deluxe 1923 T-Bucket Frame Kit w/ Deluxe Body and Bed, Unchanneled Floor
    x
                The all new Deluxe T frame is engineered to deliver the ultimate ride  and handling of any T-bucket chassis! An exclusive triangulated four-bar  rear suspension with coilover shocks and urethane bushings provides  unparalleled adjustability and traction control, plus better ride  quality than any other T-bucket chassis on the market. It's paired with  urethane-bushed four-bars supporting the spring-behind-axle front  suspension. The Deluxe '23 T sets a new standard for the next generation  of T-buckets! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

    If ordering the body kit without a floor (715-3200), please note that the door will not be hung. If you order a body kit with a floor (715-3211 or 715-3221), the door will be fitted & hung on its hinges before shipping.

  • Deluxe 1923 T Frame Kit w/ Deluxe Body and Bed, Channeled Floor
    Deluxe 1923 T Frame Kit w/ Deluxe Body and Bed, Channeled Floor
    x
                The all new Deluxe T frame is engineered to deliver the ultimate ride  and handling of any T-bucket chassis! An exclusive triangulated four-bar  rear suspension with coilover shocks and urethane bushings provides  unparalleled adjustability and traction control, plus better ride  quality than any other T-bucket chassis on the market. It's paired with  urethane-bushed four-bars supporting the spring-behind-axle front  suspension. The Deluxe '23 T sets a new standard for the next generation  of T-buckets! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

    If ordering the body kit without a floor (715-3200), please note that the door will not be hung. If you order a body kit with a floor (715-3211 or 715-3221), the door will be fitted & hung on its hinges before shipping.

  • Deluxe '27 T-Bucket Frame Kit w/ Deluxe Body, Unchanneled Floor
    Deluxe '27 T-Bucket Frame Kit w/ Deluxe Body, Unchanneled Floor
    x
                Looking for a little more interior room and a lower profile in your T roadster? Then try our Deluxe '27 T! The all-new Deluxe '27 frame features the same triangulated four-bar rear suspension as the Deluxe T, but with a longer wheelbase and extended rear frame section to accommodate Speedway's high-quality fiberglass '27 T roadster body. The body-and-frame combo can be used to build a hot rod with the same open engine bay and fenderless look of a T-bucket, but offers a lower seating position and a lot more legroom. Try it on for size! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.   

    Doors are shipped hinged and latched, but they do require fitting and hanging onto the body by the owner.

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware.

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

  • Deluxe 1927 T-Bucket Frame Kit w/ Deluxe Body, No Floor
    Deluxe 1927 T-Bucket Frame Kit w/ Deluxe Body, No Floor
    x
                Looking for a little more interior room and a lower profile in your T roadster? Then try our Deluxe '27 T! The all-new Deluxe '27 frame features the same triangulated four-bar rear suspension as the Deluxe T, but with a longer wheelbase and extended rear frame section to accommodate Speedway's high-quality fiberglass '27 T roadster body. The body-and-frame combo can be used to build a hot rod with the same open engine bay and fenderless look of a T-bucket, but offers a lower seating position and a lot more legroom. Try it on for size! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit.   

    Doors are shipped hinged and latched, but they do require fitting and hanging onto the body by the owner.

    All of our T kits are also available with chrome suspension.  This option includes chrome plated: front and rear hairpins, rear coilovers, front axle, front leaf spring, front shocks, steering arms, tie rod, drag link, and related hardware. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build tim

  • Deluxe 1923 T-Bucket Frame Kit w/ Deluxe Body and Bed, No Floor
    Deluxe 1923 T-Bucket Frame Kit w/ Deluxe Body and Bed, No Floor
    x
                The all new Deluxe T frame is engineered to deliver the ultimate ride and handling of any T-bucket chassis! An exclusive triangulated four-bar rear suspension with coilover shocks and urethane bushings provides unparalleled adjustability and traction control, plus better ride quality than any other T-bucket chassis on the market. It's paired with urethane-bushed four-bars supporting the spring-behind-axle front suspension. The Deluxe '23 T sets a new standard for the next generation of T-buckets! 

    Shown with optional rearend and engine mounts installed. This part number does not include a rear axle housing or engine/transmission mounts (as pictured). If you wish to add these items to your chassis, simply purchase these items along with your frame kit. 

    Chassis Exploded View (Link)

    This product requires a 3-4 week build time.

    If ordering the body kit without a floor, please note that the door will not be hung. If you order a body kit with a floor (715-3211 or 715-3221), the door will be fitted & hung on its hinges before shipping.

  • AFCO 3860F/BNC Eliminator BNC Front Shock, Mopar B & E Body
    AFCO 3860F/BNC Eliminator BNC Front Shock, Mopar B & E Body
    x
                

    See Application tab for specific fittment information.

    AFCO's Eliminator BNC Valving Twin Tube Double Adjustable Shocks eliminate bounce. The BNC shocks are designed to better absorb the impact of the car after a wheel stand launch. Works great in Stock, Super Stock, Outlaw 10.5, True Street, and other drag racing classes.

    • 106-3860FBNC
      • Body Mount: 1/2" I.D. Bearing (1.06" wide)
      • Shaft Mount: 9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    Can be converted to a coil-over with kit 106-20135D.

  • AFCO 3850F/BNC Eliminator BNC Front Shock, Mopar & Chevy II
    AFCO 3850F/BNC Eliminator BNC Front Shock, Mopar & Chevy II
    x
                

    See Application tab for specific fittment information.

    AFCO's Eliminator BNC Valving Twin Tube Double Adjustable Shocks eliminate bounce. The BNC shocks are designed to better absorb the impact of the car after a wheel stand launch. Works great in Stock, Super Stock, Outlaw 10.5, True Street, and other drag racing classes.

    • 106-3850FBNC
      • Body Mount: 1/2" I.D. Bearing (1.06" wide)
      • Shaft Mount: 9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    Can be converted to a coil-over with kit 106-20135D.

  • AFCO 3870F/BNC Eliminator BNC Front Shock, 1993-02 Camaro/Firebird
    AFCO 3870F/BNC Eliminator BNC Front Shock, 1993-02 Camaro/Firebird
    x
                

    See Application tab for specific fittment information.

    AFCO's Eliminator BNC Valving Twin Tube Double Adjustable Shocks eliminate bounce. The BNC shocks are designed to better absorb the impact of the car after a wheel stand launch. Works great in Stock, Super Stock, Outlaw 10.5, True Street, and other drag racing classes.

    • 106-3870FBNC
      • Body Mount: Tie Bar Mount w/ 2.625" bolt centers
      • Shaft Mount: 1/2" I.D. Bearing (1.06" wide)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    Can be converted to a coil-over with kit 106-20135D (sold separately, except 106-3870FBNC).

  • Garage Sale - AFCO Reactor 1979-92 Dodge Front Drag Shock
    Garage Sale
    Garage Sale - AFCO Reactor 1979-92 Dodge Front Drag Shock
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered

    Fits 1979-1992 Dodge Ram half-ton 2WD pickup trucks.

     

    This shock is garage sale priced because it has been installed and returned. 

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

Goto Previous PagePrevious Page
1 2 3