Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"double steering joints" Page 1 of 2

  • Unisteer 8050310 Steering U-Joint-1 Inch Double D to 3/4 Inch Double D
    Unisteer 8050310 Steering U-Joint-1 Inch Double D to 3/4 Inch Double D
    x
                

    These polished stainless steel U-joints look great and use a pinch bolt on each end for easy installation.

    This is a size that is used on some large GM steering columns. This specific steering universal joint uses a pinch bolt fastener on the 3/4"DD side and a set screw on the 1"DD side, due to the large size

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

    Fits IDIDIT/Flaming River 1" Double D

  • Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • 1.354" not including the screws (1.534" including), width on the u-joint.
    • 1.125" OD on the ends not including the nut (1.345" including the nut). 

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 3/4-30 Spline 3/4 Round, Small GM '78-UP
    Sweet Mfg. Double Steering U-Joint, 3/4-30 Spline 3/4 Round, Small GM '78-UP
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions.These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

     

  • Sweet Mfg. Double Steering U-Joint, 3/4-30 Spline to 3/4 DD, Small GM '78-UP
    Sweet Mfg. Double Steering U-Joint, 3/4-30 Spline to 3/4 DD, Small GM '78-UP
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

     

  • Sweet Mfg Chrome Steering U-Joint, 17MM DD, 3/4DD, Corvette, Citation Rack
    Sweet Mfg Chrome Steering U-Joint, 17MM DD, 3/4DD, Corvette, Citation Rack
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 1 Inch DD, Ididit/Flaming River Column
    Sweet Mfg Chrome Steering U-Joint, 1 Inch DD, Ididit/Flaming River Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Unisteer 8050300 Steering U-Joint, 3/4 Inch Double D to 3/4 Inch DD
    Unisteer 8050300 Steering U-Joint, 3/4 Inch Double D to 3/4 Inch DD
    x
                

    These polished stainless steel steering U-joints look great and use a pinch bolt on each end for easy installation.

    This particular steering universal joint is made to fit 3/4"DD shafting on both sides. Both sides incorporate the pinch bolt design.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

  • Sweet Mfg Chrome Steering U-Joint, 1 DD to 3/4 DD, Ididit/Flaming River Column
    Sweet Mfg Chrome Steering U-Joint, 1 DD to 3/4 DD, Ididit/Flaming River Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-30 Spline to 1 DD, Small GM P/S '78-Up
    Sweet Mfg Chrome Steering U-Joint, 3/4-30 Spline to 1 DD, Small GM P/S '78-Up
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-30 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-30 Spline to 3/4 DD, Small GM P/S '78-Up
    Sweet Mfg Chrome Steering U-Joint, 3/4-30 Spline to 3/4 DD, Small GM P/S '78-Up
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-30 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 3/4 DD, GM Column
    Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 3/4 DD, GM Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 1" DD
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 1 Inch DD, GM Column
    Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 1 Inch DD, GM Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 1" DD
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 1 DD, Vega, Corvair, GM
    Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 1 DD, Vega, Corvair, GM
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 5/8"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Double U-Joint, 1 Inch-48 Spline to 3/4 Inch DD
    Sweet Mfg Chrome Double U-Joint, 1 Inch-48 Spline to 3/4 Inch DD
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-3/4" Long

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 9/16-26 Spline, 1 DD, Mustang II Manual
    Sweet Mfg Chrome Steering U-Joint, 9/16-26 Spline, 1 DD, Mustang II Manual
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 9/16"-26 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 9/16-26 Spline, 3/4 DD, Mustang II Manual
    Sweet Mfg Chrome Steering U-Joint, 9/16-26 Spline, 3/4 DD, Mustang II Manual
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 9/16"-26 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-48 Spline to 1 Inch DD, Wilwood, MGB
    Sweet Mfg Chrome Steering U-Joint, 3/4-48 Spline to 1 Inch DD, Wilwood, MGB
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-48 Spline
    • Wilwood, Sweet, Jaguar, MGB
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-48 Spline to 3/4 DD, Wilwood, MGB
    Sweet Mfg Chrome Steering U-Joint, 3/4-48 Spline to 3/4 DD, Wilwood, MGB
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-48 Spline
    • Wilwood, Sweet, Jaguar, MGB
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-36 Spline, 3/4 DD, GM Manual/Mustang II
    Sweet Mfg Chrome Steering U-Joint, 3/4-36 Spline, 3/4 DD, GM Manual/Mustang II
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-36 Spline

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 Round, IDIDIT/Flaming River
    Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 Round, IDIDIT/Flaming River
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    • Overall length is 5-1/2”
    • O.D. at ends is 1.12”
    • O.D. in the middle is 1.476”
    • O.D. at caps is 1.350”
    • O.D. at cap retainer screws is 1.545”
    • Length of center section is 2-3/4”
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 DD, IDIDIT/Flaming River
    Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 DD, IDIDIT/Flaming River
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Chrome Steering U-Joint, 13/16-36 Spline, 3/4 Inch DD, Big GM Pre '78
    Sweet Mfg. Chrome Steering U-Joint, 13/16-36 Spline, 3/4 Inch DD, Big GM Pre '78
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. They feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 13/16"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 5/8 36-Spline to 3/4 DD, Vega/Corvair/GM
    Sweet Mfg. Double Steering U-Joint, 5/8 36-Spline to 3/4 DD, Vega/Corvair/GM
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    • Overall length is 5-1/2”
    • O.D. at ends is 1.12”
    • O.D. in the middle is 1.476”
    • O.D. at caps is 1.350”
    • O.D. at cap retainer screws is 1.545”
    • Length of center section is 2-3/4”
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 5/8-36 Spline 3/4 Round, Vega/Corvair/GM
    Sweet Mfg. Double Steering U-Joint, 5/8-36 Spline 3/4 Round, Vega/Corvair/GM
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    • Overall length is 5-1/2”
    • O.D. at ends is 1.12”
    • O.D. in the middle is 1.476”
    • O.D. at caps is 1.350”
    • O.D. at cap retainer screws is 1.545”
    • Length of center section is 2-3/4”
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

     

  • Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3/4 Inch Round, MII
    Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3/4 Inch Round, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

     

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch Round
    Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch Round
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3-4 Inch DD, MII
    Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3-4 Inch DD, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch DD, GM Column
    Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch DD, GM Column
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 Inch 48-Spline to 3/4 Inch DD, GM Column
    Sweet Mfg. Double Steering U-Joint, 1 Inch 48-Spline to 3/4 Inch DD, GM Column
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Round, GM, MII
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Round, GM, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. This Mustang II power rack steering universal joint is made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Double Steering U-Joint, .620 Inch-36 Spline to 3/4 Inch Round, Chrysler
    Double Steering U-Joint, .620 Inch-36 Spline to 3/4 Inch Round, Chrysler
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

     

  • Sweet Mfg. Double Steering U-Joint, 1 Inch-48 Spline to 3/4 Inch Round, GM Column
    Sweet Mfg. Double Steering U-Joint, 1 Inch-48 Spline to 3/4 Inch Round, GM Column
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    • Overall length is 5-1/2”
    • O.D. at ends is 1.12”
    • O.D. in the middle is 1.476”
    • O.D. at caps is 1.350”
    • O.D. at cap retainer screws is 1.545”
    • Length of center section is 2-3/4”
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

     

  • Sweet Mfg. Double Steering U-Joint, 3/4 Round to 3/4 Round, Universal
    Sweet Mfg. Double Steering U-Joint, 3/4 Round to 3/4 Round, Universal
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.
  • Sweet Mfg Chrome Steering U-Joint, 3/4-36 Spline, 1 DD, GM Manual/Mustang II
    Sweet Mfg Chrome Steering U-Joint, 3/4-36 Spline, 1 DD, GM Manual/Mustang II
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. They feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Steering U-Joint, 3/4 Inch DD to 1 Inch DD, GM Column / Universal
    Sweet Mfg Steering U-Joint, 3/4 Inch DD to 1 Inch DD, GM Column / Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 3.875 inches long and 1.375 inches in diameter. 

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • U-Joint=3.875" L x 1.375" D
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Inch DD, GM, MII
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Inch DD, GM, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. This Mustang II power rack U joint is made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch Round to 3/4 Inch DD, Universal
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch Round to 3/4 Inch DD, Universal
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. Made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Unisteer 8050330 Steering U-Joint-3/4 Inch Double D to 3/4 Inch Smooth
    Unisteer 8050330 Steering U-Joint-3/4 Inch Double D to 3/4 Inch Smooth
    x
                

    These polished stainless steel U-joints look & function beautifully and use non-pinch bolts which will need to be either welded, cross-drilled and pinned or bolted. These steering universal joints are 3-3/4 inches in length and have an outside diameter of 1.650 inches.

    • The OD is 1.650" (41.90mm) 
    • 3-3/4" in total length
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

  • Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 1 Inch DD, Universal
    Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 1 Inch DD, Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering  universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • 1.354" not including the screws (1.534" including), width on the u-joint.
    • 1.125" OD on the ends not including the nut (1.345" including the nut). 
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Goto Previous PagePrevious Page
1 2