Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"distributor cap points" Page 1 of 2

  • Mallory Ignition 2572101 32-41 Flathead 3 Bolt Dual Point Distributor
    Mallory Ignition 2572101 32-41 Flathead 3 Bolt Dual Point Distributor
    x
                

    Mallory dual point distributors stabilize contact points eliminating point float and bounce to increase coil output. Super-Duty Cap and Rotor feature brass terminals to prevent shorting and arcing. Distributor is "ready-to-run" as the points, condenser, rotor and cap are all installed. Points are set to the proper gap.

    • Fits '32-'41 3-bolt mount Flathead V8
    • Adjustable mechanical advance
    • Self-lubricating bushings provide years of trouble-free service
    • Uses special heavy-duty points for increased RPM range & coil output
    • Ready to install & run

    500-2571601 Instructions (PDF)

    Note: This distributor is very likely to be in the way of the stock fan when used on 1941-1948 Ford and Mercurys. An electric fan may solve this problem.

  • PerTronix 1181 Ignitor Points Eliminator Kit, 1957-74 GM V8
    PerTronix 1181 Ignitor Points Eliminator Kit, 1957-74 GM V8
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    Ignitor Points Eliminator Installation Instructions (PDF)

  • PerTronix D100701 Chevy Flame-Thrower Distributor
    PerTronix D100701 Chevy Flame-Thrower Distributor
    x
                Please view the product's page for more information
            
  • PerTronix 1281 Ignitor Points Eliminator Kit, 1957-74 Ford V8
    PerTronix 1281 Ignitor Points Eliminator Kit, 1957-74 Ford V8
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1281 Instructions (PDF)

  • Mallory Ignition 2572001 42-48 Flathead 2 Bolt Dual Point Distributor
    Mallory Ignition 2572001 42-48 Flathead 2 Bolt Dual Point Distributor
    x
                

    Mallory dual point distributors stabilize contact points eliminating point float and bounce to increase coil output. Super-Duty Cap and Rotor feature brass terminals to prevent shorting and arcing.

    • For '42-'48 Flatheads with 2-bolt mount
    • Adjustable mechanical advance
    • Self-lubricating bushings provide years of trouble-free service
    • Uses special heavy-duty points for increased RPM range & coil output
    • Ready to install & run

    500-2318001 Instructions (PDF)

  • Mallory Ignition 5072101 32-41 Flathead 3 Bolt Electronic Distributor
    Mallory Ignition 5072101 32-41 Flathead 3 Bolt Electronic Distributor
    x
                

    Mallory Magnetic Breakerless Electronic Distributor for 1932-1941 Ford Flathead V8 with the 3-bolt mount. Includes Mallory Super-Duty cap (points style) and rotor with brass terminals.

    • Adjustable mechanical advance
    • Self-lubricating bushings provide years of trouble-free service
    • Easy 3-wire hookup
    • Does not require an external control box
    • For 12 volt systems only

    500-5071601 Instructions (PDF)

     

    Note: This distributor requires 1.4 ohms of coil resistance. If you are using a coil with less than 1.4 ohms, you must us a ballast resistor that will achieve the required 1.4 ohm total resistance. If you are using coil # 447-45001, no resistor will be required.

  • PerTronix D650701 Flame-Thrower V8 Distributor Cap, Red, Socket-Type
    PerTronix D650701 Flame-Thrower V8 Distributor Cap, Red, Socket-Type
    x
                Genuine PerTronix high performance replacement cap for your 8 cylinder Flame-Thrower Billet Distributor. Red color with points socket-style towers.
            
  • PerTronix 1168LS Ignitor Points Eliminator Kit, 1939-62 GM 6 Cyl.
    PerTronix 1168LS Ignitor Points Eliminator Kit, 1939-62 GM 6 Cyl.
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1168 Instructions (PDF)

  • PerTronix ML-181 Ignitor Kit-Mallory 8 Cylinder Dual Point Distributor
    PerTronix ML-181 Ignitor Kit-Mallory 8 Cylinder Dual Point Distributor
    x
                

    Never change points again with the PerTronix Ignitor System. Kit completely replaces points ignition providing increased voltage for improved performance and fuel efficiency over your old Mallory Dual Point ignition. The system fits neatly underneath the distributor cap and is compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-181 Instructions (PDF)

  • PerTronix ML-141 Ignitor Kit-Mallory 4 Cylinder Dual Point Distributor
    PerTronix ML-141 Ignitor Kit-Mallory 4 Cylinder Dual Point Distributor
    x
                

    Never change points again with the PerTronix Ignitor System. Kit completely replaces points ignition providing increased voltage for improved performance and fuel efficiency over your old Mallory Dual Point ignition. The system fits neatly underneath the distributor cap and is compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-141 Instructions (PDF)

  • PerTronix ML-161 Ignitor Kit-Mallory 6 Cylinder Dual Point Distributor
    PerTronix ML-161 Ignitor Kit-Mallory 6 Cylinder Dual Point Distributor
    x
                

    Never change points again with the PerTronix Ignitor System. Kit completely replaces points ignition providing increased voltage for improved performance and fuel efficiency over your old Mallory Dual Point ignition. The system fits neatly underneath the distributor cap and is compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-161 Instructions (PDF)

  • PerTronix 1183 Ignitor Points Eliminator Kit, 1931-58 GM 8 Cyl.
    PerTronix 1183 Ignitor Points Eliminator Kit, 1931-58 GM 8 Cyl.
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1183 Instructions (PDF)

  • MSD 8437 Chevy V8 Distributor Cap
    MSD 8437 Chevy V8 Distributor Cap
    x
                

    All MSD Extra Duty Distributor Caps are designed with performance in mind and are molded from high quality, voltage insulating material and use low resistance terminals.

  • PerTronix 1383 Ignitor Points Eliminator Kit, 1951-58 Mopar V8
    PerTronix 1383 Ignitor Points Eliminator Kit, 1951-58 Mopar V8
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1383 Instructions (PDF)

  • Speedway Points Type Cap for Chevy V8
    Speedway Points Type Cap for Chevy V8
    x
                Speedway points type cap for 1957-1974 Chevy V8. Direct replacement for MSD cap #8437. Cap uses the "L" shaped attaching hardware.
            
  • Mallory Ignition 2318001 49-62 Chevy 6-Cylinder Dual Point Distributor
    Mallory Ignition 2318001 49-62 Chevy 6-Cylinder Dual Point Distributor
    x
                

    Mallory dual point distributors stabilize contact points eliminating point float and bounce to increase coil output. Super-Duty Cap and Rotor feature brass terminals to prevent shorting and arcing. Fits 1949-1962 Chevy 216, 235, and 261 engines.

    • Adjustable mechanical advance
    • Self-lubricating bushings provide years of trouble-free service
    • Uses special heavy-duty points for increased RPM range & coil output
    • Ready to install & run

    500-2318001 Instructions (PDF)

  • PerTronix 1144A Ignitor Points Eliminator Kit, 1962-74 Chevy 4 Cyl.
    PerTronix 1144A Ignitor Points Eliminator Kit, 1962-74 Chevy 4 Cyl.
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1144 Instructions (PDF)

  • PerTronix 1361A Ignitor Points Eliminator Kit, 1960-72 Mopar 6 Cyl.
    PerTronix 1361A Ignitor Points Eliminator Kit, 1960-72 Mopar 6 Cyl.
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1361 Instructions (PDF)

  • PerTronix 1162A Ignitor Points Eliminator Kit, 1963-74 GM 6 Cyl.
    PerTronix 1162A Ignitor Points Eliminator Kit, 1963-74 GM 6 Cyl.
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1162 Instructions (PDF)

  • PerTronix 1261 Ignitor Points Eliminator Kit, 1949-74 Ford 6 Cylinder
    PerTronix 1261 Ignitor Points Eliminator Kit, 1949-74 Ford 6 Cylinder
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1261 Instructions (PDF)

  • PerTronix 1381A Ignitor Points Eliminator Kit, 1962-75 Mopar V8
    PerTronix 1381A Ignitor Points Eliminator Kit, 1962-75 Mopar V8
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1381 Instructions (PDF)

  • PerTronix 1282 Ignitor Points Eliminator Kit, 1954-56 Ford V8
    PerTronix 1282 Ignitor Points Eliminator Kit, 1954-56 Ford V8
    x
                

    Never change points again with the PerTronix Ignitor points conversion kit. It provides increased voltage for improved performance and fuel efficiency. The system completely eliminates the contact points and fits neatly underneath the distributor cap for a "stock" look. Compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems can be used with any stock point-type coil, or use the Flame-Thrower 40,000 volt coil for maximum performance. Also compatible with MSD ignition boxes.

    • Delivers 2x the voltage to the plugs for more power and MPG
    • 2:1 improvement over points in current fall time, increasing coil output
    • Hall Effect Trigger with no moving parts
    • Epoxy molding makes module impervious to contamination
    • Fits entirely inside distributor for a clean, stock look
    • Stable timing - no adjustment needed
    • Will trigger most multi-spark CD ignitions
    • Easy installation

    447-1283 Instructions (PDF)

  • Crane Cams 7501710 1957-74 XRi Chevy V8 Points Ignition Conversion Kit
    Crane Cams 7501710 1957-74 XRi Chevy V8 Points Ignition Conversion Kit
    x
                Here’s the easiest points conversion kit on the market. Simply remove the old points and condenser, install the XR-i on the supplied adapter plate, and run a couple of wires. Everything fits under the OEM distributor cap so you retain a restoration-perfect “factory look.” 
    • Never replace points again
    • Fits 1957-1974 Chevy V8
    • Easy two wire hookup
    • Improved starting and mileage
    • Built-in 4000-8000 RPM adjustable rev limiter
    • Picks up timing from distributor cam lobe
    • Fully sealed
    • Operating Voltage:  6-18 Volts, reverse polarity protection, negative ground
    • Current Draw:  3 amps max @ 5,500 RPM
    • RPM Operating Range:  8,000 RPM
    • RPM Limiter Range:  4,000 to 8,000 RPM
    • Primary Voltage Output:  400 volts (inductive discharge)
    • Primary Energy utput:  45 millijoules w/ PS20 coil and 1.65L ballast resistor
    • Peak Spark Gap Current:  50 milliamps w/ PS20 Coil and 1.65L ballast resistor
    • Spark Duration:  2100 microseconds @ 2,000 RPM

    Instructions (PDF)

  • Crane Cams 7501705 1959-74 Ford V8 XRI Points Ignition Conversion Kit
    Crane Cams 7501705 1959-74 Ford V8 XRI Points Ignition Conversion Kit
    x
                

    Here’s the easiest points conversion kit on the market. Simply remove the old points and condenser, install the XR-i electronic ignition module on the supplied adapter plate, and run a couple of wires. Everything fits under the OEM distributor cap so you retain a restoration-perfect “factory look.”  

    Each kit includes a Crane PS20 1.4 ohm oil-filled ignition coil with black finish.

    • Never replace points again
    • Easy two wire hookup
    • Improved starting and mileage
    • Built-in 4000-8000 RPM adjustable rev limiter
    • Picks up timing from distributor cam lobe
    • Fully sealed
    • Operating Voltage: 6-18 Volts, reverse polarity protection, negative ground
    • Current Draw: 3 amps max @ 5,500 RPM
    • RPM Operating Range: 6,500 RPM
    • RPM Limiter Range: 4,000 to 8,000 RPM
    • Primary Voltage Output: 400 volts (inductive discharge)
    • Primary Energy utput: 45 millijoules w/ PS20 coil and 1.65L ballast resistor
    • Peak Spark Gap Current: 50 milliamps w/ PS20 Coil and 1.65L ballast resistor
    • Spark Duration: 2100 microseconds @ 2,000 RPM
    • Coil Dimensions: 2-1/8" D x 5-3/4" L, 1.75 lbs.
    • Coil Primary Resistance: 1.4 ohms
  • Crane Cams 7501715 1957-74 Chevy V8 XRI Points Ignition Conversion Kit
    Crane Cams 7501715 1957-74 Chevy V8 XRI Points Ignition Conversion Kit
    x
                

    Here’s the easiest points conversion kit on the market. Simply remove the old points and condenser, install the XR-i electronic ignition module on the supplied adapter plate, and run a couple of wires. Everything fits under the OEM distributor cap so you retain a restoration-perfect “factory look.”  

    Each kit includes a Crane PS20 1.4 ohm oil-filled ignition coil with black finish.

    • Never replace points again
    • Easy two wire hookup
    • Improved starting and mileage
    • Built-in 4000-8000 RPM adjustable rev limiter
    • Picks up timing from distributor cam lobe
    • Fully sealed
    • Operating Voltage: 6-18 Volts, reverse polarity protection, negative ground
    • Current Draw: 3 amps max @ 5,500 RPM
    • RPM Operating Range: 6,500 RPM
    • RPM Limiter Range: 4,000 to 8,000 RPM
    • Primary Voltage Output: 400 volts (inductive discharge)
    • Primary Energy utput: 45 millijoules w/ PS20 coil and 1.65L ballast resistor
    • Peak Spark Gap Current: 50 milliamps w/ PS20 Coil and 1.65L ballast resistor
    • Spark Duration: 2100 microseconds @ 2,000 RPM
    • Coil Dimensions: 2-1/8" D x 5-3/4" L, 1.75 lbs.
    • Coil Primary Resistance: 1.4 ohms
  • Crane Cams 7501700 1959-74 XRi Ford V8 Points Ignition Conversion Kit
    Crane Cams 7501700 1959-74 XRi Ford V8 Points Ignition Conversion Kit
    x
                

    Here’s the easiest points conversion kit on the market. Simply remove the old points and condenser, install the XR-i on the supplied adapter plate, and run a couple of wires. Everything fits under the OEM distributor cap so you retain a restoration-perfect “factory look.” 

    • Never replace points again
    • Fits 1959-1974 Ford V8
    • Easy two wire hookup
    • Improved starting and mileage
    • Built-in 4000-8000 RPM adjustable rev limiter
    • Picks up timing from distributor cam lobe
    • Fully sealed
    • Operating Voltage:  6-18 Volts, reverse polarity protection, negative ground
    • Current Draw:  3 amps max @ 5,500 RPM
    • RPM Operating Range:  8,000 RPM
    • RPM Limiter Range:  4,000 to 8,000 RPM
    • Primary Voltage Output:  400 volts (inductive discharge)
    • Primary Energy utput:  45 millijoules w/ PS20 coil and 1.65L ballast resistor
    • Peak Spark Gap Current:  50 milliamps w/ PS20 Coil and 1.65L ballast resistor
    • Spark Duration:  2100 microseconds @ 2,000 RPM
  • Mallory Ignition 5072001 42-48 Flathead 2 Bolt Electronic Distributor
    Mallory Ignition 5072001 42-48 Flathead 2 Bolt Electronic Distributor
    x
                Mallory Magnetic Breakerless Electronic Distributor for 1942-1948 Ford  Flathead V8 with the 2-bolt mount. Easy 3-wire hookup. Adjustable mechanical  advance. Includes Mallory Super-Duty cap (Points Style) and rotor with brass  terminals. 

    For 12 volt systems only.


    500-5071501 Instructions (PDF)

    Note: This distributor requires 1.4 ohms of coil resistance. If you are using a coil with less than 1.4 ohms, you must use a ballast resistor that will achieve the required 1.4 ohm total resistance. If you are using coil #447-45001, no resistor will be required.

  • Pertronix 1285LS 1942-48 Flathead Distributor Ignitor Kit, 12V Neg
    Pertronix 1285LS 1942-48 Flathead Distributor Ignitor Kit, 12V Neg
    x
                For nearly forty years, the Ignitor has proven  itself in applications ranging from race cars to tractors. the Ignitor  replaces breaker points and troublesome factory electronic ignitions  with a dependable, self contained and maintenance free electronic  ignition system. the Ignitor has been called the stealth ignition  because of its quick installation and nearly undetectable presence under  your distributor cap. there is no black-box to clutter the engine  compartment. For optimal performance, use the Ignitor with Flame-thrower  40,000 volt coils.
    • For Ford V8 1942-48 Flathead - 12 volt negative ground
    • Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
    • 2:1 improvement over points in current fall time for increased coil output.
    • Rotating cobalt magnets trigger a Hall effect integrated circuit
    • No points to burn, ...no moving parts to wear out.
    • Epoxy molding makes our module impervious to dirt, oil, grease and moisture.
    • Stable timing ...no need for any adjustments.
    • Will trigger most multi-spark cD ignitions.
    • Available for 6 and 12-volt negative and positive ground systems.
    • Legal in all 50 states and Canada. (c.a.r.b. e.o. #D-57-22)
  • Crane Cams 7501720 57-74 Pontiac/67-Up Old XRi Ignition Conversion Kit
    Crane Cams 7501720 57-74 Pontiac/67-Up Old XRi Ignition Conversion Kit
    x
                

    Here’s the easiest points conversion kit on the market. Simply remove the old points and condenser, install the XR-i on the supplied adapter plate, and run a couple of wires. Everything fits under the OEM distributor cap so you retain a restoration-perfect “factory look.” 

    • Never replace points again
    • Easy two wire hookup
    • Improved starting and mileage
    • Built-in 4000-8000 RPM adjustable rev limiter
    • Picks up timing from distributor cam lobe
    • Fully sealed
    • Operating Voltage:  6-18 Volts, reverse polarity protection, negative ground
    • Current Draw:  3 amps max @ 5,500 RPM
    • RPM Operating Range:  8,000 RPM
    • RPM Limiter Range:  4,000 to 8,000 RPM
    • Primary Voltage Output:  400 volts (inductive discharge)
    • Primary Energy utput:  45 millijoules w/ PS20 coil and 1.65L ballast resistor
    • Peak Spark Gap Current:  50 milliamps w/ PS20 Coil and 1.65L ballast resistor
    • Spark Duration:  2100 microseconds @ 2,000 RPM
  • Crane Cams 7501725 57-74 Pontiac/67-Up Old XRI Ignition Conversion Kit
    Crane Cams 7501725 57-74 Pontiac/67-Up Old XRI Ignition Conversion Kit
    x
                

    Here’s the easiest points conversion kit on the market. Simply remove the old points and condenser, install the XR-i electronic ignition module on the supplied adapter plate, and run a couple of wires. Everything fits under the OEM distributor cap so you retain a restoration-perfect “factory look.”  

    Each kit includes a Crane PS20 1.4 ohm oil-filled ignition coil with black finish.

    • Never replace points again
    • Easy two wire hookup
    • Improved starting and mileage
    • Built-in 4000-8000 RPM adjustable rev limiter
    • Picks up timing from distributor cam lobe
    • Fully sealed
    • Operating Voltage: 6-18 Volts, reverse polarity protection, negative ground
    • Current Draw: 3 amps max @ 5,500 RPM
    • RPM Operating Range: 6,500 RPM
    • RPM Limiter Range: 4,000 to 8,000 RPM
    • Primary Voltage Output: 400 volts (inductive discharge)
    • Primary Energy utput: 45 millijoules w/ PS20 coil and 1.65L ballast resistor
    • Peak Spark Gap Current: 50 milliamps w/ PS20 Coil and 1.65L ballast resistor
    • Spark Duration: 2100 microseconds @ 2,000 RPM
    • Coil Dimensions: 2-1/8" D x 5-3/4" L, 1.75 lbs.
    • Coil Primary Resistance: 1.4 ohms
  • PerTronix 1283 Ignitor Kit, 1949-53 Ford Flathead, 12V
    PerTronix 1283 Ignitor Kit, 1949-53 Ford Flathead, 12V
    x
                

    Never change points again with the PerTronix Ignitor System. Provides increased voltage for improved performance and fuel efficiency. The system fits neatly underneath the distributor cap and is compatible with all 12 volt negative ground systems.

    PerTronix Ignitor Systems are designed for use with any stock point type coil or the FlameThrower 40,000 volt coil for maximum performance Also compatible with MSD ignition boxes.

    447-1282 Instructions (PDF)

  • MSD 8393 Chevy 348/409 Ready to Run Pro Billet Distributor
    MSD 8393 Chevy 348/409 Ready to Run Pro Billet Distributor
    x
                

    If you're a 348/409 fan, you'll be excited to learn that you can get a high performance distributor for your classic Chevy engine! This distributor is ready-to-run meaning that you simply need to install it in the engine and connect three wires to fire up the engine. No external ignition controls are required with this distributor because it has a powerful module built into the housing. This module preduces a stout inductive spark that will improve the overall driveablility and performance of your classic Chevy.

    Just above the maintenance-free magnetic pick-up there is a chromoly mechanical advnace assembly that provides a smooth advance of the timing and is easy to adjust. There is also a vacuum canister for cruisers. If you're concerned about looking stock, the distributor accepts a stock-style points distributor cap.

    • Maintenance-free magnetic pick-up never requires adjusting
    • Built-in ignition module delivers a powerful spark
    • Simple and clean three wire installation
    • CARB Approved
  • MSD 8360 Chevy V8 with Internal Module Distributor
    MSD 8360 Chevy V8 with Internal Module Distributor
    x
                Please view the product's page for more information
            
  • MSD 8383 Ford Y-Block Distributor
    MSD 8383 Ford Y-Block Distributor
    x
                Please view the product's page for more information
            
  • MSD 8352 Ford 289-302 Ready-To-Run Distributor
    MSD 8352 Ford 289-302 Ready-To-Run Distributor
    x
                Please view the product's page for more information
            
  • Pertronix Ignitor Kit for 1942-48 Flathead V8 w/ Front Mount Dist., 6 Volt POS
    Pertronix Ignitor Kit for 1942-48 Flathead V8 w/ Front Mount Dist., 6 Volt POS
    x
                For nearly forty years, the Ignitor has proven  itself in applications ranging from race cars to tractors. the Ignitor  replaces breaker points and troublesome factory electronic ignitions  with a dependable, self contained and maintenance free electronic  ignition system. the Ignitor has been called the stealth ignition  because of its quick installation and nearly undetectable presence under  your distributor cap. there is no black-box to clutter the engine  compartment. For optimal performance, use the Ignitor with Flame-thrower  40,000 volt coils.
    • For Ford V8 1942-48 Flathead - 6 volt positive ground
    • Delivers twice the voltage to the spark plugs, increasing horsepower, fuel economy, and spark plug life.
    • 2:1 improvement over points in current fall time for increased coil output.
    • Rotating cobalt magnets trigger a Hall effect integrated circuit
    • No points to burn, ...no moving parts to wear out.
    • Epoxy molding makes our module impervious to dirt, oil, grease and moisture.
    • Stable timing ...no need for any adjustments.
    • Will trigger most multi-spark cD ignitions.
    • Available for 6 and 12-volt negative and positive ground systems.
    • Legal in all 50 states and Canada. (c.a.r.b. e.o. #D-57-22)
  • MSD 8354 Ford 351W Ready-To-Run Pro-Billet Distributor
    MSD 8354 Ford 351W Ready-To-Run Pro-Billet Distributor
    x
                Please view the product's page for more information
            
  • PerTronix D7100801 Chevy Ignitor III Billet Distributor
    PerTronix D7100801 Chevy Ignitor III Billet Distributor
    x
                

    PerTronix Plug-n-Play Ignitor III Flame-Thrower billet distributors give you CD ignition box performance without the box! Ignitor III systems produce multiple sparks through the entire RPM range, but DO NOT require an external ignition "box." Plus, the Ignitor III module has an adaptive dwell feature which maintains peak energy throughout the entire RPM range.

    1. Does NOT have provisions for a vacuum advance. 
    2. Can be used with most ignition coils 0.6 Ohms or greater.
    3. For 12 volt negative ground systems. Requires 12-14 Volts.
    4. Must use suppression spiral core ignition wires (not solid core wires).
    5. NOT for use with CD or multiple spark systems.
    6. Lobe sensor design triggers off the point cam or reluctor and does not require a magnet sleeve.
    7. Not intended for marine use.

    Does NOT have a vacuum advance and comes with an iron distributor gear. Red, points-style socket cap. For S/B and B/B Chevy. 

    447-71801 Instructions (PDF)

  • Mallory Ignition 5027501 1949-53 Ford Flathead Electronic Distributor
    Mallory Ignition 5027501 1949-53 Ford Flathead Electronic Distributor
    x
                

    Tried and true Mallory electronic distributor for your 1949-1953 Flathead Ford. Features magnetic breakerless ignition technology for greatly improved accuracy versus points-style distributors. For 12 volt systems only.

    • Easy 3-wire hookup
    • Adjustable mechanical advance
    • Self-lubricating bushings provide years of trouble-free service
    • Includes Mallory Super-Duty Cap and Rotor with brass terminals
    • Distributor drive gear not included (sold separately)

    Note: This distributor requires 1.4 ohms of coil resistance. If you are using a coil with less than 1.4 ohms, you must use a ballast resistor that will achieve the required 1.4 ohm total resistance. If you are using coil # 447-45001, no resistor will be required.

    500-5027501 Instructions (PDF)

  • Mallory Ignition 4518001 49-62 Chevy 6-Cylinder Electronic Distributor
    Mallory Ignition 4518001 49-62 Chevy 6-Cylinder Electronic Distributor
    x
                

    Mallory Unilite electronic distributors feature state of the art electronics for a high output ignition. Never set points on your Chevy Six again! Fits 1949-1962 Chevy 216, 235, and 261 engines (12 volt only).

    • Adjustable mechanical advance
    • Self-lubricating bushings provide years of trouble-free service
    • Includes Super-Duty cap & rotor with brass terminals
    • Easy 3-wire hook up
    • External ignition control box not required

    500-4518001 Instructions (PDF)

Goto Previous PagePrevious Page
1 2