Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"chevy power kits" Page 1 of 7

  • 1958-64 Chevy Power Steering Conversion Kit
    1958-64 Chevy Power Steering Conversion Kit
    x
                

    You get a new 500 series power steering box, new centerlink, new pitman and idler arm. This is a straight bolt-in conversion, although '58-'60 cars need to order the 910-32582 idler arm adapter. Steering box uses inverted flare fittings, 11/16" fine on the pressure side and 5/8" fine thread on the return side. Has a 3/4" 30-spline input shaft.

    Note:  Some applications require slight modification to the radiator tank to clear the steering box.

    1958-1964 Chevy Power Steering Conversion Installation Instructions 

  • 1955-64 Chevy Power Steering Hose Kit
    1955-64 Chevy Power Steering Hose Kit
    x
                

    Rubber power steering hose kit for 500, 600, & 605 series power steering boxes. Our power steering hose assemblies are an inexpensive alternative to the more costly stainless steel braided hose kits. Return hose will normally need to be cut to length. 

    • 11/16"-18 inverted flare fine (pressure fitting)
    • 5/8"-18 inverted flare fine (return fitting)
    Note:  Power Steering Hose Kit for Small Blocks Only
  • KRC KIT16312015 Basic Serpentine Drive Kit-Crate Chevy Block Mt. Pump
    KRC KIT16312015 Basic Serpentine Drive Kit-Crate Chevy Block Mt. Pump
    x
                

    KRC's basic kits are the perfect starting point for your GM 602 & 604 Crate Engines. Select the kit with the options that suit your application, then choose the appropriate accessory to complete your kit.

    • Complete basic kit
    • GM 602 & 604 Crate Engines
    • Assembly contains:
      • 7.2cc aluminum power steering pump
      • 4.2" aluminum power steering pulley
      • Aluminum driver side lower block mounted power steering pump bracket
      • Pro series pulley kit
      • KRC high performance water pump
      • Water pump spacers
      • Goodyear Gatorback belt
      • Hardware and detailed instructions

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.

    Cast Iron Pump Tech (PDF)

    Cast Iron Pump Installation Instructions (PDF)

    New Pump Tips (PDF)

    Serpentine Pulley Offset (PDF)

  • Billet FM2121PC SBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    Billet FM2121PC SBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    x
                Please view the product's page for more information
            
  • Three Plain 9 Super 7   Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    Three Plain 9 Super 7 Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    x
                

    This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

    Kit includes three carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

    9 Super 7® Linkage Instructions (PDF)

    Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

    The 9Super7 Carb  makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both prima

  • Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    x
                Please view the product's page for more information
            
  • KRC KRC16312115 Serpentine Drive Kit, S/B Chevy, Block Mt Pump w/ Tank
    KRC KRC16312115 Serpentine Drive Kit, S/B Chevy, Block Mt Pump w/ Tank
    x
                Please view the product's page for more information
            
  • KRC KIT16312010Basic Serpentine Drive Kit Crate S/B Chevy Head Mt Pump
    KRC KIT16312010Basic Serpentine Drive Kit Crate S/B Chevy Head Mt Pump
    x
                Please view the product's page for more information
            
  • KRC KIT16312110 Basic Serpentine Drive Kit-S/B Chevy Head Mt Pump/Tank
    KRC KIT16312110 Basic Serpentine Drive Kit-S/B Chevy Head Mt Pump/Tank
    x
                Please view the product's page for more information
            
  • Billet FM2122PC S/B Chevy Mid Mount Serpentine Conversion Kit-Press-On
    Billet FM2122PC S/B Chevy Mid Mount Serpentine Conversion Kit-Press-On
    x
                Please view the product's page for more information
            
  • Speedway Mustang II Crossmember-1937-39 Chevy Pickup Frame, Kit-Deluxe
    Speedway Mustang II Crossmember-1937-39 Chevy Pickup Frame, Kit-Deluxe
    x
                

    These Speedway Mustang IFS kits for 1937-39 Chevy Pickups are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1937-1939 Chevy Pickup frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers below and add to an IFS kit to get a "

  • Speedway Mustang II Crossmember Kit-1940-1946 Chevy Pickup Frame-DLX
    Speedway Mustang II Crossmember Kit-1940-1946 Chevy Pickup Frame-DLX
    x
                

    These Speedway Mustang IFS kits for 1940-46 Chevy Pickups are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1940-1946 Chevy Pickup frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers below and add to an IFS kit to get

  • Billet FM2222PC B/B Chevy Mid Mount Serpentine Conversion Kit Press-On
    Billet FM2222PC B/B Chevy Mid Mount Serpentine Conversion Kit Press-On
    x
                Please view the product's page for more information
            
  • Speedway 1949-1954 Chevy Speedway Mustang II Deluxe Steel Crossmember
    Speedway 1949-1954 Chevy Speedway Mustang II Deluxe Steel Crossmember
    x
                

    These Speedway Mustang IFS kits for 1949-1954 Chevy passenger cars are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1949-1954 Chevy car frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers below and add to an IFS kit to get a

  • 37-48 Chevy Car Crossmember
    $299.99
    Product Rating: 4.00 Stars
    37-48 Chevy Car Crossmember
    x
                

    These Speedway Mustang IFS kits for 1937-1948 Chevy passenger cars are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are all the special, hard-to-make brackets and mounts you will need to complete the installation, plus illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1937-1948 Chevy car frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers

  • 1958-60 Chevy Idler Arm Adaptor Bracket
    1958-60 Chevy Idler Arm Adaptor Bracket
    x
                

    For use with 1958-1960 Chevy full-size power steering conversion kits. This part is used to adapt a 61-64 idler arm on to an earlier 58-60 full size car when upgrading to our power steering conversion kit 910-32580.

     

  • Holley 20-132 LS Accessory Drive Bracket-ALT, P/S, A/C
    Holley 20-132 LS Accessory Drive Bracket-ALT, P/S, A/C
    x
                Please view the product's page for more information
            
  • Clay Smith Hydraulic Roller Cam / Lifter Kit, 280/282 Small Block Chevy 350
    Clay Smith Hydraulic Roller Cam / Lifter Kit, 280/282 Small Block Chevy 350
    x
                

    These camshaft / lifter kits are perfect for use with SBC 350 to 360 CID with Air Flow Research 180/190 runner heads. Max Power 6000-6200 rpm, Peak Torque 3800. This cam takes advantage of the AFR's Intake to Exhaust flow ratio. This cam maximizes the power of these heads creating a forever-long band of power. To extend power another 200 rpm use 1.6 ratio on both intake and exhaust. 15/8" headers are needed too for this application. We recommend a 2400 stall, a 750CFM carb, and a minimum of 9:1 compression.

    • Adv. - 280 / 282
    • .050" - 221 / 223
    • .100" - 191 / 192
    • .200" - 141 / 139
    • .300" - 74 / 64
    • Lift - .510 / .492
    • Centerlines - 104 / 112
    • Lobe Sep. - 108
    • Includes a set of tie-bar style hydraulic roller lifters
  • Three Chrome 9 Super 7   Carbs, 1957-86 Small Block Chevy Edelbrock Intake
    Three Chrome 9 Super 7 Carbs, 1957-86 Small Block Chevy Edelbrock Intake
    x
                

    This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

    Kit includes three chrome plated carbs, the plain finish aluminum intake, 4" chrome air cleaners, linkage kit, chrome fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

    9 Super 7® Linkage Instructions (PDF)

    Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

    The 9Super7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carbure

  • KRC KIT16312610 Serpentine Drive Kit-S/B Chevy, Head Mt. w/o P.S. Pump
    KRC KIT16312610 Serpentine Drive Kit-S/B Chevy, Head Mt. w/o P.S. Pump
    x
                

    KRC's basic kits are the perfect starting point for your GM 602 & 604 Crate Engines. Select the kit with the options that suit your application, then choose the appropriate accessory to complete your kit.

    • Complete basic crate engine kit
    • Designed for GM 602 & 604 Crate Engines
    • Assembly contains:
      • Aluminum driver side cylinder head mounted power steering pump bracket
      • Pro series pulley kit
      • KRC high performance water pump
      • Water pump spacers
      • Hardware and detailed instructions

    Serpentine Pulley Offset (PDF)

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump

  • KRC KIT16312615 Serpentine Drive Kit-S/B Chevy, Block Mt. w/o P.S Pump
    KRC KIT16312615 Serpentine Drive Kit-S/B Chevy, Block Mt. w/o P.S Pump
    x
                

    KRC's basic kits are the perfect starting point for your GM 602 & 604 Crate Engines. Select the kit with the options that suit your application, then choose the appropriate accessory to complete your kit.

    • Complete basic crate engine kit
    • Designed for GM 602 & 604 Crate Engines
    • Assembly contains:
      • Aluminum driver side lower block mounted power steering pump bracket
      • Pro series pulley kit
      • KRC high performance water pump
      • Water pump spacers
      • Hardware and detailed instructions

    Serpentine Pulley Offset (PDF)

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.  

  • Trans-Dapt 11/07/95 CJS Chevy Vega V8 Conversion Kit
    Trans-Dapt 11/07/95 CJS Chevy Vega V8 Conversion Kit
    x
                

    Fits small block Chevy V8 with automatic or manual transmissions. Works with "short" style water pump. Slight modification to oil pan and car's floor pan will be needed. Minimal cutting and welding required.

    • Includes motor mount brackets, bushings, plates and rear crossmember 
    • Uncoated, full length mandrel bent headers
    • Mounts 283-400 S/B Chevy and LT1
    • Designed for use with TH-350 automatic trans

    Note: Will not fit angle plug heads, power steering, power brakes, air conditioning or a Powerglide transmission.

    720-4686 Instructions (PDF)

    418-68340 Instructions (PDF)

  • KRC Power Steering 20102000 Drive Kit
    KRC Power Steering 20102000 Drive Kit
    x
                The KRC Drive Kit works off the water pump pulley to reduce power steering pump speed by 42%.  The kit comes with the necessary pulley, belt, bolts, and spacers.  S/B Chevy.
            
  • Power Steering Hose Kit for 1982-88 T-Bird Steering Rack to GM Pump
    Power Steering Hose Kit for 1982-88 T-Bird Steering Rack to GM Pump
    x
                

    Our standard power steering hose assemblies are an inexpensive alternative to the more costly stainless steel braided hose kits. This set adapts a 1982-1988 T-Bird/Cougar rack or our 91034340-POW rack to a GM style pump. Return hose will normally need to be cut to length.

    The pressure line in this kit has an inverted flare fitting at the pump end along with a 14mm O-ring fitting on the rack end. It also comes with an adaptor so that it can work with an O-ring style (metric) pump fitting. We suggest using power steering pumps 91032922-GM or 910-32908.

    Kit includes:

    • Adapter for the GM pump, to allow it to work with both metric O-ring and standard inverted flare style threads on the power steering pump fitting.
    • The fittings that go into the 1982-1988 T-bird rack which are 14mm O-ring (high pressure) and 16mm O-ring (low pressure return) with the smaller O-ring fitting hose end being the pressure side for the rack.

     

    910-32535 Instructions (PDF)

    91032535 CPP Instructions (PDF) 

  • Billet FM2221PC BBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    Billet FM2221PC BBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    x
                Please view the product's page for more information
            
  • 1955-57 Chevy Power Steering Centerlink Conversion
    1955-57 Chevy Power Steering Centerlink Conversion
    x
                So your car has the original power steering which is a valve on the end of the centerlink. Problem is they never did work right and made switching to a newer steering box a pain. To fix your problem you just unscrew the original power steering valve off the centerlink, screw this gizmo back on and now you can add a new 605 style power steering box and still use your original power steering centerlink. Neat huh.
            
  • Gotta Show 131171 GM Power Steering Hose Kit - 1980-Up
    Gotta Show 131171 GM Power Steering Hose Kit - 1980-Up
    x
                

    These stainless steel braided power steering hose kits allow you to fit them to your 1980-Up GM for a custom look.

    617-4839 Instructions (PDF)  

  • 1955-57 Chevy Power Steering Conversion Kit
    1955-57 Chevy Power Steering Conversion Kit
    x
                

    Included in this kit is a new 500 series power steering box, new centerlink, new pitman and idler arm. Modification of the original steering column is required. Use 910-32460 (1955-56) or 910-32462 (1957) to convert the stock column for use with this kit. This is a straight bolt-on conversion when using our Ididit columns. 

    The top splines on the steering box are 3/4"-30.

    910-32570 Instructions (PDF)

  • Shortened Reverse Pitman Arm for Lowered 1947-59 Chevy Truck w/PS
    New
    Shortened Reverse Pitman Arm for Lowered 1947-59 Chevy Truck w/PS
    x
                

    These shortened pitman arms are designed for use with lowered 1947-59 Chevy Trucks that have our 910-32132 or 910-32134 Power Steering Kit Conversion.

    • Shortened reverse pitman arm
    • For lowered 47-59 Chevy Pickups
    • Use with 91032132 or 91032134 power steering kits
  • 1955-59 Chevy Truck Power Steering Kit
    1955-59 Chevy Truck Power Steering Kit
    x
                

    This kit lets you install a 1969-87 Chevy 2WD power steering box with a 13/16"-36 spline input shaft in your 1955-59 Chevy pickup. Included are the pitman arm, upper steering arm, drag link, intermediate steering shaft to connect to an aftermarket coulumn or modified stock column, and all hardware. Welding required.

    These kits come with spacers and mounting tabs that are welded to the frame of the pickup to mount the steering box. The original steering column will require alteration and must be welded to the collapsible shaft included in the kit.

    910-32134 Instructions (PDF)

  • 1947-54 Chevy Truck Power Steering Kit
    1947-54 Chevy Truck Power Steering Kit
    x
                

    This kit lets you install a 1969-87 Chevy 2WD power steering box with a 13/16"-36 spline input shaft in your 1947-54 Chevy pickup. Included are the pitman arm, steering arm, drag link, collapsible steering shaft and hardware. Welding required.

    These kits come with spacers and mounting tabs that are welded to the frame of the pickup to mount the steering box. The original steering column will require alteration and must be welded to the collapsible shaft included in the kit.

    910-32132 Instructions (PDF)

  • 1963-66 Chevy Pickup Brake Power Booster Kit
    1963-66 Chevy Pickup Brake Power Booster Kit
    x
                

    Complete the disc brake conversion on your 1963-66 Chevy pickup (or enhance your exhisting brake system) with this high quality master cylinder and brake booster kit. It includes a 8" power booster, dual-chamber master cylinder and a proportioning valve specifically designed for 1963-66 Chevy trucks. The easy-to-install kit can be set up for disc/drum or four-wheel disc applications.

    Learn more about selecting the proper master cylinder for your vehicle by reading our tech article. Brake System Selection

  • Professional Products Cyclone Small Block Chevy Intake Manifold
    Professional Products Cyclone Small Block Chevy Intake Manifold
    x
                

    The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds, not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally, each Power+Plus Manifold is 100% pressure tested for leaks to eliminate installation problems. This is our most popular manifold and is showing up on many performance street machines and street rods.

    RPM range is idle to 5500.  Availabe in plain or show polished.

    NOTES: Manifold includes adaptor bushings to also fit 1987-1995 iron or aluminum heads.  Polished intakes have EGR ports with block plates.

     

     

  • Speedway 1955-57 Chevy Deluxe Front Disc Brake Kit
    Speedway 1955-57 Chevy Deluxe Front Disc Brake Kit
    x
                

    Just what's needed to update your classic Tri-Five Chevy! Eliminate those archaic ball bearings and gain first class stopping power all at once with this front disc brake conversion kit. Rotors and caliper brackets bolt onto your original spindles with no modification or machining required. Calipers mount to the front of the spindle.

    This disc brake kit will increase the total front track width by 1-3/4" (7/8” per side).

    • Uses 11" rotors and 1969-72 GM calipers (7/16"-20 inlets)
    • May not clear some 14" wheels
    • Bolts onto stock '55-'57 spindles with no machine work
    • Includes rubber brake hoses

    910-31949 Instructions (PDF)

  • KRC 59020015 Cast Iron SBC Pump Kit Serpentine Block Mount Remote Tank
    KRC 59020015 Cast Iron SBC Pump Kit Serpentine Block Mount Remote Tank
    x
                

    The KRC Cast Iron Steering Pump Kits are new, not rebuilt, and are designed for racing or street use. Designed for small block Chevy engines, these kits have all matched components and are meant for pulleys with a 4.2" serpentine configuration and a block mount bracket. Cast iron pumps have a maximum pump speed of 5,500 RPM. Features -10 AN inlet and -6 AN outlet fittings.

    These kits include:

    • KRC Cast Iron Steering Pump
    • KRC Deluxe Mouting Brackets
    • KRC Spacer Kit
    • KRC Power Steering Reservoir Tank
    • Complete installation instructions

    These components would cost over $360.00 if purchased separately!

    Cast Iron Pump Tech (PDF)

    46659020B Instructions (PDF)

  • KRC 59020010 Cast Iron SBC Pump Kit Serpentine Head Mount Remote Tank
    KRC 59020010 Cast Iron SBC Pump Kit Serpentine Head Mount Remote Tank
    x
                

    The KRC Cast Iron Steering Pump Kits are new, not rebuilt, and are designed for racing or street use. Designed for small block Chevy engines, these kits have all matched components and are meant for pulleys with a 4.2" serpentine configuration and a cylinder head mount bracket. Cast iron pumps have a maximum pump speed of 5,500 RPM. Features -10 AN inlet and -6 AN outlet fittings.

    These kits include:

    • KRC Cast Iron Steering Pump
    • KRC Deluxe Mouting Brackets
    • KRC Spacer Kit
    • KRC Power Steering Reservoir Tank
    • Complete installation instructions

    These components would cost over $360.00 if purchased separately!

    Cast Iron Pump Tech (PDF)

    466-59020H Instructions (PDF)

Goto Previous PagePrevious Page
1 2 3 4 5 6 7