Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"carburetor linkage ends" Page 1 of 2

  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, RH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, RH
    x
                

    This carb linkage rod end has 3/16" fine RH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine RH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98
  • Double End Carburetor Linkage, 9 Inches Long
    Double End Carburetor Linkage, 9 Inches Long
    x
                

    3/16" steel rod carburetor linkage with double ends. Thread size is 10-32 RH and LH. For use with 9 Super 7®, Stromberg 97, and Demon 98 carbs.

  • Double End Carburetor Linkage, 7 Inches Long
    Double End Carburetor Linkage, 7 Inches Long
    x
                

    3/16" steel rod carburetor linkage with double ends. This linkage can be adjusted to fit carb spacings approximately 7" to 7-5/8". The threads at the end of the central rod are 10-32 (3/16" fine), RH on one end, LH on the other.

    For use with 9 Super 7, Stromberg 97, and Demon 98 carbs.

  • Carb Linkage Thread End for 9 Super 7   /Stromberg 97/Demon 98 Carbs, LH
    Carb Linkage Thread End for 9 Super 7 /Stromberg 97/Demon 98 Carbs, LH
    x
                

    This carb linkage rod end has 3/16" fine LH threads (also known as 10-32).  It is intended for use with 9 Super 7 ®, Stromberg 97, and Demon 98 carburators.

    • 3/16" fine LH threads (10-32)
    • Secures with pin
    • Steel
    • .430" Diameter
    • Application:
      • 9 Super 7 ®
      • Stromberg 97
      • Demon 98

     

  • Rochester 2G Extended Secondary Carb Shaft
    Rochester 2G Extended Secondary Carb Shaft
    x
                

    Extended throttle shaft for Rochester 2G carbs. This shaft is for a secondary carb in a tri-power three deuce setup with progressive linkage. Fits small base 2G and 2GC carbs from the mid '50s through approximately 1968 with throttle bore centers of 1.6".

    • Brass construction
    • 6-7/8" shaft  (6.695")
    • 5/16" diameter  (.312")
    • 6-32 x 1/4" socket head screw at the end
    • 1.645" distance from factory linkage end to 1st butterfly screw hole center
    • 11/16" butterfly screw hole centers  (.685")
  • Double End Carburetor Linkage, 3-1/2 Inches Long
    Double End Carburetor Linkage, 3-1/2 Inches Long
    x
                

    3/16" steel rod carburetor linkage with double ends. This linkage can be adjusted to fit carb spacings approximately 4-1/4" to 4-3/4". The threads at the end of the central rod are 10-32 (3/16 fine) RH on one end, LH on the other.

    For use with 9 Super 7, Stromberg 97, and Demon 98 carbs.

  • Single End Carburetor Linkage Rod, 7 Inches Long
    Single End Carburetor Linkage Rod, 7 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Single End Carburetor Linkage Rod, 3-1/2 Inches Long
    Single End Carburetor Linkage Rod, 3-1/2 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Double End Carburetor Linkage, 3 Inches Long, Non-Adjustable
    Double End Carburetor Linkage, 3 Inches Long, Non-Adjustable
    x
                

    This 3" long, double-end carb linkage is constructed from 3/16" steel rod. Non-adjustable design. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • Single End Carburetor Linkage Rod, 9 Inches Long
    Single End Carburetor Linkage Rod, 9 Inches Long
    x
                

    3/16" steel throttle rod carburetor linkage with a single end. For use with 9 Super 7 ®, Stromberg 97, and Demon 98 carbs.

  • AFCO 10175-18 Throttle Linkage Rod Kit, 18 Inch
    AFCO 10175-18 Throttle Linkage Rod Kit, 18 Inch
    x
                
    Adjustable throttle linkage rod kit includes 1/4" plated steel rod with right hand 1/4" male threads on both ends. Kit also includes carb bushings with 1/4" female rod ends, jam nuts and rod.
    • 1/4" plated steel rod w/ r/h 1/4" male threads on both ends
    • Includes carb bushings, 1/4" female rod ends, jam nuts, & rod
    Note: Extra-long thread allows more adjustment
  • Three 2-Barrel Demon 98 Carburetor Hardware Linkage Kit
    Three 2-Barrel Demon 98 Carburetor Hardware Linkage Kit
    x
                

    These linkage kits are designed for use when running Demon 98 carburetors in a 3 x 2's setup.  These kits contain all necessary rod ends and hardware needed for a successful installation.

    • 3 carb x 2-barrel set-up
    • For Demon 98 carbs
    • Hardware only throttle linkage kit
  • Lokar TC-1000BLD Blower Drive Hi-Tech Throttle Cable
    Lokar TC-1000BLD Blower Drive Hi-Tech Throttle Cable
    x
                

    Blower Drive Cables are designed to operate with BDS linkage, Enderle linkage and Weiand linkage for side mounted carburetors. Throttle cables designed with a specially extruded liner for extended life of the cable – not to be confused with ordinary braided brake hose. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. "U-Cut-to-Fit" outer housing is available in a 24" length with a "U-Cut-to-Fit" stainless inner wire. Blower Throttle Cable comes complete with stainless mounting bracket and rod end.

    • Designed to operate with BDS linkage, Enderle linkage and Weiand linkage for side mounted carburetors
    • Specially extruded liner for extended life of the cable
    • Equipped with aluminum fittings and aluminum ferrule to eliminate fraying
    • Complete with stainless mounting bracket and rod end

    Throttle Body and Carb End Fittings Guide (Link)

    Blower Drive Throttle Cable Installation Instructions (PDF)

  • Rochester 2G Tri-Power Base Kit Without Linkage
    Rochester 2G Tri-Power Base Kit Without Linkage
    x
                

    There's nothing cooler than a TriPower on your small block, but  the carbs are expensive and hard to find! With this kit you can use three junk yard 2G small base style Rochester carbs and put together a three deuce set-up for a fraction of the cost.

    Includes two new bases for the secondary front and rear carbs, gaskets, jets, power valve and modified piston, idle tubes, plugs, hardware and new primary throttle shaft and butterflies. The center carb (primary) uses its stock base, and parts are included in the kit to modify your stock primary base.

    This kit doesn't include an adjustable progressive linkage kit, but the linkage is available separately. 

    Rochester 2 GC Tri-Power Carb Installation Instructions (PDF)

  • Edelbrock 7094 Dual Quad Carburetor Linkage
    Edelbrock 7094 Dual Quad Carburetor Linkage
    x
                

    Designed for use with Edelbrock Dual-Quad manifolds and Performer Series carburetors. This linkage kit provides smooth, progressive throttle activation using high-quality aluminum, stainless steel and brass parts with spherical rod ends.

    Fits our dual-quad manifolds (with Edelbrock Performer Series carburetors):

    • 325-5420 B/B Chevy Oval Port (Edelbrock #5420)
    • 325-5425 S/B Chevy (Edelbrock #5425) 
    • 325-5408 Chevy W-Series Small Port (Edelbrock #5408)
    • 325-5409 Chevy W-Series Large Port (Edelbrock #5409)
    • 325-7535 Ford 289-302 (Edelbrock #7535)
    • 325-7585 Ford 351W (Edelbrock #7585)
    325-7094 Instructions (PDF)
  • Weiand 7166 Supercharger Carburetor Linkage Kit
    Weiand 7166 Supercharger Carburetor Linkage Kit
    x
                

    Carburetor linkage for use with side mounted 4V carburetors (6-71 & 8-71 Series). Constructed of high quality rod ends, stainless steel shafts, and black anodized aluminum supports to make hooking up your carburetors a snap.

    805-7166 Instruction Sheet (PDF)

  • Pair of Speedys 9 Super 7    Primary 3-Bolt 2 Barrel Carburetors, Plain
    Pair of Speedys 9 Super 7 Primary 3-Bolt 2 Barrel Carburetors, Plain
    x
                Please view the product's page for more information
            
  • Stromberg 97 Extended Throttle Shaft, .282 Inch Diameter
    Stromberg 97 Extended Throttle Shaft, .282 Inch Diameter
    x
                

    About the only way your 97 could have a tight throttle shaft would be if you found a NOS carb somewhere. Now you can build yourself a dual or triple carb three deuce set-up that will run like new. We offer you these new extended throttle shafts that are .282", which is .005" oversize. You simply run a 9/32" drill bit or reamer through the base plate and you now have a tight carb again.

    • Extended throttle shaft
    • .282" which is .005" oversize
    • Fits 97-style carbs with throttle bore centers of 1.333"
    • Threaded screw hole & machined step to work with OEM throttle linkage
    • Stub shaft to clamp a linkage arm onto it for multi-carb linkage
    • Butterfly screws included
    • Brass construction
    • Threaded End to Center of 1st Butterfly Screw Hole:  1-5/16"

    910-11591 Instructions (PDF)

  • AFCO 10175-21 Throttle Linkage Rod Kit, 21 Inch
    AFCO 10175-21 Throttle Linkage Rod Kit, 21 Inch
    x
                
    Adjustable throttle linkage kit includes 1/4" steel throttle rod with with right hand 1/4" male threads on both ends. Kit also includes carb bushings with 1/4" female rod ends, jam nuts, and rod.
    • 1/4" plated steel rod w/ r/h 1/4" male threads on both ends
    • Includes carb bushings, 1/4" female rod ends, jam nuts, & rod
    Note: Extra-long thread allows more adjustment
  • AFCO 10175-24 Throttle Linkage Rod Kit, 24 Inch
    AFCO 10175-24 Throttle Linkage Rod Kit, 24 Inch
    x
                
    Adjustable throttle Linkage Kit includes 1/4" steel throttle rod with with right hand 1/4" male threads on both ends. Kit also includes carb bushings with 1/4" female rod ends, jam nuts, and rod.
    • 1/4" plated steel rod w/ r/h 1/4" male threads on both ends
    • Includes carb bushings, 1/4" female rod ends, jam nuts, & rod
    Note: Extra-long thread allows more adjustment
  • Edelbrock 1033 94 Triple Carb Throttle Linkage Rod Kit, Progressive
    Edelbrock 1033 94 Triple Carb Throttle Linkage Rod Kit, Progressive
    x
                

    The progressive design operates a single or two carburetors to part throttle before synchronizing all three carbutetors to open fully at wide open throttle.  Edelbrock 94 carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94 carbs.

    • Operates a single or dual carb to half throttle and pregresses all three to WOT
    • Saves fuel, provides smoother throttle operation and ends flat spots
  • Pair of Speedys 9 Super 7    Chrome Primary 3-Bolt 2 Barrel Carburetors
    Pair of Speedys 9 Super 7 Chrome Primary 3-Bolt 2 Barrel Carburetors
    x
                Please view the product's page for more information
            
  • Ford/Holley 94 Extended Throttle Shaft
    Ford/Holley 94 Extended Throttle Shaft
    x
                

    About the only way your 94 carburetor could have a tight throttle shaft would be if you found a NOS carb somewhere. Now you can build yourself a dual or triple carb three deuce set-up that will run like new. We offer you these new extended throttle shafts that are .282" which is .005" oversize. You simply run a 9/32" drill bit or reamer through the base plate and you now have a tight carb again.

    Includes (4) throttle butterfy plate screws and a 6-32 x 1/4" truss head end screw (slotted head).

  • Rochester 2G Extended Primary Carb Shaft
    Rochester 2G Extended Primary Carb Shaft
    x
                

    Extended throttle shaft for Rochester 2G or 2GC carbs. For use in primary carbs in tri-power three deuce setups with progressive linkage. Fits "small base" Rochester 2 barrel carburetors w/ 1.6" throttle bore centers used on 1950's thru approximately 1968 GM cars.

    Use with factory throttle plates or aftermarket plates.

    • Shaft Groove:  .039"
    • Factory throttle arm end to 1st butterfly screw hole center:  1.725"
    • Butterfly Screw Hole Centers:  11/16"  (.685")
  • Edelbrock 1159 94 Carburetor Ball-End Stud Arm
    Edelbrock 1159 94 Carburetor Ball-End Stud Arm
    x
                This part is a bolt on throttle ball that is designed to be used only in conjunction with the Edelbrock 94 carb, part number 3251151. This part bolts to the passenger side of the carburetor, and allows the use of the OEM ball and socket style throttle linkage.
            
  • Carburetor Throttle Rod Linkage Connector, 3/16 Inch
    Carburetor Throttle Rod Linkage Connector, 3/16 Inch
    x
                

    Throttle rod sleeves can be attached to the ends of throttle rods to complete. Attaches to 3/16" diameter rods.

    For use with Super 97, Stromberg 97, and Demon 98.

  • Edelbrock 8131 Performer Carb Fuel Line Kit & Fuel Filter, -6 AN Inlet
    Edelbrock 8131 Performer Carb Fuel Line Kit & Fuel Filter, -6 AN Inlet
    x
                

    These 3/8” fuel line kits have a clean look and are easy to install. These fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution. The drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. The 325-8126 includes a barbed end for a push-on 5/16" or 3/8" rubber fuel line. The 325-8131 includes an aluminum fuel filter with a 40 micron filter element and -6 AN female inlet will accept an Edelbrock fuel line kit for a complete fuel-pump to carburetor plumbing solution. They are manufactured of chrome plated steel and include a 5/8" -20 threaded banjo bolt with gaskets.

    Fuel Line Kit Instruction Sheet (PDF)

  • Carburetor Throttle Rod Linkage Connector, 1/4 Inch
    Carburetor Throttle Rod Linkage Connector, 1/4 Inch
    x
                

    Throttle rod sleeves can be attached to the ends of throttle rods to complete. Attaches to 1/4" diameter rods.

    For use with 9 Super 7, Stromberg 97, and Demon 98 carbs.

  • Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet
    Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet
    x
                

    These 3/8” fuel line kits have a clean look and are easy to install. These fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution. The drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. The 325-8126 includes a barbed end for a push-on 3/8" rubber fuel line. The 325-8131 includes an aluminum fuel filter with a 40 micron filter element and -6 AN female inlet will accept an Edelbrock fuel line kit for a complete fuel-pump to carburetor plumbing solution. They are manufactured of chrome plated steel and include a 5/8" -20 threaded banjo bolt with gaskets.

    Fuel Line Kit Instruction Sheet (PDF)

  • Shotgun Bill Small Block Chevy Tunnel Ram Kit
    Shotgun Bill Small Block Chevy Tunnel Ram Kit
    x
                

    The Shotgun Bill® tunnel ram kit gives you two manual choke 500 cfm Edelbrock carbs, the famous Shotgun Bill® air scoop, carb linkage and Edelbrock street tunnel ram intake. (3500-7500 rpm)

    Designed for 302-327-350-400 c.i.d. small-block Chevy V8s operating below 7500 rpm where low-end torque is not a prime factor. Great for engines with slightly modified or aftermarket heads. Applicable to street machines, street rods, pro street and marine.

    Will NOT work with 1987-up cast iron heads or HEI distributors. See Notes tab for important install notes.

    925-19905 Instructions (PDF)

  • Speedway Steel 5/8 Inch LH Male Heim Joint Rod Ends with Stud
    Speedway Steel 5/8 Inch LH Male Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • Speedway Steel 5/16 Inch LH Male Heim Joint Rod Ends with Stud
    Speedway Steel 5/16 Inch LH Male Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • Speedway Steel 3/8 Inch LH Female Heim Joint Rod Ends with Stud
    Speedway Steel 3/8 Inch LH Female Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • Speedway Steel 1/2 Inch RH Female Heim Joint Rod Ends with Stud
    Speedway Steel 1/2 Inch RH Female Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of. They are Teflon lined and the RH thread stud has a hex built in for easy installation. 
            
  • Speedway Steel 1/4 Inch LH Male Heim Joint Rod Ends with Stud
    Speedway Steel 1/4 Inch LH Male Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • Speedway Steel 3/16 Inch RH Female Heim Joint Rod Ends with Stud
    Speedway Steel 3/16 Inch RH Female Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of. They are Teflon lined and the RH thread stud has a hex built in for easy installation. 
            
  • Speedway Steel 3/8 Inch LH Male Heim Joint Rod Ends with Stud
    Speedway Steel 3/8 Inch LH Male Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • Speedway Steel 7/16 Inch RH Female Heim Joint Rod Ends with Stud
    Speedway Steel 7/16 Inch RH Female Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of. They are Teflon lined and the RH thread stud has a hex built in for easy installation. 
            
  • Speedway Steel 1/2 Inch LH Male Heim Joint Rod Ends with Stud
    Speedway Steel 1/2 Inch LH Male Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of.  They are teflon lined.
            
  • Speedway Steel 1/4 Inch RH Female Heim Joint Rod Ends with Stud
    Speedway Steel 1/4 Inch RH Female Heim Joint Rod Ends with Stud
    x
                These rod ends make it easy to build carb or shift linkage, tie rod assemblies or anything else you can think of. They are Teflon lined and the RH thread stud has a hex built in for easy installation. 
            
Goto Previous PagePrevious Page
1 2