Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"carb intake" Page 1 of 8

  • Three Plain 9 Super 7   Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    Three Plain 9 Super 7 Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    x
                

    This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

    Kit includes three carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

    9 Super 7® Linkage Instructions (PDF)

    Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

    The 9Super7 Carb  makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both prima

  • Two Plain 9 Super 7   Carbs, Edelbrock 1103 Slingshot Intake, 1938-48 Ford V8
    Two Plain 9 Super 7 Carbs, Edelbrock 1103 Slingshot Intake, 1938-48 Ford V8
    x
                Please view the product's page for more information
            
  • Offenhauser 1075 1949-1953 Ford Flathead Regular Dual Intake Manifold
    Offenhauser 1075 1949-1953 Ford Flathead Regular Dual Intake Manifold
    x
                

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The generator may not fit into the stock location due to the clearance issue with the carburetor.  The generator can be relocated to the passenger side using bracket # 325-1146. If using a GM alternator, use our chrome 916-67909 or plain 916-67910 bracket.

    • Carb Centers:  4-3/4"
    • Carb pads are angled as they were on stock 49-53 intakes
    • Front drivers side accessory hole is for draft tube and measures 1.25"
    • Rear drivers side accessory hole is for oil fill tube and measures 1.375"
  • Two Plain 9 Super 7   Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    Two Plain 9 Super 7 Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    x
                

    This kit uses the Offy Dual '49-'53 Flathead Ford intake with Speedway's 9 Super 7® carbs. It includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. 

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb

  • Two Plain 9 Super 7   Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    Two Plain 9 Super 7 Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    x
                Please view the product's page for more information
            
  • Holley 2300 to Rochester 2G Two Barrel Intake Carburetor Adapter
    Holley 2300 to Rochester 2G Two Barrel Intake Carburetor Adapter
    x
                

    This aluminum carb adapter plate lets you adapt a large Holley 2300 series 2-barrel carburetor to a Rochester 2G 4-bolt 2-barrel intake manifold base. The adapter features an open plenum design and measures 1/2" thick. The carburetor adapter includes two gaskets and all necessary hardware to install.

    • Adapts Holley 2300 (or equivalent Ford/Motorcraft) to Rochester 2G/Carter intake
    • Smaller bolt pattern: 1-7/8" x 3-1/4"
    • Larger bolt pattern: 3-1/2" x 5-1/8"
    • Adapter is 1/2" thick

    Note: With just a little work with a file, the adapter can also be used to adapt an intake manifold with a 2" x 3-3/4" bolt pattern to the Holley 2300/Ford/Motorcraft 2 barrel carburetor as well.

  • Offenhauser 1035 1950-1959 Chevy 6-Cylinder Dual Carb Intake Manifold
    Offenhauser 1035 1950-1959 Chevy 6-Cylinder Dual Carb Intake Manifold
    x
                

    Offenhauser Dual Carb intake manifolds provide a nostalgic appearance while equalizing fuel distribution to all cylinders, improving both performance and economy. With this lightweight cast aluminum manifold, your old "Stovebolt" will be more responsive across the RPM range. Use with two "big base" carburetors (2-15/16" bolt centers) typical of 1954-62 Chevys.

    • Fits 216-235-261 Chevy 6-cylinders
    • 1950-1959 engines w/ PowerGlide
    • 1953-1959 engines w/ Manual Transmission

     

    Included linkage kit is "non-progressive," meaning both carbs operate at the same time.

  • Chrome 9 Super 7   Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    Chrome 9 Super 7 Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    x
                

    This kit uses the Offenhauser Dual 1949-1953 Flathead Ford V8 intake with 9 Super 7® carbs. In includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required.

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7 Carb ® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7® in a 2x2 or 3x2

  • Professional Products Cyclone Small Block Chevy Intake Manifold
    Professional Products Cyclone Small Block Chevy Intake Manifold
    x
                

    The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds, not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally, each Power+Plus Manifold is 100% pressure tested for leaks to eliminate installation problems. This is our most popular manifold and is showing up on many performance street machines and street rods.

    RPM range is idle to 5500.  Availabe in plain or show polished.

    NOTES: Manifold includes adaptor bushings to also fit 1987-1995 iron or aluminum heads.  Polished intakes have EGR ports with block plates.

     

     

  • Edelbrock 2150 Small Block Chevy 6-Carb X1 Ram Log Intake Manifold
    Edelbrock 2150 Small Block Chevy 6-Carb X1 Ram Log Intake Manifold
    x
                

    These Edelbrock X1 manifolds are reproductions of the originals introduced in the 1950's for 283-327 small-block Chevy. This manifold features large free-flowing straight runners for six, 3-bolt carburetors such as our 9 Super 7. Oval carb opening measures 1.45” x 2.96”. Includes machined oil fill tube provision and period correct casting features for the best vintage look and performance for your small-block Chevy street rod application.

    • Exact reproduction of the original late 1950"s Edelbrock Ram manifold
    • Fits Chevy 283-327 engines
    • Uses six 3 bolt base carbs like 9 Super 7's, Stromburg 97 or Edelbrock 94's
    • 2500-7000 RPM
  • Chrome 9 Super 7   Carbs, Offy 1090 Regular Intake Manifold Kit, 32-48 Ford V-8
    Chrome 9 Super 7 Carbs, Offy 1090 Regular Intake Manifold Kit, 32-48 Ford V-8
    x
                Please view the product's page for more information
            
  • Chrome 9 Super 7   Carbs on Eddie Meyer Intake Manifold Kit, 1932-48 Ford V8
    Chrome 9 Super 7 Carbs on Eddie Meyer Intake Manifold Kit, 1932-48 Ford V8
    x
                

    This kit uses the Eddie Meyer Flathead Ford intake with 9 Super 7® carbs. It includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required.

    Eddie Meyer 32-48 Intake Manifold - 

    Eddie Meyer was a Flathead Ford genius, and you can take advantage of his knowledge and experience with this dual-carb intake reproduced from the original tooling. This short-runner, non-heated manifold fits 1932-1948 Flathead Ford and Mercury V8s.

    • Short, high-flow runners
    • Non-heated design
    • Requires offset generator mounting
    • 8-1/4" carb centers
    • Overall Height:  2-1/2" (from block mount to carb base)

    9 Super 7® Primary Carbs -

    Speedway Motors has incorporated many improvements in the 9Super7 Carb while maintaining the Stromberg 97 carburetor's original look. Features such as the choke assembly, accelerator pump, main jets and cos

  • Chrome 9 Super 7   Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    Chrome 9 Super 7 Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    x
                Please view the product's page for more information
            
  • Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most. Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains.

    325-27014 Instructions (PDF)

  • Edelbrock 2101 Performer 1955-86 Small Block Chevy Intake Manifold
    Edelbrock 2101 Performer 1955-86 Small Block Chevy Intake Manifold
    x
                

    Edelbrock's famous Performer manifold is designed for street 1955-86 small block Chevys. This manifold is a stock replacement/street legal part for 302/327/350 V8s with OEM 4 bbl. or Edelbrock Performer Series carbs. Will also work on 1966-72 (1973 non-California) cars, 1966-83 trucks and Suburbans; except stock equipped EGR.

    Performers accept late-model choke, waterneck, air-conditioning, alternator and H.E.I. Not for 1987 and later cast iron or Chevy Bowtie heads. Will fit 1987 and later stock aluminum heads. 

    Made in the U.S.A. 

    325-2101 Instructions (PDF)

    NOTE: This intake does not work with kickdown kit 491-2350U.

  • Plain 9 Super 7   Carbs on Eddie Meyer Intake Manifold, 1932-48 Ford V8
    Plain 9 Super 7 Carbs on Eddie Meyer Intake Manifold, 1932-48 Ford V8
    x
                Please view the product's page for more information
            
  • Two Plain 9 Super 7   Carbs on Single 4 Barrel Intake Manifold Adapter Kit
    Two Plain 9 Super 7 Carbs on Single 4 Barrel Intake Manifold Adapter Kit
    x
                Please view the product's page for more information
            
  • Three Plain 9 Super 7   Carbs on an Edelbrock 1109 Intake, 1949-53 Ford V8
    Three Plain 9 Super 7 Carbs on an Edelbrock 1109 Intake, 1949-53 Ford V8
    x
                Please view the product's page for more information
            
  • Three Chrome 9 Super 7   Carbs, 1957-86 Small Block Chevy Edelbrock Intake
    Three Chrome 9 Super 7 Carbs, 1957-86 Small Block Chevy Edelbrock Intake
    x
                

    This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

    Kit includes three chrome plated carbs, the plain finish aluminum intake, 4" chrome air cleaners, linkage kit, chrome fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

    9 Super 7® Linkage Instructions (PDF)

    Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

    The 9Super7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carbure

  • Plain 9 Super 7   Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    Plain 9 Super 7 Carbs on Eddie Meyer Intake Manifold Kit, 1949-53 Ford V8
    x
                

    This kit uses the Eddie Meyer Flathead Ford intake with Speedway's 9 Super 7 ® carbs. It includes two 9Super7 carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line.   The assembled height on this is 16.25".  Assembly required. 

    9 Super 7 ® Linkage Instructions (PDF)

    Eddie Meyer 49-53 Intake Manifold - 

    These Eddie Meyer intake manifolds are reproduced from the original tooling. This '49-'53 Ford version is a 2-piece, long runner, exhaust heated manifold that is better suited to street use.

    • Precision cast and machined aluminum 
    • Works with stock generator/mount (and aftermarket brackets)
    • 4-3/4" carb centers
    • Provisions for original draft tube and oil filler
    • Accepts common 3-bolt carburetors
    • Overall Height:  7-1/2"
    • Draft Tube Hole:  1.25"
    • Oil Filler Tube Hole:  1.39"

    9 Super 7® Primary Carbs -

    Speedway Motors has incorporated many improvements in the 9 Super 7® while maintaining the Stromberg 97 carburetor's original l

  • Two Plain 9 Super 7   Carbs, Offenhauser 1076 Super Intake Kit, 1949-53 Ford V8
    Two Plain 9 Super 7 Carbs, Offenhauser 1076 Super Intake Kit, 1949-53 Ford V8
    x
                Please view the product's page for more information
            
  • Three 2 Barrel Carbs to 4 Barrel Intake Adapter
    Three 2 Barrel Carbs to 4 Barrel Intake Adapter
    x
                

    Want the race-ready looks of a tri-power setup but don't want to buy a new manifold?  Adapter that allows you to put three two barrel carbs on a four barrel intake. Accepts vintage 3-bolt Stromberg, Ford, and Holley carbs as well as the Demon 98 and Speedway 9 Super 7.

    Use linkage kit 135-6714 with Demon 98.

    Use linkage kit 135-6715 with others.

  • Offenhauser 1077 1949-1953 Ford Flathead Triple Carb Intake Manifold
    Offenhauser 1077 1949-1953 Ford Flathead Triple Carb Intake Manifold
    x
                This Offy 3x2 tri power manifold is designed for Stromberg 97 carbs ONLY. Manifold has 4-5/8" carb centers.  The front of the intake manifold has the  boss or flange for the generator or fan assembly to mount to. It also  has the fill and draft holes behind this flange.
    • For 1949-53 Ford Flatheads
    • 4-5/8" carb centers
    • Three Deuce carburetor style
    • Has boss or flange for generator or fan assembly to mount to
    • Has the fill and draft holes behind flange
    • Generator adapter bracket NOT included

    Manifold includes: 

    • 1.375" hole in the front of the intake for an oil-fill or breather tube
    • 1.25" hole in the front of the intake for the road draft tube

    Note: We recommend our Offenhauser 1949-1953 Flathead Intake Gasket for use with these intake manifolds.

  • Edelbrock 1103 1938-48 Ford/Mercury Flathead Slingshot Manifold, Two Carb
    Edelbrock 1103 1938-48 Ford/Mercury Flathead Slingshot Manifold, Two Carb
    x
                

    Edelbrock has decided to re-release this legendary manifold; giving a new generation a chance to own this historic benchmark. Using a pair of two barrel carburetors mounted in a "Y" configuration, this manifold unlocked the potential of Ford's versatile flathead platform for thousands of enthusiasts across the country. The Slingshot manifold is designed for use with 1938-48 style Flatheads, some late model blocks can be modified to work with these heads. It works with standard three bolt Stromberg, Holley and Demon carburetors and allows for the use of a period correct generator mounted in the stock location. 7-3/4" tall. 

    This is a reproduction of the original intake manifold designed by Vic Edelbrock Sr. in 1938. The Slingshot is a real show stopper and even includes stainless acorn nuts for mounting the two halves.  Among the first ever hot rod parts, the famous Edelbrock Slingshot still ranks among the best flathead intakes out there. The Slingshot produces more peak torque than the competitors two carb intakes, as well as more overall average power and torque. The ’38-vintage, two-piece Slingshot more than holds its own even today. If you want a high-rise, Edelbrock’s design is far superior. Includes assembly hardware and gasket #8700.  

    • For 1938-48 Ford/Mercury Flathead
    • Includes assembly hardware and gasket
    • 7-3/4" tall
    • Made in the USA
Goto Previous PagePrevious Page
1 2 3 4 5 ... 8