Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"brake rotor" Page 1 of 25

  • Speedway Pro-Lite Vented Brake Rotor, 11.75 x .81 Inch
    Speedway Pro-Lite Vented Brake Rotor, 11.75 x .81 Inch
    x
                

    Every rotor is cast from premium grade, long grain carbon iron which exhibits long wear, high thermal stability, and excellent resistance to distortion in high heat. Modern foundry and machining techniques hold close tolerances on face and vane thickness. Combining the correct face thickness with a 32 vane casting provides superior heat management and long service life with low rotating and unsprung weight. The straight vane design also makes it possible to use the same rotor on left or right hand mounting locations.

    • Thickness: GM .810"
    • Outside Diameter: 11.75"
    • # Holes: 8
    • Bolt Circle: 7"
    • Thread: Thru
    • Weight: 8.00 lbs

    Pro-Lite Rotor Application Chart (GIF)

  • Wilwood 150-8850 Poly-D 10 Double Quick Change Brake Pad
    Wilwood 150-8850 Poly-D 10 Double Quick Change Brake Pad
    x
                

    Double Quick-Change pads are compatible with our Wilwood Forged Dynalite and Billet Dynalite calipers.

    • Medium friction, low to medium temperarture range.
    • Good cold torque response.
    • Low to moderate wear rate

    Pads are sold each. (Will need 2 per caliper.)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brochure (PDF) 

    Brake Pad Brand Guide (Link)

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Mustang II Disc Brake Rotor, 5 on 4-3/4 Inch
    Mustang II Disc Brake Rotor, 5 on 4-3/4 Inch
    x
                Vented stock 9-1/4" diameter brake rotors for 1974-1980  Mustang II, Pinto, or Bobcat spindles (or Speedway brake kits using  '49-'54 Chevy spindles). Brake rotors are new, not plugged or re-drilled. Has a  5 on 4-3/4" bolt pattern with corresponding 7/16" diameter fine thread  wheel studs.

    Be sure to install new bearings and seals (910-31000) with your new disc brake rotors.
  • Speedway 338 Medium Double Quick Change Brake Pad
    Speedway 338 Medium Double Quick Change Brake Pad
    x
                

    Double Quick-Change pads are compatible with our Wilwood Forged Dynalite and Billet Dynalite calipers.

    Pads are sold each. (Will need 2 per caliper.)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link)

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Bearing-Seal Kit for Two Mustang II Brake Rotors
    Bearing-Seal Kit for Two Mustang II Brake Rotors
    x
                

    This bearing and seal kit includes two inner wheel bearings, two outer wheel bearings and two inner grease seals. This kit is enough for two brake rotors and is intended to be used with a new rotor installation as this kit does not include the bearing races or cups.

    If your project willl be making use of used rotors, you will require new bearing races or cups.  Therefore you will need to purchase the bearing and seal kit # 910-31052 suggested below in place of kit # 910-31000.

    Works with Mustang II/Pinto and Granada rotors using Mustang II/Pinto spindles only. It will not work for installing Mustang II/Pinto brake rotors on 1949-1954 Chevy spindles. Not for use with early Chevy spindle brake conversion kits.

    -Large Bearing-
    Thickness: .656"
    Upper OD: 1.900"
    Lower OD: 2.150"
    Bearing ID: 1.375"

    -Small Bearing-
    Thickness: .651"
    Upper OD: 1.380"
    Lower OD: 1.570"
    Bearing ID: 0.864"

    Never install new hubs with old bearings.

  • Speedway Pro-Lite Vented Brake Rotor, 11.75 x 1.25 Inch
    Speedway Pro-Lite Vented Brake Rotor, 11.75 x 1.25 Inch
    x
                

    Every brake rotor is cast from premium grade, long grain carbon iron which exhibits long wear, high thermal stability, and excellent resistance to distortion in high heat. Modern foundry and machining techniques hold close tolerances on face and vane thickness. Combining the correct face thickness with a 32 vane casting provides superior heat management and long service life with low rotating and unsprung weight. The straight vane design also makes it possible to use the same rotor on left or right hand mounting locations.

    • Thickness: GM 1.25"
    • Outside Diameter: 11.75"
    • # Holes: 8
    • Bolt Circle: 7"
    • Thread: Thru
    • Weight: 8.70 lbs

    Pro-Lite Rotor Application Chart (GIF)

  • Speedway 1978-88 GM Metric Brake Pad Spacer
    Speedway 1978-88 GM Metric Brake Pad Spacer
    x
                Use Speedway brake pad spacers with .810" rotors and stock-style 1978-1988 GM calipers. Spaces brake pad out .242" from caliper piston.
            
  • Hawk HB119M.594 Performance Black 1978-Up GM Metric Brake Pads
    Hawk HB119M.594 Performance Black 1978-Up GM Metric Brake Pads
    x
                

    Get superior stopping power with Hawk Performance! Hawk Performance brake pads have been successful in virtually all forms of motorsports for over 16 years. This success helps Hawk Performance enjoy the benefits of the “Win on Sunday, Sell on Monday,” philosophy. Hawk is one of few brake pad manufacturers that can deliver on the promise, “Race Proven – Street Legal.”

    Hawk Black Pads:

    Medium torque and temperature compound designed to be a good, all-purpose low- cost racing brake pad. Can be used as a Dirt Circle Track and Stock Car application.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Mustang II Disc Brake Rotor, 5 on 4-1/2 Inch
    Mustang II Disc Brake Rotor, 5 on 4-1/2 Inch
    x
                Vented stock 9-1/4" diameter brake rotors for 1974-1980  Mustang II, Pinto, or Bobcat spindles (or Speedway brake kits using  '49-'54 Chevy spindles). Brake rotors are new, not plugged or re-drilled. Has a  5 on 4-1/2" bolt pattern with corresponding 1/2" diameter fine thread  wheel studs. 

    Be sure to install new bearings and seals (910-31000) with your new disc brake rotors.
  • Wilwood 270-9761 Dynamic Brake Clamp, 6 x 5-1/2 Inch Bolt Pattern
    Wilwood 270-9761 Dynamic Brake Clamp, 6 x 5-1/2 Inch Bolt Pattern
    x
                

    Wilwood's Sprint inboard hub & adapter kit provides a basis to bolt dynamic rotor rotor mounting of standard 6 x 5.50" bolt pattern rotors. Contains rotor adapter and dynamic rotor mounting bolt kit. Made from high strength aluminum. It provides a lightweight and strong solution for rotor mounting. Weighs only 1.2 lbs.

    • Sprint Inboard
    • Sprint / Midget use only 
    • Material: Aluminum
    • Finish: Black Anodize
    • Weight: 1.2
    • Rotor Mount Bolt Circle (in.): 8 x 3.35
    • Mount Type: Adapter-Dynamic
    • Adapter bolt Circle (s) 6-Bolt Type: 6 x 5.50 in.

    Will clamp to a Winters axle and dynamic mount rotors.

  • Speedway 156 Hard Brake Pad
    $8.99
    Speedway 156 Hard Brake Pad
    x
                

    For Ultra Lite single piston floating caliper, Outlaw 1000 and Wilwood Dynalite Single.

    .450" thick, 1.97" long, 589 A Compound

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link)

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Speedway 338 Medium Brake Pad
    Speedway 338 Medium Brake Pad
    x
                

    For Ultra Lite single piston floating caliper, Outlaw 1000 and Wilwood Dynalite Single.

    .450" thick, 1.97" long, 589 A Compound

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link)

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Wilwood 160-0471 Ultralite Vented Brake Rotor, 11.75 x .81 Inch
    Wilwood 160-0471 Ultralite Vented Brake Rotor, 11.75 x .81 Inch
    x
                

    Every Wilwood brake rotor is cast from premium grade, long grain carbon iron. This material exhibits long wear, high thermal stability, and excellent resistance to distortion in high heat. Modern foundry and machining techniques hold close tolerances on face and vane thickness. Combining the correct face thickness with a 32 vane casting provides superior heat management and long service life with low rotating and unsprung weight. The straight vane design also makes it possible to use the same rotor on left or right hand mounting locations.

    Ultralite Rotor Application Chart (GIF)

  • 1973-77 GM Midsize 11 Inch Brake Rotor, 5 on 5 Inch
    1973-77 GM Midsize 11 Inch Brake Rotor, 5 on 5 Inch
    x
                

    1973-1977 GM mid sized front brake rotor. 5 on 5" with 5/8" coarse studs installed. 11" diameter x 1".  IMCA Approved.

    This rotor is designed for dirt track applications and should NOT be used for asphalt racing.



     

  • Hex Brake Rotor Mounts, 1.05 Inch
    Hex Brake Rotor Mounts, 1.05 Inch
    x
                  Screws and spacers for mounting rotors to your sprint hubs.   
            
  • Speedway 10 Inch Hybrid Brake Rotor for Pinto
    Speedway 10 Inch Hybrid Brake Rotor for Pinto
    x
                

    5/8" Studs Installed - All coarse threads are quick start style. 

    Our new 10" hybrid rotor is designed to fit the Pinto spindle. Complete with inner and outer races and 5/8" studs. Pre-drilled holes include 5 on 5" bolt circle spacing.

    This brake rotor is designed for dirt track applications and should NOT be used for asphalt racing.

     

  • Hybrid Brake Rotor Conversion Kit
    Hybrid Brake Rotor Conversion Kit
    x
                

    This kit is for you guys already running Pinto spindles but want to swap out your heavy Granada rotors for the lighter Hybrids. Re-use your metric calipers. 5 x 5" bolt pattern.

    • Two new IMCA approved 10" hybrid rotors
    • Left hand and right hand hybrid caliper brackets
    • Hardware
    • Four new wheel bearings
    • Two seals
    • Two new dust caps

    This brake kit is designed for dirt circle track applications only. It is not to be used for asphalt, pavement, or drag racing applications.

  • Wilwood 150-2390 Gator Brake Pad
    Wilwood 150-2390 Gator Brake Pad
    x
                

    For Ultra Lite single piston floating caliper, Outlaw 1000 and Wilwood Dynalite Single.

    • .450" thick, 1.97" long, 589 A Compound
    • Medium friction, low to medium temperarture range.                       
    • Good cold torque response.
    • Low to moderate wear rate

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brochure (PDF) 

    Brake Pad Brand Guide (Link)

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Deluxe Disc Brake Kit, 1955-1964 Chevy Full-size Car, Stock Spindle
    Deluxe Disc Brake Kit, 1955-1964 Chevy Full-size Car, Stock Spindle
    x
                

    These kits allow you to mount front disc brakes on your 1955-1964 Chevy full-size car (Bel-Air, Biscayne, Impala, 150 Series, 210 Series). Front disc brakes provide a significant improvement in braking performance versus the drum brakes your old Chevy came with. This disc brake kit works with stock, drum brake spindles only - it does not work with 2" drop spindles. Kit will work with 14" wheels intended for disc brake applications, as well as most 15" (or larger) wheels.

    Rotors are 11" diameter with 5 on 4-3/4" bolt pattern and calipers have 7/16"-20 inlets. This kit will increase track width 7/8" per side or 1-3/4" total when installed. 

    • 11" Rotors
    • 5 on 4-3/4" - bolt pattern
    • Metric calipers
    • Calipers mount behind axle (rearward)
    • Will work with 14" & larger wheels intended for use with disc brakes
    • Bearings, pads, brackets included
    • Seals and hoses
    • Hardware included
    • Increases trac-width 7/8" per side
    • For '55-'64 Chevy fullsize cars. 

    910-31911 Instructions (PDF)

     

  • Speedway Soft Street Brake Pads, GM Metric 1978-UP
    Speedway Soft Street Brake Pads, GM Metric 1978-UP
    x
                

    Speedway soft brake pad for GM Metric 1978-Up.

    Sold as one set of 4 (ST); outfits two calipers.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Speedway 156 1978-Up GM Metric Brake Pads
    Speedway 156 1978-Up GM Metric Brake Pads
    x
                

    The Speedway 156 brake pad works with aluminum or steel rotors. Best pad for aluminum rotors. Features a low metallic compound for long life and excellent street performance.

    Sold as one pair (PR); outfits one caliper.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Replacement 11-1/4 Inch Rear Brake Rotor
    Replacement 11-1/4 Inch Rear Brake Rotor
    x
                

    These 11-1/4" one-piece, vented iron disc brake rotors are for rear disc brake applications. Features dual bolt patterns for 5 x 4.5" (Ford/Mopar) and 5 x 4.75" (Chevy/GM) wheels. 

    • Center Hole:  2.78"
    • Backspace:  2.30"
    • Maximum Axle Flange Diameter:  6-1/4"
    • Thickness:  1"
    • Thickness @ Center of Rotor:  0.236"
  • Wilwood 150-8936K BP-10 GM Metric 1978-Up Brake Pads
    Wilwood 150-8936K BP-10 GM Metric 1978-Up Brake Pads
    x
                

    Speedway Motors is your one-stop shop for GM 1978-Up Midsize caliper brake pads.

    • Medium friction, smooth engagement, low abrasion on iron rotors.
    • Flat torque curve.
    • Low to medium wear rate, increases as temperature increases.

    Brake Pad Brochure (PDF)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side. 

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Speedway 1979-Up GM Metric Brake Rotor
    Speedway 1979-Up GM Metric Brake Rotor
    x
                

    This 1979-up GM Metric front disc brake rotor will work with a Set # 6 inner bearing/race which fits most spindles. 5 on 5" with 5/8" coarse studs installed. 10.5" diameter x 1".  Must be used with 912-TS3 outer bearings for 1982-1987 spindle applications.  IMCA Approved.

    This is a 1979-1981 Metric GM rotor with the bolt pattern changed to 5 on 5". It can be used on 1982-1987 GM metric spindles if the you use our bearing/seal kit 91031048, or use at least the 1979-1981 style outer bearing 912TS3.

    This rotor is designed for dirt track applications and should NOT be used for asphalt racing.




     

  • Wilwood 150-2391 Gator Double Quick Change Brake Pad
    Wilwood 150-2391 Gator Double Quick Change Brake Pad
    x
                

    Double Quick-Change pads are compatible with our Wilwood Forged Dynalite and Billet Dynalite calipers.

    • Medium friction, low to medium temperarture range.
    • Good cold torque response.
    • Low to moderate wear rate

    Pads are sold each. (Will need 2 per caliper.)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brochure (PDF) 

    Brake Pad Brand Guide (Link)

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Wilwood 120-9689 Billet Dyna Pro Single Caliper, 3-3/4 Inch Mount
    Wilwood 120-9689 Billet Dyna Pro Single Caliper, 3-3/4 Inch Mount
    x
                

    The Dyna Pro Single (DPS) billet caliper is the newest generation of calipers available as an upgrade or replacement for applications previously using the Dynalite Single (DLS) series. DPS calipers combine superior strength with performance enhancements to make these the best "Dyna" series calipers ever.

    The DPS is loaded with exclusive Wilwood performance enhancements. The calipers feature Quick-E-Clip pad retainers that support a 6812 type brake pad from the top. In addition to past pad service without caliper removal, the feature provides substantially stronger retention over the single Quick-Clip pin and 7012 type pads used in the previous DLS models.

    • Quick-E-Clip pad retainers supports brake pad from top
    • Heavy wall stainless steel pistons
    • Stainless steel SRS bridge plates eliminate pad rattle and dampen vibration
    • Internal fluid passages
    • Four corner bleed screws allow mounting in any front, rear, left, or right side position

     

  • Wilwood 15B-9819 Poly-B 10 Brake Pad
    Wilwood 15B-9819 Poly-B 10 Brake Pad
    x
                

    For Ultra Lite single piston floating caliper, Outlaw 1000 and Wilwood Dynalite Single.

    • .450" thick, 1.97" long, 589 A Compound
    • Medium friction, low to medium temperarture range.                       
    • Good cold torque response.
    • Low to moderate wear rate

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brochure (PDF) 

    Brake Pad Brand Guide (Link)

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
    11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
    x
                This rotor allows the use of GM Metric calipers along with a GM car bolt pattern. Vented stock 11" diameter brake rotors for 1974-1980  Mustang  II, Pinto, or Bobcat spindles (or popular GM Metric calipers and brackets). Brake rotors are new, not plugged or re-drilled. Has a   5 on 4-3/4" bolt pattern with corresponding 7/16" diameter fine thread   wheel studs.
    • 5 on 4.75" Bolt circle
    • Granada type rotor
    • For use with popular GM Metric calipers and brackets
    • Bearing and seal kit sold separately (910-31052)
  • AFCO 9850-6505 10 Inch Hybrid Brake Rotor for Pinto
    AFCO 9850-6505 10 Inch Hybrid Brake Rotor for Pinto
    x
                

    This brake rotor combines the strength of a '75-'81 Ford-style hub (Granada) with the lighter design of the metric brake rotor for an unbeatable lightweight and durable package.  AFCO engineers designed this rotor with the latest CAD software and testing methods.  Manufactured to withstand rigorous racing environments, the AFCO Hybrid Rotor uses totally new castings designed and built specifically for racing.  It will remove up to 12 lbs. of sprung weight on the front of your car to improve front to rear weight bias and wheel control.

    • Uses GM metric caliper
    • Ford '74-'80 Pinto Spindle
    • Strong and Lightweight
    • Safely remove up to 13 lbs from the front of your car vs stock rotor
    • 14.8# total rotor weight with 5/8" studs
    • 10.13" diameter
    • .813" thickness (pad spacer recommended)

    Instructions (PDF) 

  • GN Brake Adpt Plate 8-7"BC
    $34.99
    GN Brake Adpt Plate 8-7"BC
    x
                Fits 8 bolt on 7" center rotors.  For use on GN rear hub, 910-48351-DIR, to permit attachment of brake rotors.
            
  • Rotor-Hat Bolt Set
    $3.99
    Rotor-Hat Bolt Set
    x
                Ultralight, 5/16-24 thread. Set of 8. With self-locking nuts.
            
  • Speedway Cast Iron Drilled Scalloped Brake Rotor, 11.75 x .810 Inch
    Speedway Cast Iron Drilled Scalloped Brake Rotor, 11.75 x .810 Inch
    x
                

    These scalloped iron brake rotors provide effective lightweight options for sprints, late models, modifieds, and other competition applications that race in low to medium temperature ranges. Steel rotors are typically found in lighter weight open wheel cars such as sprints and modifieds.  Speedway's premium 11.75" x .810" drilled scalloped brake rotor weighs only 5.07 lbs.

    • Scallop configuration provides greatest weight reduction on a vented straight vane iron rotor
    • Scallop machining removes as much as three pounds, or nearly 33% of the rotor mass
    • Vented castings provide increased cooling capacity over machined steel plate rotors
    • Improved structural durability over drilled rotor designs
    • Vented iron 
    • Inboard mounted (Sprints)

    Note: Suitable for Light Dirt Racing applications. Scalloped Rotors are unsafe for street use.


     

  • Lokar BAG-6099 1967-69 Camaro/Firebird E-Brake Pedal Pad
    Lokar BAG-6099 1967-69 Camaro/Firebird E-Brake Pedal Pad
    x
                These billet aluminum pads are the perfect finishing touch for your dream car. The pedal pads attach to your existing brake pedals. 
            
  • Ford 9 Inch Bolt-On Rear Disc Brake Kit
    Ford 9 Inch Bolt-On Rear Disc Brake Kit
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM metric style calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31902 Instructions (PDF)

  • Wilwood 150-9753K High-Temperature Racing Brake Pads, Composite Metallic
    New
    Wilwood 150-9753K High-Temperature Racing Brake Pads, Composite Metallic
    x
                

    These metallic composite racing pads feature a medium-high temp range similar to full metallic, medium-high torque.

    • High friction throughout temperature range, high temperature range
    • Formulation specific for use with Super Alloy rotors
    • Pad thickness: .60"

    Composite Metallic: Application:

    • Narrow Dynalite caliper application
    • Race ONLY compound for specialty alloy rotors such as titanium and light weight steel
    • Sprint cars with titanium rotors, speedway cars with plate steel rotors, and other specialized vehicles where high temperature fade and wear resistance are necessary to offset diminished cooling capacity due to rotor material and configuration

    Composite Metallic: Characteristics:

    • Medium to high friction compound with a steadily increasing torque curve as temperatures rise
    • Good wear and friction properties with high fade resistance for special applications where intermittent high temperature spikes are observed between periods of moderate temperature braking 

    Note: Temperature range and overall friction value are the primary considerations for pad selection. The pads must be capable of maintaining the proper amount of friction for stopping power within the temperatures that will be realized on the track during

  • Wilwood 15E-6103K Poly-E GM Metric 1978-Up Brake Pads
    Wilwood 15E-6103K Poly-E GM Metric 1978-Up Brake Pads
    x
                

    Speedway Motors is your one-stop shop for GM 1978-Up Midsize caliper brake pads.

    Brake Pad Brochure (PDF)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side. 

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Wilwood 160-8135 Scalloped Brake Rotor, 11.75 x .81 Inch
    Wilwood 160-8135 Scalloped Brake Rotor, 11.75 x .81 Inch
    x
                

    When it comes to brake rotors, racers are constantly searching for the ultimate balance between the lowest weight and the ability to effectively manage heat. Decreased rotating weight in the drive line provides quicker deceleration under braking and quicker acceleration out of the corners. Lower weight also benefits handling with improved spring and shock control over the unsprung suspension mass. Wilwood's ULS-32 scalloped iron rotors provides effective lightweight options for sprints, late models, modifieds, and other competition applications that race in low to medium temperature ranges.

    Note: Suitable for Light Dirt Racing applications. Scalloped Brake Rotors are unsafe for street use.

    • Scallop configuration provides greatest weight reduction on a vented straight vane iron rotor
    • Scallop machining removes as much as three pounds, or nearly 33% of the rotor mass
    • Vented castings provide increased cooling capacity over machined steel plate rotors
    • Improved structural durability over drilled rotor designs
    • Thread: Thru

    Rotor Application Chart (GIF)

     

    Proper Break-In Procedure for Steel or Cast Iron Rotors

    New steel/i

  • Speedway 338 Medium Superlite Brake Pad
    Speedway 338 Medium Superlite Brake Pad
    x
                

    Replacement brake pads for your Wilwood Superlite or Ultra Lite 300 Series calipers. 

    • Width 4.74"

    Pads are sold individually.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Speedway Cast Iron Scalloped Brake Rotor, 11.75 x .810 Inch
    Speedway Cast Iron Scalloped Brake Rotor, 11.75 x .810 Inch
    x
                

    Speedway's premium 32 Vane scalloped cast iron brake rotors weigh only 5.58 lbs.

    • Vented iron 
    • Bolt Circle: 8 x 7"
    • Threads:  Thru
    • Face: scalloped
  • Speedway Cast Iron Scalloped Brake Rotor - 11.75 x 1.25 Inch
    Speedway Cast Iron Scalloped Brake Rotor - 11.75 x 1.25 Inch
    x
                Speedway's premium 32 Vane scalloped cast iron brake rotors weigh only 6.36 lbs.
            
Goto Previous PagePrevious Page
1 2 3 4 5 ... 25