Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"brake mustang ii" Page 1 of 4

  • Mustang II Disc Brake Rotor, 5 on 4-3/4 Inch
    Mustang II Disc Brake Rotor, 5 on 4-3/4 Inch
    x
                Vented stock 9-1/4" diameter brake rotors for 1974-1980  Mustang II, Pinto, or Bobcat spindles (or Speedway brake kits using  '49-'54 Chevy spindles). Brake rotors are new, not plugged or re-drilled. Has a  5 on 4-3/4" bolt pattern with corresponding 7/16" diameter fine thread  wheel studs.

    Be sure to install new bearings and seals (910-31000) with your new disc brake rotors.
  • Bearing-Seal Kit for Two Mustang II Brake Rotors
    Bearing-Seal Kit for Two Mustang II Brake Rotors
    x
                

    This bearing and seal kit includes two inner wheel bearings, two outer wheel bearings and two inner grease seals. This kit is enough for two brake rotors and is intended to be used with a new rotor installation as this kit does not include the bearing races or cups.

    If your project willl be making use of used rotors, you will require new bearing races or cups.  Therefore you will need to purchase the bearing and seal kit # 910-31052 suggested below in place of kit # 910-31000.

    Works with Mustang II/Pinto and Granada rotors using Mustang II/Pinto spindles only. It will not work for installing Mustang II/Pinto brake rotors on 1949-1954 Chevy spindles. Not for use with early Chevy spindle brake conversion kits.

    -Large Bearing-
    Thickness: .656"
    Upper OD: 1.900"
    Lower OD: 2.150"
    Bearing ID: 1.375"

    -Small Bearing-
    Thickness: .651"
    Upper OD: 1.380"
    Lower OD: 1.570"
    Bearing ID: 0.864"

    Never install new hubs with old bearings.

  • Mustang II Disc Brake Rotor, 5 on 4-1/2 Inch
    Mustang II Disc Brake Rotor, 5 on 4-1/2 Inch
    x
                Vented stock 9-1/4" diameter brake rotors for 1974-1980  Mustang II, Pinto, or Bobcat spindles (or Speedway brake kits using  '49-'54 Chevy spindles). Brake rotors are new, not plugged or re-drilled. Has a  5 on 4-1/2" bolt pattern with corresponding 1/2" diameter fine thread  wheel studs. 

    Be sure to install new bearings and seals (910-31000) with your new disc brake rotors.
  • Mustang II Complete 11 Inch Brake Kit, Ford 5 x 4-1/2 Bolt Pattern
    Mustang II Complete 11 Inch Brake Kit, Ford 5 x 4-1/2 Bolt Pattern
    x
                Upgrade your Mustang II based suspension from the stock 9-1/4" rotors to our 11" rotors with powerful single piston GM metric floating calipers. This simple bolt-on conversion requires no machining. For use on 1974-80 Pinto, Bobcat and Mustang II spindles.

    Features a 5 on 4-1/2" Ford/Mopar wheel bolt pattern (increases track width 1/2" per side). Includes two 16" front brake hoses and 7/16"-20 banjo bolts with crush washers.

    910-31944 Instructions (PDF)

  • 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
    11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
    x
                This rotor allows the use of GM Metric calipers along with a GM car bolt pattern. Vented stock 11" diameter brake rotors for 1974-1980  Mustang  II, Pinto, or Bobcat spindles (or popular GM Metric calipers and brackets). Brake rotors are new, not plugged or re-drilled. Has a   5 on 4-3/4" bolt pattern with corresponding 7/16" diameter fine thread   wheel studs.
    • 5 on 4.75" Bolt circle
    • Granada type rotor
    • For use with popular GM Metric calipers and brackets
    • Bearing and seal kit sold separately (910-31052)
  • Chevy Front Axle Steering & Brake Kit, 48 Inch Axle
    Chevy Front Axle Steering & Brake Kit, 48 Inch Axle
    x
                Please view the product's page for more information
            
  • Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    x
                Please view the product's page for more information
            
  • Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-1/2
    Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-1/2
    x
                

    An economical, lightweight brake kit for 1949-54 Chevy car spindles. Your stock Chevy spindles must be machined, or use Speedway '49-'54 Chevy-style spindles. This kit uses 9-1/4" Mustang II vented rotors with common GM metric calipers.

    • Typically used on Model T and Model A to 1936 Ford front ends 
    • For use on street rod tube front axles when using 1949-54 Chevy style spindles  
    • Will not work with stock 1949-54 steering arms 
    • Not to be installed on stock 1949-54 Chevy vehicle front ends

    910-31955 Instructions (PDF)

  • Mustang II IFS, Std. Tubular Control Arms, Stock Springs, Dropped Spindles
    Mustang II IFS, Std. Tubular Control Arms, Stock Springs, Dropped Spindles
    x
                Includes standard upper and offset strutless lower control arms, 2" dropped spindles, rubber brake lines, new black stock type springs and  shocks, new manual or rebuilt power rack & pinion with bushings and  new tie rods. The 11" brake kit features GM Metric calipers, with your  choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Stock Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-

  • Mustang II Tubular Lower Arms for Air Ride/Wilwood Brakes, No Strut Rod
    Mustang II Tubular Lower Arms for Air Ride/Wilwood Brakes, No Strut Rod
    x
                Please view the product's page for more information
            
  • Basic Brake Kit, GM Metric Caliper/Mustang II Rotor to Early Chevy Spindle
    Basic Brake Kit, GM Metric Caliper/Mustang II Rotor to Early Chevy Spindle
    x
                

    An economical, lightweight front disc brake conversion kit for 1949-54 Chevy car spindles. This kit uses 9-1/4" Mustang rotors with the easy-to-find '78-'88 GM metric calipers. This basic kit includes caliper brackets and hardware.

    Note: Your spindles must be machined to accept this kit, or you can use Speedway modified reproduction forged spindles 916-32100. This kit will not work with stock 1949-54 steering arms. Not to be installed on stock 1949-54 Chevy vehicle front ends. To be used only on street rod tube or I-beam front axles when using 1949-54 Chevy spindles commonly used on Model T and Model A to 1936 Ford front ends.

    916-31950 Instructions (PDF)

  • Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    x
                

    Includes standard upper and offset strutless lower control arms, new standard spindles, rubber brake lines, new black stock type springs and shocks, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles, Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2&qu

  • Mustang II IFS, Narrow Arms, Air Ride, Dropped Spindles, Wilwood Brakes
    Mustang II IFS, Narrow Arms, Air Ride, Dropped Spindles, Wilwood Brakes
    x
                Hub-to-hub kit includes 5/8" narrower upper and offset strutless  lower  control arms, 2" dropped spindles, rubber brake lines, air ride  , new manual or rebuilt power rack & pinion with  bushings  and   new tie rods. The 10-3/4" Wilwood brake kit features GM  Metric calipers  with rubber  hoses, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt   pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Air Ride Suspension shocks
      • Rack and Pinion with bushings and tie rods
      • 10-3/4" Wilwood brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note:  OEM rubber brake hoses generally cannot be adapted to Wilwood calipers. The caliper inlet fitting is a 1/8-27 NPT. The preferred method is to use steel adapter fittings at the caliper, either straight, 45 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock.

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959

  • Brake Pads for Mustang II Caliper
    Brake Pads for Mustang II Caliper
    x
                

    Our street compound brake pads provide safe, quiet, and reliable performance. For Mustang II and Pinto calipers.

    Complete set of 4 pads (services 2 calipers).

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Mustang II IFS, Std. Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    Mustang II IFS, Std. Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    x
                Hub-to-hub kit includes standard upper and offset strutless lower control arms, new  standard spindles, rubber brake lines, air ride springs/shocks, new manual or rebuilt power rack & pinion with bushings and  new tie rods. The 10-3/4" Wilwood brake kit features GM  Metric calipers with rubber  hoses, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt  pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles
      • Air Ride Springs/Shocks
      • Rack and Pinion with bushings and tie rods
      • 10-3/4" Wilwood brake kit with GM Metric calipers
      • Choose 5 x 4-1/2" or 5 x 4-3/4" bolt pattern
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note:  OEM rubber brake hoses generally cannot be adapted to Wilwood calipers. The caliper inlet fitting is a 1/8-27 NPT. The preferred method is to use steel adapter fittings at the caliper, either straight, 45 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock.

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford P

  • Mustang II Complete 11 Inch Front Disc Brake Kit, 5 on 4-3/4 Granada Type Rotor
    Mustang II Complete 11 Inch Front Disc Brake Kit, 5 on 4-3/4 Granada Type Rotor
    x
                Easily upgrade your Mustang II based suspension from the stock 9-1/4"  rotors to 11" rotors with powerful single piston GM Metric style floating  calipers. Kit requires no machining. For use on 1974-1980 Pinto, Bobcat  and Mustang II factory spindles.  
    • GM bolt pattern 5 on 4-3/4" (increases track width 1/2" per side)
    • Includes two 16" front brake hoses and 7/16"-20 banjo bolts with crush washers
    • Granada style rotors

    Front Disc Brake Installation Instructions (PDF)

  • Mustang II IFS, Short Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    Mustang II IFS, Short Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    x
                

    Hub-to-hub kit includes 5/8" narrower upper and offset strutless lower control arms, new standard spindles, rubber brake lines, air ride , new manual or rebuilt power rack & pinion with bushings and new tie rods. The 10-3/4" Wilwood brake kit features GM Metric calipers with rubber hoses, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • New Standard Spindles
      • Air Ride Suspension shocks
      • Rack and Pinion with bushings and tie rods
      • 10-3/4" Wilwood brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note:  OEM rubber brake hoses generally cannot be adapted to Wilwood calipers. The caliper inlet fitting is a 1/8-27 NPT. The preferred method is to use steel adapter fittings at the caliper, either straight, 45 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock.

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Picku

  • Bearing & Seal Kit - 11 Inch Brakes to Mustang II Spindle
    Bearing & Seal Kit - 11 Inch Brakes to Mustang II Spindle
    x
                Bearing & seal kit for GM 11" rotor/Mustang II spindle brake kit (910-31944)

    Kit Includes:

    • Seals
    • Tapered inner bearing cones
    • Tapered inner bearing cups
    • Tapered outer bearing cones
    • Tapered outer bearing cups
  • Mustang II IFS, Std. Control Arms, Air Ride, Dropped Spindles, Wilwood Brakes
    Mustang II IFS, Std. Control Arms, Air Ride, Dropped Spindles, Wilwood Brakes
    x
                Hub-to-hub kit includes standard upper and offset strutless lower  control arms, new 2"  dropped spindles, rubber brake lines, air ride  springs/shocks, new manual or rebuilt power rack & pinion with  bushings and  new tie rods. The 10-3/4" Wilwood brake kit features GM   Metric calipers with rubber  hoses, with your choice of 5 x 4-1/2" or 5 x  4-3/4" bolt  pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New 2" Dropped Spindles
      • Air Ride Springs/Shocks
      • Rack and Pinion with bushings and tie rods
      • 10-3/4" Wilwood brake kit with GM Metric calipers
      • Choose 5 x 4-1/2" or 5 x 4-3/4" bolt pattern
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note:  OEM rubber brake hoses generally cannot be adapted to Wilwood calipers. The caliper inlet fitting is a 1/8-27 NPT. The preferred method is to use steel adapter fittings at the caliper, either straight, 45 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock.

    Note:  If using these kits with Speedway or Heidts crossm

  • Mustang II Disc Brake Kit for Early Chevy Spindles, 5 on 4-1/2 Inch
    Mustang II Disc Brake Kit for Early Chevy Spindles, 5 on 4-1/2 Inch
    x
                

    This complete brake and hub kit is designed to install 1974-80 Mustang II/Pinto rotors and calipers onto your machined Chevy 1949-54 car spindles. Disc brake kit is desigend for use only on street rod tube front axles when using 1949-54 Chevy style spindles intended for Model T and Model A to 1936 Ford front ends. This kit includes two 9-1/4" rotors with a Ford bolt pattern.

    • 9-1/4" brake rotor, 5 x 4-1/2" wheel bolt pattern
    • Pinto/Mustang iron calipers, 7/16"-24 inlet
    • 16" rubber brake lines
    • Zinc plated dust caps
    • All necessary brackets, adapters, bearings, seals, and hardware
    • Instructions included

    Note: Will not work with traditional style steering (no room for upper steering arm). Will not work with stock 1949-54 steering arms. Not to be installed on stock 1949-54 Chevy vehicle front ends.

    910-31947 Instructions (PDF)

  • Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-3/4
    Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-3/4
    x
                

    An economical, lightweight brake kit for 1949-54 Chevy car spindles. Your stock Chevy spindles must be machined, or use Speedway '49-'54 Chevy-style spindles. This kit uses 9-1/4" Mustang II vented rotors with common GM metric calipers.

    • Typically used on Model T and Model A to 1936 Ford front ends 
    • For use on street rod tube front axles when using 1949-54 Chevy style spindles  
    • Will not work with stock 1949-54 steering arms 
    • Not to be installed on stock 1949-54 Chevy vehicle front ends

    910-31956 Instructions (PDF)

  • Mustang II Complete 11 Inch Front Disc Brake Kit, 5 x 4-3/4 GM Bolt Pattern
    Mustang II Complete 11 Inch Front Disc Brake Kit, 5 x 4-3/4 GM Bolt Pattern
    x
                Easily upgrade your Mustang II based suspension from the stock 9-1/4" rotors to 11" rotors with powerful single piston GM midsize floating calipers. Kit requires no machining. For use on 1974-1980 Pinto, Bobcat and Mustang II factory spindles.  

    GM bolt pattern 5 on 4-3/4" (increases track width 1" per side). Includes two 16" front brake hoses and 7/16"-20 banjo bolts with crush washers.

    910-31943 Instructions (PDF)

  • Mustang II Brake Kits for Early Chevy Spindles, GM 4.75 Pattern
    Mustang II Brake Kits for Early Chevy Spindles, GM 4.75 Pattern
    x
                

    This complete brake and hub kit is designed to install 1974-80 Mustang II/Pinto 9-1/4" rotors and calipers onto your machined Chevy 1949-54 car spindles.

    Kit features:

    • 9-1/4" brake rotor, 5 x 4-3/4" wheel bolt pattern
    • Remanufactured Pinto/Mustang iron calipers, 7/16"-24 inlet
    • 16" rubber brake lines
    • Zinc plated dust caps
    • All necessary brackets, adapters, bearings, seals, hardware and instructions included

    Note:

    • Will not work with traditional style steering (no room for upper steering arm).
    • Will not work with stock 1949-54 steering arms. Not to be installed on stock 1949-54 Chevy vehicle front ends.
    • For use only on street rod tube or I-beam front axles when using 1949-54 Chevy style spindles intended for Model T and Model A to 1936 Ford front ends.

    910-31948 Instructions (PDF)

  • 1932 Lo-Boy Front Disc Brake Kit
    1932 Lo-Boy Front Disc Brake Kit
    x
                

    This brake kit includes Mustang II/Pinto brake components to fit the '32 Lo-Boy 1949-54 Chevy spindles. Kit features 9-1/4" iron rotors, rebuilt single piston calipers, pads, stainless braided AN 4 brake lines, fittings, & hardware.

    NOTE: Kit includes rotors with 5 on 4.5" bolt pattern. If you need the 5 on 4.75" bolt pattern, please specify this in the Comments box on the Order Summary/Payment Info page (page 2) when checking out.

     

  • Wilwood 140-11017 Heavy Duty Front Brake Kit for Mustang II
    Wilwood 140-11017 Heavy Duty Front Brake Kit for Mustang II
    x
                

    Wilwood Forged Dynalite Front Pro Series Brake Kits offer a complete disc brake upgrade solution for Mustang II-equipped street rods and classic pickups. Based on the venerable forged billet 4-piston Dynalite caliper, these versatile kits suit the braking requirements and style preferences for a daily driver, serious competition, or the most discriminating show enthusiast. 

    Calipers mount directly to the spindle with a bolt-on aluminum bracket. Forged billet, five lug hubs with direct mount cast iron rotors combine to provide a significant weight savings compared to stock disc brakes. Kits include all new hardware, wheel bearings, seals, brake pads, brackets, and extra length lug studs.

    Aluminum hubs drilled to accept both 5-on-4-1/2" and 5-on-4-3/4" bolt patterns.

    Wilwood Medium Duty Kits Feature:

    • Forged 4-piston Dynalite Calipers
    • 11" diameter Ultralite HP 30 Vane rotors - bare finish
    • Wilwood BP-10 SmartPads - low noise, low dust
    • Lightweight clear anodized aluminum hubs

    835-1408652 Instructions (PDF)

    *NOTE*: See Notes tab for important install information.
  • SSBC Mustang II Competition Street Series 11 Inch Disc Brake Kit
    SSBC Mustang II Competition Street Series 11 Inch Disc Brake Kit
    x
                

    Bolt-in ultra high performance disc brake conversion kit for Mustang II. Kit includes street 4-piston aluminum calipers with 45mm stainless pistons, performance brake pads, mounting brackets, 11" Big Bite cross drilled rotors, and hardware.

    • 100% Made in the USA
    • Rotors are dual pattern - 5 on 4.5" & 5 on 4.75"
    • 15" wheel compatible
    • Calipers are constructed from 6061-T6 billet aluminum
    • Assembled with stainless steel pistons and bleeder screws
    • 25% more pad contact area than other calipers with this mount
    • 20% thicker pads than other calipers with this mount
    • Dual pad pin design with o-rings to eliminate pad chatter
    • Use any off-the-shelf D43 pad from any local parts store

    Calipers are available in plain finish (clear coated) billet, fully polished, red powder coat, or black powder coat.

  • Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    x
                Please view the product's page for more information
            
  • Wilwood 140-1013-B Drag Front Brake Kit for Mustang II
    Wilwood 140-1013-B Drag Front Brake Kit for Mustang II
    x
                

    Wilwood Forged Dynalite Front Drag Brake Kit offers a complete disc brake upgrade solution for Mustang II-equipped drag race application under 2800 lbs. Based on the venerable forged billet 4-piston Dynalite caliper, these versatile kits suit the braking requirements and style preferences for an off road drag racing application. 

    Calipers mount directly to the spindle with a bolt-on aluminum bracket. Forged billet, five lug hubs with direct mount steel rotors combine to provide an average weight savings of over 30 pounds compared to stock disc brakes. Kits include all new hardware, wheel bearings, seals, brake pads, brackets, and extra length lug studs.

    Aluminum hubs drilled to accept both 5-on-4-1/2" and 5-on-4-3/4" bolt patterns. 

    • Forged 4-piston Dynalite Calipers
    • 10.75" diameter solid steel rotors - black oxide finish
    • Wilwood BP-10 SmartPads - low noise, low dust
    • Lightweight clear anodized aluminum hubs

    835-1401013 Instructions (PDF)

  • Bearing & Seal Kit - GM 11 Inch Brakes to Mustang II
    Bearing & Seal Kit - GM 11 Inch Brakes to Mustang II
    x
                Bearing & seal kit for GM 11" Rotors (4.75" bolt pattern)/Mustang II spindle brake kit part 910-31943.  

    Kit Includes:

    • Seals
    • Tapered inner bearing cones
    • Tapered inner bearing cups
    • Tapered outer bearing cones
    • Tapered outer bearing cups
  • Speedway Mustang II Crossmember-Ford Frame-35-40 Car-35-41 Pickup-DLX
    Speedway Mustang II Crossmember-Ford Frame-35-40 Car-35-41 Pickup-DLX
    x
                Please view the product's page for more information
            
  • Mustang II IFS, Std. Tubular Control Arms, Coilover Springs, Stock Spindles
    Mustang II IFS, Std. Tubular Control Arms, Coilover Springs, Stock Spindles
    x
                Hub-to-hub kit includes standard upper and offset strutless lower control arms, new standard spindles, rubber brake lines, Carrera coilovers, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles
      • Coilover Springs
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2" frame widths, you w

  • 1974-80 Mustang II Brakes to 1949-54 Chevy Spindles, Polished Stainless
    1974-80 Mustang II Brakes to 1949-54 Chevy Spindles, Polished Stainless
    x
                

    Our basic front disc brake conversion kit is engineered to mount 1974-80 Pinto, Bobcat, and Mustang II 9-1/4" disc brakes onto 1949-54 Chevy passenger car spindles (some machining of spindles is necessary). Mounts the caliper behind the axle and allows a minimum 13" wheel diameter.

    • Caliper brackets
    • Bearings & seals
    • All hardware

    916-31905 Instructions (PDF)

    Learn more about selecting the proper master cylinder for your vehicle by reading our tech article. Brake System Selection

  • 1932 Lo-Boy Roadster Spindle Kit
    1932 Lo-Boy Roadster Spindle Kit
    x
                

    This kit mounts 1949-1954 Chevy spindles and Pinto/Mustang II disc brakes to your '32 Lo-Boy front axle.  Spindles are machined for Pinto/Mustang II 9-1/4" rotors. Kit includes spindles, kingpins, caliper brackets & hardware. 

    Kit includes:

    • (2) 49-54 Chevy spindles
    • (1) kingpin set
    • (1) Pinto rotor to Chevy spindle brake adapter kit
    • (2) Set screws, 1/4" UNC
    • (1) Spindle nut set

     

  • Mustang II Brake Caliper C-Bracket
    Mustang II Brake Caliper C-Bracket
    x
                Individual brake caliper c-brackets available. Choose right or left.
            
  • Mustang II IFS, Tubular Control Arms, Coilover Springs, Dropped Spindles
    Mustang II IFS, Tubular Control Arms, Coilover Springs, Dropped Spindles
    x
                Hub-to-hub kit includes tubular upper and offset strutless lower control arms, new standard spindles, rubber brake lines, 2" dropped spindles, Carrera coilovers, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Carrera Coilovers
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2&qu

  • Speedway Mustang II Crossmember-1937-39 Chevy Pickup Frame, Kit-Deluxe
    Speedway Mustang II Crossmember-1937-39 Chevy Pickup Frame, Kit-Deluxe
    x
                

    These Speedway Mustang IFS kits for 1937-39 Chevy Pickups are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1937-1939 Chevy Pickup frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers below and add to an IFS kit to get a "

  • Mustang II IFS, Narrow Control Arms, Coilover Springs, Dropped Spindles
    Mustang II IFS, Narrow Control Arms, Coilover Springs, Dropped Spindles
    x
                Hub-to-hub kit includes 5/8" narrower upper and offset strutless lower control arms, 2" dropped spindles, rubber brake lines, Carrera  coilovers, new manual or rebuilt power rack & pinion with  bushings and  new tie rods. The 11" brake kit features GM Metric  calipers, with your  choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Carrera Coilovers
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers

  • Ford Front Axle Steering & Brake Kit, 48 Inch Axle
    Ford Front Axle Steering & Brake Kit, 48 Inch Axle
    x
                

    Speedway's exclusive steering & brake kits save you time and money by combining all necessary parts into one part number. Each kit includes brake kit, spindles, dust caps, spindle nuts, Rubber Brake Lines, AN3 caliper fittings, kingpins, flat steering arms, tie rod assembly and hardware.  

    • For 48" kingpin-to-kingpin axles
    • Traditional steering arm for left front wheel NOT included with Traditional steering kit
    • Available with 5x4.5" or 5x4.75" hubs

    Spindle Identification Guide (GIF)

  • Ford Mustang II-Pinto Caliper
    Ford Mustang II-Pinto Caliper
    x
                Remanufactured Mustang II/Pinto caliper with retaining clip hardware. 7/16"-24 inlet.

     

  • Chevy Front Axle Steering & Brake Kit, 46 Inch Axle
    Chevy Front Axle Steering & Brake Kit, 46 Inch Axle
    x
                Please view the product's page for more information
            
Goto Previous PagePrevious Page
1 2 3 4