Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"brake gm metric style rotors" Page 1 of 2

  • Wilwood 150-8936K BP-10 GM Metric 1978-Up Brake Pads
    Wilwood 150-8936K BP-10 GM Metric 1978-Up Brake Pads
    x
                

    Speedway Motors is your one-stop shop for GM 1978-Up Midsize caliper brake pads.

    • Medium friction, smooth engagement, low abrasion on iron rotors.
    • Flat torque curve.
    • Low to medium wear rate, increases as temperature increases.

    Brake Pad Brochure (PDF)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side. 

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Speedway 1979-Up GM Metric Brake Rotor
    Speedway 1979-Up GM Metric Brake Rotor
    x
                

    This 1979-up GM Metric front disc brake rotor will work with a Set # 6 inner bearing/race which fits most spindles. 5 on 5" with 5/8" coarse studs installed. 10.5" diameter x 1".  Must be used with 912-TS3 outer bearings for 1982-1987 spindle applications.  IMCA Approved.

    This is a 1979-1981 Metric GM rotor with the bolt pattern changed to 5 on 5". It can be used on 1982-1987 GM metric spindles if the you use our bearing/seal kit 91031048, or use at least the 1979-1981 style outer bearing 912TS3.

    This rotor is designed for dirt track applications and should NOT be used for asphalt racing.




     

  • Gasser Straight Axle, Chevy Spindle and Brake Kits, 58-1/2 Hub-to-Hub
    Gasser Straight Axle, Chevy Spindle and Brake Kits, 58-1/2 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3950 Instructions (PDF)

  • Ford 9 Inch Bolt-On Rear Disc Brake Kit
    Ford 9 Inch Bolt-On Rear Disc Brake Kit
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM metric style calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31902 Instructions (PDF)

  • AFCO 1251-1154 D154 1978-Up GM Metric Pads
    AFCO 1251-1154 D154 1978-Up GM Metric Pads
    x
                Please view the product's page for more information
            
  • Wilwood 15E-6103K Poly-E GM Metric 1978-Up Brake Pads
    Wilwood 15E-6103K Poly-E GM Metric 1978-Up Brake Pads
    x
                

    Speedway Motors is your one-stop shop for GM 1978-Up Midsize caliper brake pads.

    Brake Pad Brochure (PDF)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side. 

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Speedway 156 1978-Up GM Metric Brake Pads
    Speedway 156 1978-Up GM Metric Brake Pads
    x
                

    The Speedway 156 brake pad works with aluminum or steel rotors. Best pad for aluminum rotors. Features a low metallic compound for long life and excellent street performance.

    Sold as one pair (PR); outfits one caliper.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • Speedway 1979-Up GM Metric Brake Rotor, 5 on 4-3/4 Inch, 10-1/2 Inch
    Speedway 1979-Up GM Metric Brake Rotor, 5 on 4-3/4 Inch, 10-1/2 Inch
    x
                

    This 1979-up GM Metric front disc brake rotor will work with a Set # 6 inner bearing/race which fits most spindles. 5 on 4-3/4" with 7/16"-20  studs installed. 10.5" diameter x 1".  Must be used with 912-TS3 outer bearings for 1982-1987 spindle applications.  IMCA Approved.

    This is a 1979-1981 Metric GM rotor with the bolt pattern changed to 5 on 4-3/4". It can be used on 1982-1987 GM metric spindles if you use our bearing/seal kit 91031048, or use at least the 1979-1981 style outer bearing 912TS3.

    This rotor is designed for dirt track applications and should NOT be used for asphalt racing.

  • Wilwood 150-9422K BP-20 GM Metric 1978-Up Brake Pads
    Wilwood 150-9422K BP-20 GM Metric 1978-Up Brake Pads
    x
                

    Speedway Motors is your one-stop shop for GM 1978-Up Midsize caliper brake pads.

    Brake Pad Brochure (PDF)

    Tech Tip:  Only use full metallic pads on coated rotors.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side. 

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • Gasser Straight Axle, Chevy Spindle and Brake Kits, 56-1/2 Hub-to-Hub
    Gasser Straight Axle, Chevy Spindle and Brake Kits, 56-1/2 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3948 Instructions (PDF)

  • AFCO 9850-6505 10 Inch Hybrid Brake Rotor for Pinto
    AFCO 9850-6505 10 Inch Hybrid Brake Rotor for Pinto
    x
                

    This brake rotor combines the strength of a '75-'81 Ford-style hub (Granada) with the lighter design of the metric brake rotor for an unbeatable lightweight and durable package.  AFCO engineers designed this rotor with the latest CAD software and testing methods.  Manufactured to withstand rigorous racing environments, the AFCO Hybrid Rotor uses totally new castings designed and built specifically for racing.  It will remove up to 12 lbs. of sprung weight on the front of your car to improve front to rear weight bias and wheel control.

    • Uses GM metric caliper
    • Ford '74-'80 Pinto Spindle
    • Strong and Lightweight
    • Safely remove up to 13 lbs from the front of your car vs stock rotor
    • 14.8# total rotor weight with 5/8" studs
    • 10.13" diameter
    • .813" thickness (pad spacer recommended)

    Instructions (PDF) 

  • Mustang II Complete 11 Inch Front Disc Brake Kit, 5 on 4-3/4 Granada Type Rotor
    Mustang II Complete 11 Inch Front Disc Brake Kit, 5 on 4-3/4 Granada Type Rotor
    x
                Easily upgrade your Mustang II based suspension from the stock 9-1/4"  rotors to 11" rotors with powerful single piston GM Metric style floating  calipers. Kit requires no machining. For use on 1974-1980 Pinto, Bobcat  and Mustang II factory spindles.  
    • GM bolt pattern 5 on 4-3/4" (increases track width 1/2" per side)
    • Includes two 16" front brake hoses and 7/16"-20 banjo bolts with crush washers
    • Granada style rotors

    Front Disc Brake Installation Instructions (PDF)

  • Speedway Soft Street Brake Pads, GM Metric 1978-UP
    Speedway Soft Street Brake Pads, GM Metric 1978-UP
    x
                

    Speedway soft brake pad for GM Metric 1978-Up.

    Sold as one set of 4 (ST); outfits two calipers.

    Tech Tip: You can fine tune your car's brake system by selecting different compounds for the front and rear, or side to side.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

  • AFCO 9850-6501 GM Metric Style Rotors 1979-1987, 5 x 4-3/4 Inch
    AFCO 9850-6501 GM Metric Style Rotors 1979-1987, 5 x 4-3/4 Inch
    x
                

    These AFCO brake rotors are specifically designed for dirt track applications (not for use on asphalt). They meet OEM sanctioning requirements for Modifieds, Street Stocks, and Hobby Stocks.

    • Wheel studs installed
    • Stock-appearing
    • 10.4" diameter x 1" thickness
    • Races installed
    • Pre-drilled with stock 4-3/4" pattern

    This will work from 1979-1987 for Monte Carlo, Grand PRix, Regal, Cutlass and Malibu. This uses bearing kit #10698518500

    Instructions (PDF)

  • AFCO 9850-6500 GM Metric Style Brake Rotors 1979 and Up, 5 x 5 Inch
    AFCO 9850-6500 GM Metric Style Brake Rotors 1979 and Up, 5 x 5 Inch
    x
                

    These AFCO brake rotors are specifically designed for dirt track applications (not for use on asphalt). They meet OEM sanctioning requirements for Modifieds, Street Stocks, and Hobby Stocks.

    • Wheel studs installed
    • Stock-appearing
    • 10.4" diameter x 1" thickness
    • Races installed
    • Pre-drilled with 5 x 5" pattern

    Instructions (PDF)

  • Gasser Straight Axle, Chevy Spindle and Brake Kits, 52-1/2 Hub-to-Hub
    Gasser Straight Axle, Chevy Spindle and Brake Kits, 52-1/2 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3944 Instructions (PDF)

  • Gasser Straight Axle, Chevy Spindle and Brake Kits, 54-1/2 Hub-to-Hub
    Gasser Straight Axle, Chevy Spindle and Brake Kits, 54-1/2 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3946 Instructions (PDF)

  • Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-3/4
    Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-3/4
    x
                

    An economical, lightweight brake kit for 1949-54 Chevy car spindles. Your stock Chevy spindles must be machined, or use Speedway '49-'54 Chevy-style spindles. This kit uses 9-1/4" Mustang II vented rotors with common GM metric calipers.

    • Typically used on Model T and Model A to 1936 Ford front ends 
    • For use on street rod tube front axles when using 1949-54 Chevy style spindles  
    • Will not work with stock 1949-54 steering arms 
    • Not to be installed on stock 1949-54 Chevy vehicle front ends

    910-31956 Instructions (PDF)

  • Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-1/2
    Front Disc Brake Kit, GM Metric/Mustang II to 1949-54 Chevy Spindle, 5 on 4-1/2
    x
                

    An economical, lightweight brake kit for 1949-54 Chevy car spindles. Your stock Chevy spindles must be machined, or use Speedway '49-'54 Chevy-style spindles. This kit uses 9-1/4" Mustang II vented rotors with common GM metric calipers.

    • Typically used on Model T and Model A to 1936 Ford front ends 
    • For use on street rod tube front axles when using 1949-54 Chevy style spindles  
    • Will not work with stock 1949-54 steering arms 
    • Not to be installed on stock 1949-54 Chevy vehicle front ends

    910-31955 Instructions (PDF)

  • Weld-On Rear Disc Brake Kit, 1978-88 GM Caliper, 3 Inch Backspace
    Weld-On Rear Disc Brake Kit, 1978-88 GM Caliper, 3 Inch Backspace
    x
                

    Replace those old drum brakes with modern rear disc brakes. Mounts .81" x 11-3/4" Pro-lite vented iron rotors and calipers to 3" tube rear end. Complete with rotors, hats, metric calipers (7/16"-20 inlets), brackets, brake pads, caliper brackets and slider bolts. 

    Steel hat fits 5 lug hubs with 4-1/2", 4-3/4", or 5" bolt circle.

    910-31931 Instructions (PDF)

  • Weld-On Rear Disc Brake Kit, 1978-88 GM Caliper, 1.59 Inch Backspace
    Weld-On Rear Disc Brake Kit, 1978-88 GM Caliper, 1.59 Inch Backspace
    x
                

    Replace those old drum brakes with modern rear disc brakes. Mounts .81" x 11-3/4" Pro-lite vented iron rotors and calipers to 3" tube rear end. Complete with rotors, hats, metric calipers (7/16"-20 inlets), brackets, brake pads, caliper brackets and slider bolts.

    Hat fits 5 lug hubs with 4-1/2", 4-3/4", or 5" bolt circle.

    910-31932 Instructions (PDF)

  • Gasser Straight Axle, Ford Spindle and Brake Kits, 56-1/4 Hub-to-Hub
    Gasser Straight Axle, Ford Spindle and Brake Kits, 56-1/4 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3548 Instructions (PDF)

  • Gasser Straight Axle, Ford Spindle and Brake Kits, 58-1/4 Hub-to-Hub
    Gasser Straight Axle, Ford Spindle and Brake Kits, 58-1/4 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3550 Instructions (PDF)

  • GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit
    GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit
    x
                

    If you don't want to spend and arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes two bolt-on caliper brackets, two 11-5/8" vented rotors, two GM metric style calipers, brake pads and hardware.

    • 5 on 4-3/4" bolt circle
    • Fits over an axle with a maximum flange diameter of 6" O.D.
    • 2.872" rotor center hole
    • Requires a minimum 14-5/8" I.D. for caliper clearance 

    910-31923 Instructions (PDF)

  • Gasser Straight Axle, Ford Spindle and Brake Kits, 54-1/4 Hub-to-Hub
    Gasser Straight Axle, Ford Spindle and Brake Kits, 54-1/4 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3546 Instructions (PDF)

  • Gasser Straight Axle, Ford Spindle and Brake Kits, 52-1/4 Hub-to-Hub
    Gasser Straight Axle, Ford Spindle and Brake Kits, 52-1/4 Hub-to-Hub
    x
                

    These kits include our gasser straight front axle, semi-elliptical springs, spindles, king pins, steering arms, tierod kit, brake kit, and hardware. Choose either 5 on 4-1/2" or 5 on 4-3/4" bolt pattern with standard brake kit or Wilwood brake kit. Standard brake kits use new rotors and GM metric style calipers. Brake lines not included. Shocks not included, but shock mounts are included. Assembly required.

    Gasser Info (PDF)

    Note: Wilwood brakes increase hub-to-hub width by 1/2".

    910-3544 Instructions (PDF)

  • Basic Brake Kit 1978-88 GM Caliper to Early Ford Spindles
    Basic Brake Kit 1978-88 GM Caliper to Early Ford Spindles
    x
                Easily installs 11" rotors and the 1978-up GM Metric calipers to your 1937-48 Ford passenger car spindles. No machine work needed. Please see below for suggested 1973-77 GM type 11" brake rotor part #'s required.

    Kit Includes:
    • GM to Ford brake brackets
    • 1978-Up hardware
    • Bearing and seal adapters
    • Seals
    • Inner bearing cups
    • Inner bearing cones
    • Spacers
    • Instructions
    • Does not include dust caps, washers or spindle nuts

    This kit works well with bolt-on steering arms. The 11" rotor brake kits are great for Street Rods based on 1932-48 Fords. However, for or a T bucket or early roadster, you might consider the Wilwood kits shown below.

    702-4475 Instructions (PDF)

  • Basic Disc Brake Kit, 1955-64 Chevy Fullsize Car, Stock Spindle
    Basic Disc Brake Kit, 1955-64 Chevy Fullsize Car, Stock Spindle
    x
                

    This kit allows you to put front disc brakes on your 1955-64 fullsize Chevy passenger car (Bel-Air, Biscayne, Impala, 150 Series, 210 Series) OEM spindles (will NOT work with dropped spindles). It will work with 14" wheels intended for disc brakes, as well as most 15" (or larger) wheels. Works with 5 on 4-3/4 inch bolt patterns.

    Use with our 11" rotor 910-65390 and metric caliper 910-31045 (see Notes). This kit will increase track width 3/8" per side or or 3/4" total when installed.

    Kit Includes:

    • Brake brackets
    • Hardware
    916-31931 Instructions (PDF)
  • Hawk HB119M.594 Performance Black 1978-Up GM Metric Brake Pads
    Hawk HB119M.594 Performance Black 1978-Up GM Metric Brake Pads
    x
                

    Get superior stopping power with Hawk Performance! Hawk Performance brake pads have been successful in virtually all forms of motorsports for over 16 years. This success helps Hawk Performance enjoy the benefits of the “Win on Sunday, Sell on Monday,” philosophy. Hawk is one of few brake pad manufacturers that can deliver on the promise, “Race Proven – Street Legal.”

    Hawk Black Pads:

    Medium torque and temperature compound designed to be a good, all-purpose low- cost racing brake pad. Can be used as a Dirt Circle Track and Stock Car application.

    Tech Tip:  Only use full metallic pads on coated rotors.

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly Bed-In your brake pads by reading our tech article.  Bedding-In Brake Pad Procedure.

     

  • GM 10 & 12 Bolt Bolt-On Rear Disc Brake Kit
    GM 10 & 12 Bolt Bolt-On Rear Disc Brake Kit
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This complete kit includes two bolt-on caliper brackets, two 11-1/4" vented rotors, two GM metric style calipers, brake pads and hardware.

    • Rotors have both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • Fits axle with a maximum flange diameter of 6-1/4" O.D.
    • 2.780" rotor center hole
    • Does not fit all 10 & 12 bolt axles. Check Application tab for details. 

    Axle Flange Identification Chart (GIF)

    910-31919 Instructions (PDF)

  • Disc Brake Kit 1978-88 GM Caliper to Early Ford Spindle, 5 on 4-3/4 Inch
    Disc Brake Kit 1978-88 GM Caliper to Early Ford Spindle, 5 on 4-3/4 Inch
    x
                

    Easily install 11" rotors and 1978-88 GM Metric calipers to your 1937-48 Ford passenger car style spindles with no machine work needed. This disc brake kit is great for street rods based on 1932-1948 Fords. For lightweight cars like T-buckets or early roadsters, we recommend the Wilwood kits. This front disc brake conversion kit works well with bolt-on steering arms. The 11" diameter rotors have the GM wheel bolt pattern of 5 x 4-3/4". Calipers have 7/16"-20 inlets.

    910-31946 Instructions (PDF)

  • Speedway 1978-88 GM Metric Brake Pad Spacer
    Speedway 1978-88 GM Metric Brake Pad Spacer
    x
                Use Speedway brake pad spacers with .810" rotors and stock-style 1978-1988 GM calipers. Spaces brake pad out .242" from caliper piston.
            
  • Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
    Garage Sale
    Garage Sale - 11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper
    x
                Please view the product's page for more information
            
  • Garage Sale - Speedway 1979-Up GM Metric Brake Rotor, 5 on 4-3/4 Inch, 10-1/2 Inch
    Garage Sale
    Garage Sale - Speedway 1979-Up GM Metric Brake Rotor, 5 on 4-3/4 Inch, 10-1/2 Inch
    x
                Please view the product's page for more information
            
  • Garage Sale - Speedway 156 1978-Up GM Metric Brake Pads
    Garage Sale
    Garage Sale - Speedway 156 1978-Up GM Metric Brake Pads
    x
                Please view the product's page for more information
            
  • Hawk HB119H.594 Performance 1978-Up GM Metric HPS Brake Pads
    Hawk HB119H.594 Performance 1978-Up GM Metric HPS Brake Pads
    x
                

    Get superior stopping power with Hawk Performance! Hawk Performance brake pads have been successful in virtually all forms of motorsports for over 16 years. This success helps Hawk Performance enjoy the benefits of the “Win on Sunday, Sell on Monday,” philosophy. Hawk is one of few brake pad manufacturers that can deliver on the promise, “Race Proven – Street Legal.”

    Increasing the performance of your vehicles braking system is easy when you choose Hawk Performance’s HPS braking compound. This unique Ferro-Carbon formula was developed for street performance using the safety and quality of Motorsports severe-duty friction technology.

    • Higher coefficient of friction over stock brake pads
    • Provides 20-40% more stopping power and higher resistance to brake fade than most standard replacement pads
    • Less fade means a highly durable brake pad with less brake dust

    Tech Tip:  Only use full metallic pads on coated rotors.

    Sold as a set of 4, 1 set will be needed to outfit 2 calipers.

    Brake Pad Brand Guide (Link) 

    Learn how to properly B

  • Garage Sale - AFCO Right Front 10 Inch Hybrid Brake Rotor Caliper Bracket
    Garage Sale
    Garage Sale - AFCO Right Front 10 Inch Hybrid Brake Rotor Caliper Bracket
    x
                

    Use with 1974-1980 Pinto/Mustang II spindle, 10" hybrid rotor and GM 1978-up "Metric" caliper.

    Sides are reversed on '73 & older spindles.

     

     This brake bracket is garage sale priced because it has been bolted on.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

  • Garage Sale - AFCO Front Left 10 Inch Hybrid Brake Rotor Caliper Bracket
    Garage Sale
    Garage Sale - AFCO Front Left 10 Inch Hybrid Brake Rotor Caliper Bracket
    x
                

    Use with 1974-1980 Pinto/Mustang II spindle, 10" hybrid rotor and GM 1978-up "Metric" caliper.

    Sides are reversed on '73 & older spindles.

     

    This bracket is garage sale priced because it has been bolted on and returned. 

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

  • Garage Sale - AFCO 7250-0120 GM 7.5 Inch Axle Brake Kit
    Garage Sale
    Garage Sale - AFCO 7250-0120 GM 7.5 Inch Axle Brake Kit
    x
                Please view the product's page for more information
            
  • Economy Bolt-On Front/Rear Brake Kit for Chevy Spindle
    Economy Bolt-On Front/Rear Brake Kit for Chevy Spindle
    x
                

    Complete the front and rear suspension assembly on your T roadster chassis with a bolt-on brake kit specifically designed for our '49-'54 Chevy style spindles and 9" Ford rear end. Each kit includes all necessary components: new rotors (available with 5-on-4.5" or 5-on-4.75" bolt pattern), remanufactured GM Metric calipers, caliper brackets, brake pads, bearings, seals and hardware. Rear kit bots on new-style Big Ford ends.

    Chevy Spindle Brake Kit Instructions (PDF) 

Goto Previous PagePrevious Page
1 2