Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"adjustable drag shocks" Page 1 of 7

  • AFCO 6875F Reactor 1993-02 Camaro Front Drag Shocks
    AFCO 6875F Reactor 1993-02 Camaro Front Drag Shocks
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    Fits 1993-2002 Chevy Camaro and Pontiac Firebird.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock with included kit
    • 100% co-Tested and Serial Numbered

    Note: Coil-over kit is included with each shock. Coil spring NOT included.

  • AFCO 6855M Reactor 1962-67 Chevy II Front Drag Shock, 5 Inch Stroke
    AFCO 6855M Reactor 1962-67 Chevy II Front Drag Shock, 5 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered
    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    Fits 1962-1967 Chevy II Nova. (May need to "slot" tie bar mount.)

  • AFCO 6845F Reactor Front Drag Shocks - Chevrolet/GM/Dodge
    AFCO 6845F Reactor Front Drag Shocks - Chevrolet/GM/Dodge
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered

    Fits most '55-'96 GM chassis

    Fits 1979-1992 Dodge Ram half-ton 2WD pickup trucks.

    See Applications tab for fittment.

  • AFCO 6865M Reactor Mopar Front Drag Shock, 6 Inch Stroke
    AFCO 6865M Reactor Mopar Front Drag Shock, 6 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube FRONT shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Plus, with AFCO's exclusive "BNC" valving, these shocks eliminate bounce caused by the impact after a wheel stand.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • BNC Valving eliminates front end bounce
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered

    106-6865M

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    See Applications tab for Dodge-Plymouth chassis fittment.

  • AFCO 6895M Reactor Rear Drag Shocks - Mopar
    AFCO 6895M Reactor Rear Drag Shocks - Mopar
    x
                

    AFCO Single Adjustable Monotube REAR shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. Coil-over kit is included.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • Includes coil-over kit
    • 100% co-Tested and Serial Numbered

    See Applications tab for Chrysler/Dodge/Plymouth chassis fittment.

  • AFCO 6875R 6875R Reactor Rear Drag Shock, Ford/Mercury, 7 Inch Stroke
    AFCO 6875R 6875R Reactor Rear Drag Shock, Ford/Mercury, 7 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube REAR shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered
    1. The rebound adjustment is the most critical in tuning a drag racing set-up. This adjustment allows the tuner to dial in the "un-loading action" of the chassis and keep the tires planted during the critical first 60' down the track.
    2. Can be used as a coil-over shock with 106-20135D coil-over hardware kit (purchase separate).
    3. Check extended and compressed dimensions.

    See Applications tab for Ford-Mercury chassis fittment.

  • AFCO 6875R-1 6875R-1 Reactor Rear Drag Shock, Chevy/GM, 7 Inch Stroke
    AFCO 6875R-1 6875R-1 Reactor Rear Drag Shock, Chevy/GM, 7 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube REAR shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  Tie Bar with 2.375" bolt centers
    • Shaft Mount:  1/2" I.D. bearing (1.06")
    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered
    1. The rebound adjustment is the most critical in tuning a drag racing set-up. This adjustment allows the tuner to dial in the "un-loading action" of the chassis and keep the tires planted during the critical first 60' down the track.
    2. Can be used as a coil-over shock with 106-20135D coil-over hardware kit (purchase separate).

    Fits most '55-'96 GM chassis - see Applications tab for fittment.

  • AFCO 6875R-2 6875R-2 Reactor Rear Drag Shock, Chevy/GM, 7 Inch Stroke
    AFCO 6875R-2 6875R-2 Reactor Rear Drag Shock, Chevy/GM, 7 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube REAR shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  Tie Bar with 2.375" bolt centers
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • Can be upgraded to a coil-over shock
    • 100% co-Tested and Serial Numbered
    1. The rebound adjustment is the most critical in tuning a drag racing set-up. This adjustment allows the tuner to dial in the "un-loading action" of the chassis and keep the tires planted during the critical first 60' down the track.
    2. Can be used as a coil-over shock with 106-20135D coil-over hardware kit (purchase separate).

    Fits most '55-'96 GM chassis - see Applications tab for fittment.

  • AFCO 3860M-2 Chrysler-Dodge LX Front Double Adjustable Drag Pak Shock
    AFCO 3860M-2 Chrysler-Dodge LX Front Double Adjustable Drag Pak Shock
    x
                

    AFCO & MOPAR co-developed this bolt on, Stock and Super Stock legal suspension package for the LX platform. The double adjustable front and rear shocks allow changes to be made with a simple “click” of a knob. This complete suspension package has been designed and rigorously tested by AFCO and MOPAR Motorsports.

    • Independent compression and rebound adjustability
    • Spring rates/sizes specifically tuned for the strip
    • Featured on the MOPAR “DRAG PAK” Challengers
    • Direct bolt-in fit (all hardware included)
    • Specifically valved for the strip to maximize the full power potential of your HEMI

    Installation Guide (PDF)

    Front Spring:  250# rate, 14" height
    Rear Spring:  125# rate, 12" height

    Fits Chrysler/Dodge LX platform drag vehicles:

    • Chrysler 300C
    • Dodge Challenger, Charger, and Magnum

     

  • AFCO 3870M-2 Chrysler-Dodge LX Rear Double Adjustable Drag Pak Shock
    AFCO 3870M-2 Chrysler-Dodge LX Rear Double Adjustable Drag Pak Shock
    x
                

    AFCO & MOPAR co-developed this bolt on, Stock and Super Stock legal suspension package for the LX platform. The double adjustable front and rear shocks allow changes to be made with a simple “click” of a knob. This complete suspension package has been designed and rigorously tested by AFCO and MOPAR Motorsports.

    • Independent compression and rebound adjustability
    • Featured on the MOPAR “DRAG PAK” Challengers
    • Direct bolt-in fit (all hardware included)
    • Specifically valved for the strip to maximize the full power potential of your HEMI

    Installation Guide (PDF)

    Fits Chrysler/Dodge LX platform drag vehicles:

    • Chrysler 300C
    • Dodge Challenger, Charger, and Magnum

     

  • AFCO 3855 Eliminator Coil-Over Shock, Single Adjustable, 5 Inch Stroke
    AFCO 3855 Eliminator Coil-Over Shock, Single Adjustable, 5 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Rebound Adjustable with the "click" of a knob
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Bearing mount ends reduce suspension binding
    • Includes all hardware to mount a 2-5/8" spring
    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3835 Eliminator Coil-Over Shock, Single Adjustable, 3 Inch Stroke
    AFCO 3835 Eliminator Coil-Over Shock, Single Adjustable, 3 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Rebound Adjustable with the "click" of a knob
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Bearing mount ends reduce suspension binding
    • Includes all hardware to mount a 2-5/8" spring
    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3895 Eliminator Coil-Over Shock, Single Adjustable, 9 Inch Stroke
    AFCO 3895 Eliminator Coil-Over Shock, Single Adjustable, 9 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Rebound Adjustable with the "click" of a knob
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Bearing mount ends reduce suspension binding
    • Includes all hardware to mount a 2-5/8" spring
    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3875 Eliminator Coil-Over Shock, Single Adjustable, 7 Inch Stroke
    AFCO 3875 Eliminator Coil-Over Shock, Single Adjustable, 7 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Rebound Adjustable with the "click" of a knob
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Bearing mount ends reduce suspension binding
    • Includes all hardware to mount a 2-5/8" spring
    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3845 Eliminator Coil-Over Shock, Single Adjustable, 4 Inch Stroke
    AFCO 3845 Eliminator Coil-Over Shock, Single Adjustable, 4 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Rebound Adjustable with the "click" of a knob
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Bearing mount ends reduce suspension binding
    • Includes all hardware to mount a 2-5/8" spring
    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3865M Mopar Eliminator Single Adjustable Front Shock, 6 In Stroke
    AFCO 3865M Mopar Eliminator Single Adjustable Front Shock, 6 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • AFCO 3855M Mopar Eliminator Single Adjustable Front Shock, 5 In Stroke
    AFCO 3855M Mopar Eliminator Single Adjustable Front Shock, 5 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • AFCO 3870R-1 Eliminator Double Adjustable Rear Shock, 7 Inch, Chevy/GM
    AFCO 3870R-1 Eliminator Double Adjustable Rear Shock, 7 Inch, Chevy/GM
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    • 106-3875R1
      • Body Mount:  Tie Bar with 2.375" bolt centers
      • Shaft Mount:  1/2" I.D. bearing (1.06")

    Fits most '55-'96 GM chassis - see Applications tab for fittment.

  • AFCO 3875F Eliminator 1993-02 Camaro Front Shocks - Single Adj
    AFCO 3875F Eliminator 1993-02 Camaro Front Shocks - Single Adj
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready

    Fits 1993-2002 GM F-Body (Chevy Camaro, Pontiac Firebird). Coil-over kit hardware is included.

  • AFCO 3860M Mopar Eliminator Double Adjustable Front Shock, 6 In Stroke
    AFCO 3860M Mopar Eliminator Double Adjustable Front Shock, 6 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.  By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • AFCO 3850M Mopar Eliminator Double Adjustable Front Shock, 5 In Stroke
    AFCO 3850M Mopar Eliminator Double Adjustable Front Shock, 5 In Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.  By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Body Mount:  1/2" I.D. Bearing (1.06" wide)
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for Dodge-Plymouth chassis fittment.

  • AFCO 3870F Eliminator 1993-02 Camaro Front Shocks - Double Adj
    AFCO 3870F Eliminator 1993-02 Camaro Front Shocks - Double Adj
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready

    Fits 1993-2002 GM F-Body (Chevy Camaro, Pontiac Firebird). Coil-over kit hardware is included.

  • AFCO 3875R Eliminator Rear Shocks-Single Adj. 7 In Stroke-Ford/Mercury
    AFCO 3875R Eliminator Rear Shocks-Single Adj. 7 In Stroke-Ford/Mercury
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Body Mount:  Tie Bar Mount w/ 2.375" bolt centers
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    See Applications tab for Ford-Mercury chassis fittment.

     

  • AFCO 3870R Eliminator Rear Double Adj. Shock, 7 In Stroke-Ford/Mercury
    AFCO 3870R Eliminator Rear Double Adj. Shock, 7 In Stroke-Ford/Mercury
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Body Mount:  Tie Bar Mount w/ 2.375" bolt centers
    • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    See Applications tab for Ford-Mercury chassis fittment.

  • AFCO 3850F Eliminator 1962-67 Chevy II Front Shocks, Double Adj
    AFCO 3850F Eliminator 1962-67 Chevy II Front Shocks, Double Adj
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability. 

    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    Fits 1962-1967 Chevy II/Nova (may need to "slot" tie bar mount). 

  • AFCO 3895M Eliminator Rear Shocks, Single Adj - Mopar
    AFCO 3895M Eliminator Rear Shocks, Single Adj - Mopar
    x
                AFCO Eliminator Twin Tube Adjustable REAR shocks are built  specifically for drag racing. Using advanced onboard diagnostics, AFCO developed  the Eliminator Series to precisely control your race car at every point on the  track. With the easy-to-use, repeatable "click" settings, this shock will give  you unsurpassed traction. 

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready

    See Applications tab for Chrysler/Dodge/Plymouth chassis fittment.

  • AFCO 3875R-1 Eliminator Rear Shock-7 Inch, Bearing Shaft, Chevrolet/GM
    AFCO 3875R-1 Eliminator Rear Shock-7 Inch, Bearing Shaft, Chevrolet/GM
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • 106-3875R1
      • Body Mount:  Tie Bar with 2.375" bolt centers
      • Shaft Mount:  1/2" I.D. bearing (1.06")

    Fits most '55-'96 GM chassis - see Applications tab for fittment.

  • AFCO 3890M Eliminator Rear Shocks, Double Adj - Mopar
    AFCO 3890M Eliminator Rear Shocks, Double Adj - Mopar
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready

    See Applications tab for Chrysler/Dodge/Plymouth chassis fittment.

  • AFCO 3875R-2 Eliminator Adj Rear Shock-7 Inch-Shaft Stud, Chevrolet/GM
    AFCO 3875R-2 Eliminator Adj Rear Shock-7 Inch-Shaft Stud, Chevrolet/GM
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • 106-3875R2
      • Body Mount:  Tie Bar with 2.375" bolt centers
      • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)

    Fits most '55-'96 GM chassis - see Applications tab for fittment.

  • AFCO 3845F Eliminator Front Shocks, Single Adj - Chevy/GM/Dodge Truck
    AFCO 3845F Eliminator Front Shocks, Single Adj - Chevy/GM/Dodge Truck
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    Single (Rebound) Adjustable shocks are an economical alternative that gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock.

    • Lightweight aluminum construction easily dissipates heat 
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    Fits most '55-'96 GM chassis

    Fits most '79-92 Dodge Trucks 

    See Application tab for fittment.

     

  • AFCO 3840F Eliminator Front Shocks, Double Adj - Chevrolet/GM, Dodge
    AFCO 3840F Eliminator Front Shocks, Double Adj - Chevrolet/GM, Dodge
    x
                

    AFCO Eliminator Twin Tube Adjustable FRONT shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D
    Fits 1979-1992 Dodge Ram half-ton pickup trucks

    Fits most '55-'96 GM chassis

    See Application tab for fittment.

  • AFCO 3870R-2 Eliminator Adj. Rear Shock 7 In, Chevy/GM, 1970-81 Camaro
    AFCO 3870R-2 Eliminator Adj. Rear Shock 7 In, Chevy/GM, 1970-81 Camaro
    x
                

    AFCO Eliminator Twin Tube Adjustable REAR shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    • 106-3875R2
      • Body Mount:  Tie Bar with 2.375" bolt centers
      • Shaft Mount:  9/16" Stud (3-1/8" length, 1-1/8" threads, 1-3/4" washers)
    • Lightweight aluminum construction also helps dissipate heat
    • Rebound settings are adjusted via a shaft-mounted knob with 32 clicks
    • Compression settings are adjusted via a body-mounted know with 32 clicks
    • Smooth, Ultra Low Friction rod guide
    • Low resistance allows internals to function to their fullest potential
    • Almost no "stiction" to interfere with putting the power down
    • Coil-over Ready w/ purchase of kit 106-20135D

    See Applications tab for fittment.

  • AFCO 6875 Reactor Gas Bracket Attack Coil-Over Shock, 7 Inch Stroke
    AFCO 6875 Reactor Gas Bracket Attack Coil-Over Shock, 7 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube Bracket Attack coil-over shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. 

    The rebound adjustment is the most critical in tuning a drag racing set-up. This adjustment allows the tuner to dial in the "un-loading action" of the chassis and keep the tires planted during the critical first 60' down the track.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • 100% co-Tested and Serial Numbered

    Includes coil-over kit. Coil spring NOT included.

  • AFCO 6865 Reactor Gas Bracket Attack Coil-Over Shock, 6 Inch Stroke
    AFCO 6865 Reactor Gas Bracket Attack Coil-Over Shock, 6 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube Bracket Attack coil-over shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. 

    The rebound adjustment is the most critical in tuning a drag racing set-up. This adjustment allows the tuner to dial in the "un-loading action" of the chassis and keep the tires planted during the critical first 60' down the track.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • 100% co-Tested and Serial Numbered

    Includes coil-over kit. Coil spring NOT included.

  • AFCO 6845 Reactor Gas Bracket Attack Coil-Over Shock, 4 Inch Stroke
    AFCO 6845 Reactor Gas Bracket Attack Coil-Over Shock, 4 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube Bracket Attack coil-over shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. 

    The rebound adjustment is the most critical in tuning a drag racing set-up. This adjustment allows the tuner to dial in the "un-loading action" of the chassis and keep the tires planted during the critical first 60' down the track.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • 100% co-Tested and Serial Numbered

    Includes coil-over kit. Coil spring NOT included.

  • AFCO 6855 Reactor Gas Bracket Attack Coil-Over Shock, 5 Inch Stroke
    AFCO 6855 Reactor Gas Bracket Attack Coil-Over Shock, 5 Inch Stroke
    x
                

    AFCO Single Adjustable Monotube Bracket Attack coil-over shocks are an economical alternative to the fully double adjustable design. The single adjustable gives you the ability to adjust rebound dampening control without affecting the compression dampening characteristics of the shock. 

    The rebound adjustment is the most critical in tuning a drag racing set-up. This adjustment allows the tuner to dial in the "un-loading action" of the chassis and keep the tires planted during the critical first 60' down the track.

    • Quicker R.T.'s
    • Gas Mono-tube design for superior tuning and performance
    • Rebound adjustable only - will not bleed over to compression
    • 100% co-Tested and Serial Numbered

    Includes coil-over kit. Coil spring NOT included.

  • AFCO 3830 Eliminator Coil-Over Shock, Double Adjustable, 3 Inch Stroke
    AFCO 3830 Eliminator Coil-Over Shock, Double Adjustable, 3 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    Double adjustable shocks are the ultimate tool in the chassis tuner's arsenal. The double adjustments of both compression and rebound dampening are completely independent - changing the setting of one has no effect on the setting of the other.

    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3870 Eliminator Coil-Over Shock, Double Adjustable, 7 Inch Stroke
    AFCO 3870 Eliminator Coil-Over Shock, Double Adjustable, 7 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    Double adjustable shocks are the ultimate tool in the chassis tuner's arsenal. The double adjustments of both compression and rebound dampening are completely independent - changing the setting of one has no effect on the setting of the other.

    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3890 Eliminator Coil-Over Shock, Double Adjustable, 9 Inch Stroke
    AFCO 3890 Eliminator Coil-Over Shock, Double Adjustable, 9 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    Double adjustable shocks are the ultimate tool in the chassis tuner's arsenal. The double adjustments of both compression and rebound dampening are completely independent - changing the setting of one has no effect on the setting of the other.

    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

  • AFCO 3840 Eliminator Coil-Over Shock, Double Adjustable, 4 Inch Stroke
    AFCO 3840 Eliminator Coil-Over Shock, Double Adjustable, 4 Inch Stroke
    x
                

    AFCO Eliminator Twin Tube Adjustable shocks are built specifically for drag racing. Using advanced onboard diagnostics, AFCO developed the Eliminator Series to precisely control your race car at every point on the track. With the easy-to-use, repeatable "click" settings, this shock will give you unsurpassed traction.

    By allowing full control over both compression and rebound forces, Double Adjustable shocks give the tuner the ability to fine tune every aspect of the chassis movement to provide the ultimate in acceleration control and overall driveability.

    Double adjustable shocks are the ultimate tool in the chassis tuner's arsenal. The double adjustments of both compression and rebound dampening are completely independent - changing the setting of one has no effect on the setting of the other.

    • Body Mount:  1/2" I.D. Bearing (1.060" wide)
    • Shaft Mount:  1/2" I.D. Bearing (1.060" wide)

    How to Choose Shock Length (GIF)

    Note: Coil spring NOT included.

Goto Previous PagePrevious Page
1 2 3 4 5 6 7