Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"90 degree hose fitting" Page 1 of 6

  • Air Conditioning Kit w/ Condenser
    Air Conditioning Kit w/ Condenser
    x
                

    The days of riding around trying to look cool while sweating your butt off are gone! So is going to the junkyard and trying to find used parts to cobble up an a/c system. These kits have three dash vents and two defrost ducts and are engineered for 1930's coupes, pick-ups and smaller cars.

    These are designed with both the a/c evaporator and heater core in one unit which helps keep size and installation time down. They fit under the dash just like a new car and allow disassembly without removing the unit from the car.

    They include dash louvers, defrost louvers, switch panel, a/c hose kit, dryer with switch, Sanden 508 compressor  with V-belt pulley, and evaporator/heater assembly. They are available with or without condenser and standard finish or deluxe polished aluminum compressor.

    Hoses will need to be crimped by your local shop. R134a Freon required, but not supplied. Compressor brackets and heater hoses sold separately.

    Instructions (PDF) 

  • A/C Hose Kit
    $89.99
    Product Rating: 5.00 Stars
    A/C Hose Kit
    x
                

    These air conditioning hose kits include enough hose and fittings to allow a normal installation in applications without bulkhead fittings. 

    • (2) Band Clamps
    • (4) AN6 Straight
    • (1) AN8 Straight
    • (1) AN10 Straight
    • (2) AN6 90 Degree
    • (1) AN8 90 Degree
    • (1) AN10 90 Degree
    • (1) AN8 90 Degree with Service Port
    • (1) AN10 90 Degree with Service Port
    • (4) #6 O-Rings
    • (2) #8 O-Rings
    • (2) #10 O-Rings
    • (2) Grommets
    • 6 ft #6 Hose
    • 5 ft #8 Hose
    • 4 ft #10 Hose

     

    Fittings will need to be crimped at your local shop.

  • 90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    90 Degree Crimp-On O-Ring Heater Hose Fitting, -10 AN
    x
                

    These premium -10 size (7/8" x 14 TPI) crimp-on hose fittings feature O-ring seals and a 90 degree bend. Ideal for use with heater bulkhead plates.

    Note: Will need to be crimped by your local shop. 

  • Black 90 Degree Socketless Push-On Hose End Fitting, -6 AN
    Black 90 Degree Socketless Push-On Hose End Fitting, -6 AN
    x
                

    Black socketless push-on hose end fittings will give your engine compartment the look you are after. 90 degree fittings in multiple sizes.  For use with 37 degree flared ends.

    • -6 AN female to push-on hose barb adapter
    • 90° fuel line hose connector
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Black anodized finish

    Socketless Push-On Hose Ends Application Chart (GIF)

     

  • Aeroquip FBM4035 Hose End Coupler Fitting, 90 Degree, Blue/Red, -12 AN
    Aeroquip FBM4035 Hose End Coupler Fitting, 90 Degree, Blue/Red, -12 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a blue/red anodized finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617312).

    • -12 AN 
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Available in Blue/Red corrosion resistant finish

    90° Full Flow Ends come in sizes of AN4, AN6, AN8, AN10, AN12 and AN16.

    Fitting Thread Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Black Anodized, -6 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Black Anodized, -6 AN
    x
                Please view the product's page for more information
            
  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Red/Blue, -6 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Red/Blue, -6 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then red and blue anodized to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -6 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • Aeroquip FCE4032 Nickel 90 Degree Hose End Coupler Fitting, -6 AN
    Aeroquip FCE4032 Nickel 90 Degree Hose End Coupler Fitting, -6 AN
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain.

    Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters from Aeroquip. Lighter and more affordable than stainless steel, these electoless nickel plated pieces combine great corrosion resistance with a neutral color and classy appearance.

    These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a nickel-plated finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617306).

    • -6 AN Aluminum
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Nickel corrosion resistant finish

    Fitting Thread Application Chart (GIF)

  • Aeroquip FBM4233 Starlite Crimp Fitting, 90 Degree, -8 AN
    Aeroquip FBM4233 Starlite Crimp Fitting, 90 Degree, -8 AN
    x
                

    Aeroquip's incredible Starlite racing hose and fittings are up to 45% lighter than stainless steel braided hose and reusable fittings. Can be used with fuel, lube and coolants. Working temperature is -45° to +300°F and have a 200 psi working pressure.

    Starlite hose can be used with either crimp style or reusable hose fittings. Crimp style fitting must be used only with Starlite hose and installed by qualified personnel using an Aeroquip ProCrimp 1380 crimping machine.

    There are only two ways to order these fittings and hose:

    1. Bring or mail us your old hose to match.
    2. We will send you the fittings and hose you think will work. You cut the hose to length and send it back to us for crimping.

    Fitting Thread Application Chart (GIF)

  • Aeroquip FBM4234 Starlite Crimp Fitting, 90 Degree, -10 AN
    Aeroquip FBM4234 Starlite Crimp Fitting, 90 Degree, -10 AN
    x
                

    Aeroquip's incredible Starlite racing hose and fittings are up to 45% lighter than stainless steel braided hose and reusable fittings. Can be used with fuel, lube and coolants. Working temperature is -45° to +300°F and have a 200 psi working pressure.

    Starlite hose can be used with either crimp style or reusable hose fittings. Crimp style fitting must be used only with Starlite hose and installed by qualified personnel using an Aeroquip ProCrimp 1380 crimping machine.

    There are only two ways to order these fittings and hose:

    1. Bring or mail us your old hose to match.
    2. We will send you the fittings and hose you think will work. You cut the hose to length and send it back to us for crimping.

    Fitting Thread Application Chart (GIF)

  • Aeroquip FBM4236 Starlite Crimp Fitting, 90 Degree, -16 AN
    Aeroquip FBM4236 Starlite Crimp Fitting, 90 Degree, -16 AN
    x
                

    Aeroquip's incredible Starlite racing hose and fittings are up to 45% lighter than stainless steel braided hose and reusable fittings. Can be used with fuel, lube and coolants. Working temperature is -45° to +300°F and have a 200 psi working pressure.

    Starlite hose can be used with either crimp style or reusable hose fittings. Crimp style fitting must be used only with Starlite hose and installed by qualified personnel using an Aeroquip ProCrimp 1380 crimping machine.

    There are only two ways to order these fittings and hose:

    1. Bring or mail us your old hose to match.
    2. We will send you the fittings and hose you think will work. You cut the hose to length and send it back to us for crimping.

    Fitting Thread Application Chart (GIF)

  • Aeroquip FBM4235 Starlite Crimp Fitting, 90 Degree, -12 AN
    Aeroquip FBM4235 Starlite Crimp Fitting, 90 Degree, -12 AN
    x
                

    Aeroquip's incredible Starlite racing hose and fittings are up to 45% lighter than stainless steel braided hose and reusable fittings. Can be used with fuel, lube and coolants. Working temperature is -45° to +300°F and have a 200 psi working pressure.

    Starlite hose can be used with either crimp style or reusable hose fittings. Crimp style fitting must be used only with Starlite hose and installed by qualified personnel using an Aeroquip ProCrimp 1380 crimping machine.

    There are only two ways to order these fittings and hose:

    1. Bring or mail us your old hose to match.
    2. We will send you the fittings and hose you think will work. You cut the hose to length and send it back to us for crimping.

    Fitting Thread Application Chart (GIF)

  • Aeroquip FBM4131 Starlite Crimp Fitting, 90 Degree, -4 AN
    Aeroquip FBM4131 Starlite Crimp Fitting, 90 Degree, -4 AN
    x
                

    Aeroquip's incredible Starlite racing hose and fittings are up to 45% lighter than stainless steel braided hose and reusable fittings. Can be used with fuel, lube and coolants. Working temperature is -45° to +300°F and have a 200 psi working pressure.

    Starlite hose can be used with either crimp style or reusable hose fittings. Crimp style fitting must be used only with Starlite hose and installed by qualified personnel using an Aeroquip ProCrimp 1380 crimping machine.

    There are only two ways to order these fittings and hose:

    1. Bring or mail us your old hose to match.
    2. We will send you the fittings and hose you think will work. You cut the hose to length and send it back to us for crimping.

    Fitting Thread Application Chart (GIF)

  • Aeroquip FBM4232 Starlite Crimp Fitting, 90 Degree, -6 AN
    Aeroquip FBM4232 Starlite Crimp Fitting, 90 Degree, -6 AN
    x
                

    Aeroquip's incredible Starlite racing hose and fittings are up to 45% lighter than stainless steel braided hose and reusable fittings. Can be used with fuel, lube and coolants. Working temperature is -45° to +300°F and have a 200 psi working pressure.

    Starlite hose can be used with either crimp style or reusable hose fittings. Crimp style fitting must be used only with Starlite hose and installed by qualified personnel using an Aeroquip ProCrimp 1380 crimping machine.

    There are only two ways to order these fittings and hose:

    1. Bring or mail us your old hose to match.
    2. We will send you the fittings and hose you think will work. You cut the hose to length and send it back to us for crimping.

    Fitting Thread Application Chart (GIF)

  • Chrome 90 Degree Heater Hose Fitting, 5/8 Inch Hose
    Chrome 90 Degree Heater Hose Fitting, 5/8 Inch Hose
    x
                

    Boy these fittings are hard to find! 90° style for or 5/8" hose. 1/2" NPT thread. Can be used for intake and water pump.

  • Tight Fit 90 Degree Socketless Reusable Fittings
    Tight Fit 90 Degree Socketless Reusable Fittings
    x
                

    These tight fit 90° steel fittings work great for a variety of different applications.  They feature your choice of -4, -6, or -8 AN male/female ends with a corrosion resistant finish.

    • Working pressure of 5500 psi 
    • 90° steel fuel line hose connector
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Choose from -4 AN, -6 AN, or -8 AN sizes

    Socketless Fitting Application Chart (GIF)

    AN Thread Size Guide (GIF)

    Fitting Thread Size Guide (GIF)

  • Aeroquip FCE4033 Nickel 90 Degree Hose End Coupler Fitting, -8 AN
    Aeroquip FCE4033 Nickel 90 Degree Hose End Coupler Fitting, -8 AN
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain.

    Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters from Aeroquip. Lighter and more affordable than stainless steel, these electoless nickel plated pieces combine great corrosion resistance with a neutral color and classy appearance.

    These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a nickel-plated finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617308).

    • -8 AN Aluminum
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Nickel corrosion resistant finish

    Fitting Thread Application Chart (GIF)

  • Fragola 689006-BL Real-Street 90 Degree PTFE Hose End Fitting, -6 AN, Black
    New
    Fragola 689006-BL Real-Street 90 Degree PTFE Hose End Fitting, -6 AN, Black
    x
                

    Fragola's Real-Street reusable hose ends for P.T.F.E. hose offer a bright dip anodized black finish and eliminate the permeation issues common with aftermarket racing hose.  A unique "double-swivel" design allows for clocking adjustment during installation.

    • 90° hose end
    • -6 AN
    • Black anodized finish
    • Double-swivel design
    • Reusable
    • For P.T.F.E. hose
  • Fragola 689010-BL Real-Street 90 Degree PTFE Hose End Fitting, -10 AN, Black
    New
    Fragola 689010-BL Real-Street 90 Degree PTFE Hose End Fitting, -10 AN, Black
    x
                

    Fragola's Real-Street reusable hose ends for P.T.F.E. hose offer a bright dip anodized black finish and eliminate the permeation issues common with aftermarket racing hose.  A unique "double-swivel" design allows for clocking adjustment during installation.

    • 90° hose end
    • -10 AN
    • Black anodized finish
    • Double-swivel design
    • Reusable
    • For P.T.F.E. hose
  • Fragola 689008-BL Real-Street 90 Degree PTFE Hose End Fitting, -8 AN, Black
    New
    Fragola 689008-BL Real-Street 90 Degree PTFE Hose End Fitting, -8 AN, Black
    x
                

    Fragola's Real-Street reusable hose ends for P.T.F.E. hose offer a bright dip anodized black finish and eliminate the permeation issues common with aftermarket racing hose.  A unique "double-swivel" design allows for clocking adjustment during installation.

    • 90° hose end
    • -8 AN
    • Black anodized finish
    • Double-swivel design
    • Reusable
    • For P.T.F.E. hose
  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -12 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -12 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then given a nickel finish to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -12 AN female to push-on adapter
    • 90 degree angle fuel line hose connector
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a corrosion resistant nickel finish

    Full Swivel Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Nickel, -6 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Nickel, -6 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then given a nickel finish to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -6 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a corrosion resistant nickel finish

    Full Swivel Application Chart (GIF)

  • Steel -6 AN Fitting for Aeroquip FC300 High Pressure Hose, 90 Degree
    Steel -6 AN Fitting for Aeroquip FC300 High Pressure Hose, 90 Degree
    x
                

    Steel power steering hose end fitting for use with Aeroquip FC300 high pressure hose. 90° elbow -6 AN swivel fitting easily assembles onto -6 AN hose with a bench vise and/or wrenches.  Steel hose ends are reusable.

    • -6 AN female to push-on adapter
    • 90° elbow fuel line hose connector
    • 37° angled sealing surface guarantees a positive anti-leak seal

    Fitting Thread Size Chart (GIF)

    FC300 Assembly Chart (GIF)

  • Speedway Full Flow Swivel Hose End FItting, 90 Degree Angle, Nickel, -8 AN
    Speedway Full Flow Swivel Hose End FItting, 90 Degree Angle, Nickel, -8 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then given a nickel finish to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -8 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a corrosion resistant nickel finish

    Full Swivel Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -10 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -10 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then given a nickel finish to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -10 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a corrosion resistant nickel finish

    Full Swivel Application Chart (GIF)

  • Air Conditioning Kit w/o Condenser
    Air Conditioning Kit w/o Condenser
    x
                

    The days of riding around trying to look cool while sweating your butt off are gone! So is going to the junkyard and trying to find used parts to cobble up an a/c system. These kits have three dash vents and two defrost ducts and are engineered for 1930's coupes, pickups and smaller cars.

    These are designed with both the a/c evaporator and heater core in one unit which helps keep size and installation time down. They fit under the dash just like a new car and allow disassembly without removing the unit from the car.

    They include dash louvers, defrost louvers, switch panel, a/c hose kit, dryer with switch, compressor with V-belt pulley, and evaporator/heater assembly. They are available with or without condenser and standard finish or deluxe polished aluminum compressor.

    Hoses will need to be crimped by your local shop. R134a Freon required, but not supplied. Compressor brackets and heater hoses sold separately.

    428-100 Instructions (PDF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Black Anodized, -8 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Black Anodized, -8 AN
    x
                Please view the product's page for more information
            
  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Red/Blue, -12 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Red/Blue, -12 AN
    x
                Please view the product's page for more information
            
  • Wing Slider Kevlar Hose Kit
    $59.99
    Wing Slider Kevlar Hose Kit
    x
                

    New kit supplies you with hoses and fittings to plumb your valve to your cylinder. Kit comes with two hoses, two 90 degree fittings for the wing cylinder, and four fittings for the valve.

    Due to variances in steering gears, you will have to pick out length of hoses you need for your pressure and return lines. Available in either braided or Kevlar. This kit fits most cars (Eagle, J&J, Maxim, etc.) utilizing an 8" or 10" stroke cylinder.

    Kevlar Slider Hose 940-1895

    • (2) 90° flare -4 to 1/8" NPT
    • (4) #4 flare to 1/8" NPT
    • (1) 24" kevlar line
    • (1) 38" kevlar line
  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Black, -10 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Black, -10 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then black anodized to give them a new sleek look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -10 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Black corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Red/Blue, -8 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Red/Blue, -8 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then red and blue anodized to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -8 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Red/Blue, -10 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Red/Blue, -10 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then red and blue anodized to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -10 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Black, -12 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree Angle, Black, -12 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then black anodized to give them a new sleek look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -12 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Black corrosion resistant finish

    Full Swivel Application Chart (GIF)

  • Aluminum Socketless Reusable Push-On Hose Barb Ends for AN Fittings
    Aluminum Socketless Reusable Push-On Hose Barb Ends for AN Fittings
    x
                

    These lightweight socketless fittings are machined from aluminum alloy and anodized red and blue with a luster finish, the ultimate in professional appearance. Precision machine work ensures a positive seal when coupling Full Flow™ hose ends to your carburetor. They are ideal for use as fuel line connectors or adapters.

    • AN to hose barb 
    • Choose straight, 45°, 90°, 120° or 180°. Then choose -6, -8, -10 or -12 AN size.
    • Use with Aeroquip Special Application blue hose
    • For use with 37° AN style fittings

    Socketless Fitting Application Chart (GIF)

    AN Thread Size Guide (GIF)

    Fitting Thread Size Guide (GIF)

  • 90 Degree Socketless Push-On Hose End Fitting, -8 AN
    90 Degree Socketless Push-On Hose End Fitting, -8 AN
    x
                

    90° socketless push-on hose ends for 37° fittings.

    • -8 AN female to push-on hose barb adapter
    • 90° fuel line hose connector
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Red/Blue corrosion resistant finish

    Socketless Push-On Hose Ends Application Chart (GIF)

  • Black 90 Degree -3 AN Flare to 1/8 Inch NPT Pipe Adapter Fitting
    Black 90 Degree -3 AN Flare to 1/8 Inch NPT Pipe Adapter Fitting
    x
                

    Aluminum pipe thread to 37° AN adapter fitting. Black anodized finish will give your engine compartment the look you are after.

    • 90 degree elbow
    • -3 AN flare to 1/8" NPT thread
    • Fuel line hose connector

    Fitting Thread Application Chart (GIF)

  • Goodridge 15 Inch Braided Brake Line with 90 Degree End
    Goodridge 15 Inch Braided Brake Line with 90 Degree End
    x
                

    These high quality stainless steel, braided fluid lines have a 90° fitting on one end and a straight fitting on the other. They work well for brake lines, clutch lines and gauge lines. These are available with AN3 or AN4 fittings. Sold individually.

    • Stainless steel
    • 90° fitting on one end and a straight fitting on the other
    • Brake lines, clutch lines and gauge lines
    • Available with AN3 or AN4 fittings
    • Sold individually

    Select applicable length. AN size is the "-#" at the end of the part number.

  • Aeroquip FCE4034 Nickel Plated -10 AN Hose End Fitting, 90 Degree
    Aeroquip FCE4034 Nickel Plated -10 AN Hose End Fitting, 90 Degree
    x
                

    Many street rodders find that red or blue anodized aluminum AN hose fittings look too racy on their cars, but standard steel versions are just too plain.

    Speedway offers a great looking alternative with these nickel plated aluminum hose fittings and adapters from Aeroquip. Lighter and more affordable than stainless steel, these electoless nickel plated pieces combine great corrosion resistance with a neutral color and classy appearance.

    These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a nickel-plated finish. For use with Aeroquip AQP® Stainless Steel Racing Hose and Aeroquip StartLite® light-weight hose (part number 617310).

    • -10 AN Aluminum
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a Nickel corrosion resistant finish

    Fitting Thread Application Chart (GIF)

  • Black 90 Degree Socketless Push-On Hose End, -8 AN
    Black 90 Degree Socketless Push-On Hose End, -8 AN
    x
                

    Black socketless push-on hose end fittings will give your engine compartment the look you are after. 90 degree fittings in multiple sizes.  For use with 37 degree flared ends.

  • Fragola 109004 Hose End Coupler Fitting, 90 Degree, Blue/Red, -4 AN
    Fragola 109004 Hose End Coupler Fitting, 90 Degree, Blue/Red, -4 AN
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings. Available in swivel with a blue/red anodized finish. For use with Fragola Premium Black Synthetic -4 AN Hose (part number 620504).

    • -4 AN
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • Unique taper design ensures easy assembly
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Accepts a variety of lightweight aluminum AN style adapters & fittings
    • Available in Blue/Red corrosion resistant finish

    90° Full Flow Ends come in sizes of AN4, AN6, AN8, AN10, AN12 and AN16.

    Fitting Thread Application Chart (GIF)

Goto Previous PagePrevious Page
1 2 3 4 5 6