Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"5 8 inch covers" Page 1 of 3

  • GM Alternator, 5/8 Inch Wide Alternator Belt Pulley, Plain
    GM Alternator, 5/8 Inch Wide Alternator Belt Pulley, Plain
    x
                

    So you've converted your Flathead-powered rod over to 12 volts and bolted a GM alternator in place. Now it's time to install the belt, but your engine pulley is 5/8" and the alternator is 1/2"!

    Don’t worry, Speedway has you covered. This alternator pulley allows the use of a 5/8" wide Flathead-style belt on GM externally regulated, SI and one-wire alternators.

  • Knockoff Hub Covers, 5 on 4-1/2 and 5 on 4-3/4 Inch
    Knockoff Hub Covers, 5 on 4-1/2 and 5 on 4-3/4 Inch
    x
                These "knockoff" hub covers are designed to mount on the flat face of "mag" or "Halibrand" style wheels. They are held on by the same long-shank lug nuts that hold the wheel on. The lug nuts are concealed behind the cover which is held on by the knockoff. 

    Most current wheels don't use the long shank lugs. To mount these on wheels not using the long-shank mag nuts, you will have to drill and tap holes on the face of the wheel and provide your own screws to mount the base plates.

    Highly polished cast aluminum construction. Set of four.
  • Shockwears Armor Protectors
    $34.99
    Shockwears Armor Protectors
    x
                

    A premium cover that will protect your shocks like never before! Flexible armor plated material, adjustable velcro closure and vented to release heat. 
    For 2-5/8" diamter springs only!

    Available in four lengths: 14", 17", 19" and 21". 

  • Stainless Braided Radiator Hose Cover, 1-1/4 to 1-5/8 Inch O.D.
    Stainless Braided Radiator Hose Cover, 1-1/4 to 1-5/8 Inch O.D.
    x
                Use in conjunction with Tube Seal™ Hose Ends.  Duplicates the appearance of far more expensive stainless steel braided  hose and fittings. Fits over 1-1/4" - 1-5/8" O.D. hose. 

    Sold in 6 ft. sleeves.

    Note: Coverage may vary on diameter on hose. 6 ft. of sleeving typically covers 4 ft of hose.
  • Ford 9 Inch Bolt-On Rear Disc Brake Kit
    Ford 9 Inch Bolt-On Rear Disc Brake Kit
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM metric style calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31902 Instructions (PDF)

  • Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
    Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM emergency brake calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31921 Instructions (PDF)

  • O/E Style Hot Rod Steel 15 Inch Wheel, Chrome, 15 x 8, 5 on 4-1/2
    O/E Style Hot Rod Steel 15 Inch Wheel, Chrome, 15 x 8, 5 on 4-1/2
    x
                
    • O.E.M. style wheel
    • 15 Inch Wheel
    • 8 Inch Wide
    • 5 on 4.5" (Ford/Mopar) wheel bolt pattern
    • 2.840" center hole
    • Chrome plated steel construction 
    • Accepts 10-1/8" spider ring
    • Use in conjunction with O/E taper lug nuts
    • Disc brake friendly
    • Hub cover not included
    • Add spider rings and caps (sold separately) for a neat '60s style look
  • O/E Style Hot Rod 15 Inch Steel Wheel, Chrome, 15 x 5, 5 on 4-3/4
    O/E Style Hot Rod 15 Inch Steel Wheel, Chrome, 15 x 5, 5 on 4-3/4
    x
                
    • O.E.M. style wheel
    • 15 Inch Wheel
    • 5 Inch Wide
    • 5 on 4.75" (GM) wheel bolt pattern
    • 2.840" center hole
    • Chrome plated steel construction 
    • Accepts 10-1/8" spider ring
    • Use in conjunction with O/E taper lug nuts
    • Disc brake friendly
    • Hub cover not included
    • Add spider rings and caps (sold separately) for a neat '60s style look
  • Unisteer 8050290 Steering U-Joint, 5/8 Inch-36 Spline to 3/4 Inch DD
    Unisteer 8050290 Steering U-Joint, 5/8 Inch-36 Spline to 3/4 Inch DD
    x
                

    These polished stainless steel U-joints look great and use a pinch bolt on each end for easy installation.

    • The OD is 1.650" (41.90mm) 
    • 3-3/4" in total length

    This universal joints size is 5/8"-36 count spline by 3/4" DD Shaft. It is the common size for the Vega style steering box.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

  • GM Alternator 5/8 Inch Wide Belt Pulley, Aluminum
    GM Alternator 5/8 Inch Wide Belt Pulley, Aluminum
    x
                

    So, you've converted over to a 12-volt electrical system and bolted a GM alternator to your flathead Ford V8. Now it's time to install the belt and pulley, but your engine uses a 5/8" belt and the alternator pulley is 1/2"! Don't worry – Speedway has you covered. This aluminum pulley is designed to fit on a GM alternator and use a 5/8" drive belt.

    • Used on popular GM externally regulated, "SI" and one-wire alternators
    • Fits 1963 and newer GM alternators
    • Allows the use of the 5/8" wide flathead Ford style V-belts
    • Attractive and durable aluminum construction
  • GM Alternator 5/8 Inch Wide Belt Pulley, Chrome
    GM Alternator 5/8 Inch Wide Belt Pulley, Chrome
    x
                

    So, you've converted over to a 12-volt electrical system and bolted a GM alternator to your flathead Ford V8. Now it's time to install the belt and pulley, but your engine uses a 5/8" belt and the alternator pulley is 1/2"! Don't worry – Speedway has you covered. This chrome pulley is designed to fit on a GM alternator and use a 5/8" drive belt.

    • Allows the use of 5/8" wide flathead-style belts on popular GM externally regulated, "SI" and one-wire alternators
    • Durable and attractive chrome finish
    • Fits 1963 and newer GM alternators

     

  • Knockoff Hub Covers, 5 on 5 and 5 on 5-1/2 Inch
    Knockoff Hub Covers, 5 on 5 and 5 on 5-1/2 Inch
    x
                These "knockoff" hub covers are designed to mount on the flat face of "mag" or "Halibrand" style wheels. They are held on by the same long-shank lug nuts that hold the wheel on. The lug nuts are concealed behind the cover which is held on by the knockoff. 

    Most current wheels don't use the long shank lugs. To mount these on wheels not using the long-shank mag nuts, you will have to drill and tap holes on the face of the wheel and provide your own screws to mount the base plates.

    Highly polished cast aluminum construction. Set of four.
  • Sweet Mfg Steering U-Joint, 5/8-36 Spline, 1 Inch DD, Vega/Corvair/GM Rack
    Sweet Mfg Steering U-Joint, 5/8-36 Spline, 1 Inch DD, Vega/Corvair/GM Rack
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 5/8"-36 spline and feature forged Vanadium steel yokes.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 5/8"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Edelbrock 41179 Cast 14 Inch Round Air Cleaner
    New
    Edelbrock 41179 Cast 14 Inch Round Air Cleaner
    x
                Edelbrock’s Classic Series engine dress-up accessories deliver a definitive appeal that brings back a look from the 1950’s.

    Edelbrock first made these aluminum valve covers in the late '50s and they continue to be a classic. Made of heavy-gauge sand-cast aluminum, our classic finned valve covers are now available in a natural as-cast finish, for enthusiasts looking for a subtle classic look for their engine.

    All of the air cleaners include a pre-oiled and washable cotton gauze element for excellent filtration. They are compatible with all popular 5-1/8" diameter carburetors and throttle bodies.

    Classic Series Accessory Details:
    • Now available in a natural as-cast finish for an authentic look from the 1950’s
    • Made from heavy-gauge sand-cast aluminum in the USA
    • Air cleaners include a 3” washable and reusable filter element that fits 5-1/8” diameter carburetors and throttle bodies
  • DECO Frame Height Gauge, 4-1/4 Inch to 5-5/8 Inch
    DECO Frame Height Gauge, 4-1/4 Inch to 5-5/8 Inch
    x
                Quick and accurate way to measure frame height. Covers frame heights from 4-1/4" to 5-5/8"  in 1/8" increments. Stury steel construction. No flimsy  plastic here!
            
  • DECO Frame Height Gauge, 5-5/8 Inch to 7 Inch
    DECO Frame Height Gauge, 5-5/8 Inch to 7 Inch
    x
                Quick and accurate way to measure frame height. Covers frame heights from  5-5/8" to 7" in 1/8" increments. Sturdy steel construction. No flimsy  plastic here!
            
  • Billet Specialties 67525 5/8 Inch Braided Hose Aluminum Hose End Cover
    Billet Specialties 67525 5/8 Inch Braided Hose Aluminum Hose End Cover
    x
                

    Billet Specialties has the answer for unsightly hose clamps and loud anodized colors - polished billet hose ends! For use with 5/8" braided hose (heater hose).

    • Precision machined from 6061-T6 billet aluminum
    • Mirror polish finish
    • Hose clamp included
    • Sold individually
  • Billet Specialties 67425 Polished Aluminum 5/8 Inch Hose End Cover
    Billet Specialties 67425 Polished Aluminum 5/8 Inch Hose End Cover
    x
                

    Billet Specialties has the answer for unsightly hose clamps and loud anodized colors - polished billet hose ends! For use with 5/8" rubber hose (heater hose).

    • Precision machined from 6061-T6 billet aluminum
    • Mirror polish finish
    • Hose clamp included
    • Sold individually
  • AFCO OWSCR14 Coilover Shock Cover for 2-5/8 Spring, 14 Inch Length
    AFCO OWSCR14 Coilover Shock Cover for 2-5/8 Spring, 14 Inch Length
    x
                Keep dirt out from your coil over shocks with these blue AFCO coilover shock covers for 2-5/8" diameter springs only.
            
  • U-Joint, 5/8"-36 Spline to 3/4" Round Weld-On
    U-Joint, 5/8"-36 Spline to 3/4" Round Weld-On
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. This steering universal joint is the highest quality for racing or street use.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 5/8"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • O/E Style Hot Rod Steel 15 Inch Wheel, Chrome, 15 x 5, 5 on 4-1/2
    O/E Style Hot Rod Steel 15 Inch Wheel, Chrome, 15 x 5, 5 on 4-1/2
    x
                
    • O.E.M. style wheel
    • 15 Inch Wheel
    • 5 Inch Wide
    • 5 on 4.5" (Ford/Mopar) wheel bolt pattern
    • 2.840" center hole
    • Chrome plated steel construction 
    • Accepts 10-1/8" spider ring
    • Use in conjunction with O/E taper lug nuts
    • Disc brake friendly
    • Hub cover not included
    • Add spider rings and caps (sold separately) for a neat '60s style look
  • Dynatech   Late Model Exhaust, 1-5/8 to 1-3/4 Inch, Chevy 18 Degree 550HP+
    Dynatech Late Model Exhaust, 1-5/8 to 1-3/4 Inch, Chevy 18 Degree 550HP+
    x
                

    Dynatech® pavement car exhaust systems start with Dynatech®’s 35” equal length headers. Although difficult to construct, equal length headers deliver maximum torque and horsepower and are used by the best drivers and teams in the country.

    All Dynatech® headers are built with CNC laser machined flanges. With port holes accurate to .003” and total warp less than .025”, you can be assured that you will get all the performance and quality possible from your headers.

    • CNC laser-cut flange
    • Built to fit with proper clearance
    • Optimized tube length for power
    • 35" equal length primaries for maximum torque and horsepower
    • Valve covers are removable with headers installed
    • Removable collectors
    • Tube Size: 1-3/4" - 1-7/8"
    • HP Range: 550 +

     

  • AFCO OWSCR19 Coil-Over Shock Cover for 2-5/8 Spring, 19 Inch Length
    AFCO OWSCR19 Coil-Over Shock Cover for 2-5/8 Spring, 19 Inch Length
    x
                Keep dirt out from your coil-over shocks with these blue AFCO coilover shock covers for 2-5/8" diameter springs only.
            
  • AFCO OWSCR21 Coil-Over Shock Cover for 2-5/8 Spring, 21 Inch Length
    AFCO OWSCR21 Coil-Over Shock Cover for 2-5/8 Spring, 21 Inch Length
    x
                Keep dirt out from your coil-over shocks with these blue AFCO coilover shock covers for 2-5/8" diameter springs only.
            
  • GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit
    GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit
    x
                

    If you don't want to spend and arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes two bolt-on caliper brackets, two 11-5/8" vented rotors, two GM metric style calipers, brake pads and hardware.

    • 5 on 4-3/4" bolt circle
    • Fits over an axle with a maximum flange diameter of 6" O.D.
    • 2.872" rotor center hole
    • Requires a minimum 14-5/8" I.D. for caliper clearance 

    910-31923 Instructions (PDF)

  • GM 10-Bolt with 8.5 Inch Ring Gear Rear End Differential Axle Cover
    GM 10-Bolt with 8.5 Inch Ring Gear Rear End Differential Axle Cover
    x
                

    Add some visual attitude to your rear axle with these chrome differential covers. They're stamped from heavy-gauge steel to ward off those pesky oil leaks, and chrome plated for long lasting good looks.

    GM 10-Bolt 8.5 Inch Rearend Differential Cover

    Fits:

    • Full size and intermediate Chevy and GM cars 1971-1994
    • Axle types B, C, G, K and O.

     

  • GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit w/ E-Brake
    GM 7.5 Inch 10 Bolt Bolt-On Rear Brake Kit w/ E-Brake
    x
                

    If you don't want to spend and arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes two bolt-on caliper brackets, two 11-5/8" vented rotors, two GM emergency brake calipers, brake pads and hardware.

    • 5 on 4-3/4" bolt circle
    • Fits over an axle with a maximum flange diameter of 6" O.D.
    • 2.872" rotor center hole
    • Requires the use of 16" wheels as this kit has a minimum 14-5/8" I.D. for caliper clearance 

    910-31928 Instructions (PDF)

  • O/E Style Hot Rod 15 Inch Chrome Steel Wheel, 15x7, 5 on 4-1/2
    O/E Style Hot Rod 15 Inch Chrome Steel Wheel, 15x7, 5 on 4-1/2
    x
                
    • O.E.M. style wheel
    • 5 on 4.5" (Ford/Mopar) wheel bolt pattern
    • 2.840" center hole
    • Chrome plated steel construction 
    • Accepts 10-1/8" spider ring
    • Use in conjunction with O/E taper lug nuts
    • Disc brake friendly
    • Hub cover not included
    • Add spider rings and caps (sold separately) for a neat '60s style look
  • Garage Sale - Weld 13 x 7, 4 Inch Offset, Direct Mount Midget Front Wheel Cover
    Garage Sale - Weld 13 x 7, 4 Inch Offset, Direct Mount Midget Front Wheel Cover
    x
                Please view the product's page for more information
            
  • O/E Style Hot Rod Steel 15 Inch Wheel, Chrome, 15 x 7, 5 on 4-3/4
    O/E Style Hot Rod Steel 15 Inch Wheel, Chrome, 15 x 7, 5 on 4-3/4
    x
                
    • O.E.M. style wheel
    • 15 Inch Wheel
    • 5 on 4.75" (GM) wheel bolt pattern
    • 2.840" center hole
    • Chrome plated steel construction 
    • Accepts 10-1/8" spider ring
    • Use in conjunction with O/E taper lug nuts
    • Disc brake friendly
    • Hub cover not included
    • Add spider rings and caps (sold separately) for a neat '60s style look
  • O/E Style Hot Rod 15 Inch Chrome Steel Wheel, 15x8, 5 on 4-3/4
    O/E Style Hot Rod 15 Inch Chrome Steel Wheel, 15x8, 5 on 4-3/4
    x
                
    • O.E.M. style wheel
    • 5 on 4.75" (GM) wheel bolt pattern
    • 2.840" center hole
    • Chrome plated steel construction 
    • Accepts 10-1/8" spider ring
    • Use in conjunction with O/E taper lug nuts
    • Disc brake friendly
    • Hub cover not included
    • Add spider rings and caps (sold separately) for a neat '60s style look
  • Edmunds Custom Air Cleaner, Tall, 2-5/8 Inch Neck
    Edmunds Custom Air Cleaner, Tall, 2-5/8 Inch Neck
    x
                

    Reproduction of the famous Edmunds air cleaners for your vintage ride. The 2-5/8" base fits the common Stromberg 97, Ford 94 or Rochester 2G style carbs.  Mesh covered washable/reuseable filter element included.

  • Edmunds Custom Air Cleaner, Short, 2-5/8 Inch Neck
    Edmunds Custom Air Cleaner, Short, 2-5/8 Inch Neck
    x
                

    Reproduction of the famous Edmunds air cleaners for your vintage ride. The 2-5/8" base fits the common Stromberg 97, Ford 94 or Rochester 2G style carbs.  Mesh covered washable/reuseable filter element included.

  • Ram Clutches 301M 10.5 Inch Organic Clutch Disc, 1-1/8 Inch 10-Spline
    Ram Clutches 301M 10.5 Inch Organic Clutch Disc, 1-1/8 Inch 10-Spline
    x
                

    Full face 10-1/2" diameter clutch disc with a sprung hub for softer engagement. 300 Series organic material for single disc pressure plates. Weighs 4 lbs.

    Tech Tip:  When installing a new clutch, be sure to follow the manufacturer's instructions for correct set-up.  You should also replace the pilot bushing/bearing.

    Tech Tip:  To extend the life of your expensive racing clutch you should not use it to load the car on or in your trailer.  The amount of slippage this causes is worse than a night of racing.

     

  • Dynatech   Late Model Exhaust, 1-5/8 Inch Primary, Std. Chevy 300-350HP
    Dynatech Late Model Exhaust, 1-5/8 Inch Primary, Std. Chevy 300-350HP
    x
                

    Dynatech® pavement car exhaust systems start with their 35" equal length headers. Although difficult to construct, equal length headers deliver maximum torque and horsepower and are used by the best drivers and teams in racing. 

    All Dynatech® headers are built with CNC laser machined flanges. With port holes accurate to .003" and total warp less than .025", you can be assured that you will get all the performance and quality possible from your headers. 

    • CNC laser cut flanges
    • Built to fit with proper clearance
    • Optimized tube length for power 
    • 35" equal lengthprimaries for maximum torque and horsepower
    • Valve covers are removable with headers installed
    • Removable collectors
    • Tube Size: 1-5/8"
    • HP Range: 300-350

    Header Dimension Chart

  • Edmunds Custom Air Cleaner, Oval, 2-5/8 Inch Neck
    Edmunds Custom Air Cleaner, Oval, 2-5/8 Inch Neck
    x
                

    Reproduction of the famous Edmunds air cleaners for your vintage ride. The 2-5/8" base fits the common Stromberg 97, Ford 94 or Rochester 2G style carbs.  Mesh covered washable/reuseable filter element included.

  • Speedway Mini Magnetic Parts Tray, 5-7/8 Inch Diameter
    Speedway Mini Magnetic Parts Tray, 5-7/8 Inch Diameter
    x
                These magnetic parts trays are perfect for holding small parts, hardware and fasteners in place. They are a 5-7/8" stainless steel dish with a rubber covered magnetic base to prevent scratching.
    • 5-7/8" stainless steel dish
    • Perfect for holding small parts, hardware and fasteners in place
    • Sticks to any ferrous metal surface - it even works upside down
    • Rubber covered magnetic base prevents scratching
  • Seals-It WS6250 Heim Joint Rod End Seals, 5/8 Inch Hole, Set/6
    Seals-It WS6250 Heim Joint Rod End Seals, 5/8 Inch Hole, Set/6
    x
                

    These rod end seals are a neoprene rubber seal bonded to an aircraft quality washer. Extends the life of your rod ends by keeping the dirt, debris and moisture out of the spherical ball. They fit on both sides of the ball end of the heim joint and are sized to match the hole in the spherical ball.  

    For use with standard and Pro 1 Series rod end only. Sold in sets of six, which will cover both sides of three rod ends.

  • DEi 050370 Boom Mat Speaker Baffle, 6 X 8 Inch Oval
    DEi 050370 Boom Mat Speaker Baffle, 6 X 8 Inch Oval
    x
                Please view the product's page for more information
            
  • Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 1 DD, Vega, Corvair, GM
    Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 1 DD, Vega, Corvair, GM
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 5/8"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Goto Previous PagePrevious Page
1 2 3