Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"1 inch double joints" Page 1 of 2

  • Unisteer 8050310 Steering U-Joint-1 Inch Double D to 3/4 Inch Double D
    Unisteer 8050310 Steering U-Joint-1 Inch Double D to 3/4 Inch Double D
    x
                

    These polished stainless steel U-joints look great and use a pinch bolt on each end for easy installation.

    This is a size that is used on some large GM steering columns. This specific steering universal joint uses a pinch bolt fastener on the 3/4"DD side and a set screw on the 1"DD side, due to the large size

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

    Fits IDIDIT/Flaming River 1" Double D

  • Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • 1.354" not including the screws (1.534" including), width on the u-joint.
    • 1.125" OD on the ends not including the nut (1.345" including the nut). 

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Double U-Joint, 1 Inch-48 Spline to 3/4 Inch DD
    Sweet Mfg Chrome Double U-Joint, 1 Inch-48 Spline to 3/4 Inch DD
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-3/4" Long

    Steering U-Joints and Couplers Application Chart (GIF)

    Steering Box/Rack/Spline Chart (Link)

    Spline Size (Link)

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 1 Inch DD, GM Column
    Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 1 Inch DD, GM Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 1" DD
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Steering U-Joint, 3/4 Inch DD to 1 Inch DD, GM Column / Universal
    Sweet Mfg Steering U-Joint, 3/4 Inch DD to 1 Inch DD, GM Column / Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 3.875 inches long and 1.375 inches in diameter. 

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • U-Joint=3.875" L x 1.375" D
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 1 Inch DD, Ididit/Flaming River Column
    Sweet Mfg Chrome Steering U-Joint, 1 Inch DD, Ididit/Flaming River Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 3/4 DD, GM Column
    Sweet Mfg Chrome Steering U-Joint, 1 Inch-48 Spline to 3/4 DD, GM Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 1" DD
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Unisteer 8050300 Steering U-Joint, 3/4 Inch Double D to 3/4 Inch DD
    Unisteer 8050300 Steering U-Joint, 3/4 Inch Double D to 3/4 Inch DD
    x
                

    These polished stainless steel steering U-joints look great and use a pinch bolt on each end for easy installation.

    This particular steering universal joint is made to fit 3/4"DD shafting on both sides. Both sides incorporate the pinch bolt design.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-48 Spline to 1 Inch DD, Wilwood, MGB
    Sweet Mfg Chrome Steering U-Joint, 3/4-48 Spline to 1 Inch DD, Wilwood, MGB
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-48 Spline
    • Wilwood, Sweet, Jaguar, MGB
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 1 Inch DD, Universal
    Sweet Mfg Chrome Steering U-Joint, 3/4 Inch DD to 1 Inch DD, Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering  universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • 1.354" not including the screws (1.534" including), width on the u-joint.
    • 1.125" OD on the ends not including the nut (1.345" including the nut). 
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Double U-Joint, 3/4 Inch DD to 1 Inch DD, GM
    Sweet Mfg Chrome Double U-Joint, 3/4 Inch DD to 1 Inch DD, GM
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-3/4" Long
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Unisteer 8050330 Steering U-Joint-3/4 Inch Double D to 3/4 Inch Smooth
    Unisteer 8050330 Steering U-Joint-3/4 Inch Double D to 3/4 Inch Smooth
    x
                

    These polished stainless steel U-joints look & function beautifully and use non-pinch bolts which will need to be either welded, cross-drilled and pinned or bolted. These steering universal joints are 3-3/4 inches in length and have an outside diameter of 1.650 inches.

    • The OD is 1.650" (41.90mm) 
    • 3-3/4" in total length
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

  • Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch Round
    Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch Round
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Chrome Steering U-Joint, 13/16-36 Spline, 3/4 Inch DD, Big GM Pre '78
    Sweet Mfg. Chrome Steering U-Joint, 13/16-36 Spline, 3/4 Inch DD, Big GM Pre '78
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. They feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 13/16"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Double U-Joint, 3/4 Inch DD to 1 Inch DD, IDIDIT/Flaming River
    Sweet Mfg Chrome Double U-Joint, 3/4 Inch DD to 1 Inch DD, IDIDIT/Flaming River
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-3/4" Long
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 Inch-48 Spline to 3/4 Inch Round, GM Column
    Sweet Mfg. Double Steering U-Joint, 1 Inch-48 Spline to 3/4 Inch Round, GM Column
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    • Overall length is 5-1/2”
    • O.D. at ends is 1.12”
    • O.D. in the middle is 1.476”
    • O.D. at caps is 1.350”
    • O.D. at cap retainer screws is 1.545”
    • Length of center section is 2-3/4”
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

     

  • Sweet Mfg. Double Steering U-Joint, 1 Inch 48-Spline to 3/4 Inch DD, GM Column
    Sweet Mfg. Double Steering U-Joint, 1 Inch 48-Spline to 3/4 Inch DD, GM Column
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch DD, GM Column
    Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch DD, GM Column
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Steering U-Joint, 3/4 Inch Round to 1 Inch DD, GM Column/Universal
    Sweet Mfg Steering U-Joint, 3/4 Inch Round to 1 Inch DD, GM Column/Universal
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have a 3/4 round weld-on end.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • U-Joint=3.875" L x 1.375" D
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Inch DD, GM, MII
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Inch DD, GM, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. This Mustang II power rack U joint is made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. 401-91919 Chrome Double U-Joint, 3/4 Inch DD to 3/4 Inch DD
    Sweet Mfg. 401-91919 Chrome Double U-Joint, 3/4 Inch DD to 3/4 Inch DD
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-5/8" Long
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Double U-Joint, 9/16 Inch-26 Spline to 3/4 Inch DD
    Sweet Mfg Chrome Double U-Joint, 9/16 Inch-26 Spline to 3/4 Inch DD
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-3/4" Long
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Double U-Joint, 5/8 Inch-36 Spline to 3/4 Inch DD
    Sweet Mfg Chrome Double U-Joint, 5/8 Inch-36 Spline to 3/4 Inch DD
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-3/4" Long
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Double U-Joint, 3/4 Inch-30 Spline to 3/4 Inch DD
    Sweet Mfg Chrome Double U-Joint, 3/4 Inch-30 Spline to 3/4 Inch DD
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

    • These are 5-3/4" Long
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. U-Joint, 3/4 Inch-20 Spline to 3/4 Inch Round, Weld-On
    Sweet Mfg. U-Joint, 3/4 Inch-20 Spline to 3/4 Inch Round, Weld-On
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. All of these steering universal joints have 3/4 weld-on ends. U-joints available for round or double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing
    • Features needle bearing u-joints
    • U-Joint=3.875" L x 1.375" D
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

     

  • Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3/4 Inch Round, MII
    Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3/4 Inch Round, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

     

  • Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3-4 Inch DD, MII
    Sweet Mfg. Double Steering U-Joint, 9/16 Inch-26 Spline to 3-4 Inch DD, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch Round to 3/4 Inch DD, Universal
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch Round to 3/4 Inch DD, Universal
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. Made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Steering U-Joint, 1 Inch DD, 3/4 Round, IDIDIT/Flaming River Column
    Sweet Mfg Steering U-Joint, 1 Inch DD, 3/4 Round, IDIDIT/Flaming River Column
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have a 3/4" round weld-on end.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 1 DD, Vega, Corvair, GM
    Sweet Mfg Chrome Steering U-Joint, 5/8-36 Spline to 1 DD, Vega, Corvair, GM
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 5/8"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-36 Spline, 1 DD, GM Manual/Mustang II
    Sweet Mfg Chrome Steering U-Joint, 3/4-36 Spline, 1 DD, GM Manual/Mustang II
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. They feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-36 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 17MM DD, 3/4DD, Corvette, Citation Rack
    Sweet Mfg Chrome Steering U-Joint, 17MM DD, 3/4DD, Corvette, Citation Rack
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg Chrome Steering U-Joint, 3/4-30 Spline to 3/4 DD, Small GM P/S '78-Up
    Sweet Mfg Chrome Steering U-Joint, 3/4-30 Spline to 3/4 DD, Small GM P/S '78-Up
    x
                

    Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

    • Full compliment bearings
    • Forged Vanadium steel yokes and u-joint
    • Highest quality for racing or street
    • Features needle bearing u-joints
    • 3/4"-30 Spline
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 Round, IDIDIT/Flaming River
    Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 Round, IDIDIT/Flaming River
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    • Overall length is 5-1/2”
    • O.D. at ends is 1.12”
    • O.D. in the middle is 1.476”
    • O.D. at caps is 1.350”
    • O.D. at cap retainer screws is 1.545”
    • Length of center section is 2-3/4”
    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Double Steering U-Joint, .620 Inch-36 Spline to 3/4 Inch Round, Chrysler
    Double Steering U-Joint, .620 Inch-36 Spline to 3/4 Inch Round, Chrysler
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

     

  • Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Round, GM, MII
    Sweet Mfg. Double Steering U-Joint, 3/4 Inch 36-Spline to 3/4 Round, GM, MII
    x
                

    Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. This Mustang II power rack steering universal joint is made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

    Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

    Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

  • Steel Double D Shaft, 3/4 Inch O.D., 18 - 36 Inch Lengths
    Steel Double D Shaft, 3/4 Inch O.D., 18 - 36 Inch Lengths
    x
                

    This 3/4" O.D. DD shaft has a 1.00" long "D" design on each end. Made from 1018 steel, weld-on. Excellent for steering shafts or other uses. Order desired length. 

    NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

  • Steel Double D Shaft, 3/4 Inch O.D., 4 - 16 Inch Lengths
    Steel Double D Shaft, 3/4 Inch O.D., 4 - 16 Inch Lengths
    x
                

    This 3/4" O.D. DD shaft has a 1.00" long "D" design on each end. Made from 1018 steel, weld-on. Excellent for steering shafts or other uses. Order desired length. 

    NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

  • Polished Stainless Steel 3/4 O.D. Double D Shaft
    Polished Stainless Steel 3/4 O.D. Double D Shaft
    x
                It's pretty silly to use plain old steel double d shaft with those shiny stainless steel u-joints. We offer this polished stainless steel double D shaft in 18", 22" and 36" cut to fit lengths. 
            
Goto Previous PagePrevious Page
1 2