No items in Shopping Cart
Our Deluxe Coil Spring kit includes a weld-on 25.5" Panhard bar, 2 coil springs (175 lb. rate, 14" tall, 4.5" O.D.), upper and lower spring mounts, two 32" steel radius rods with mounting brackets, and all hardware.
This rear suspension kit is loaded with high quality components from Mr. Roadster and Carrera. Includes Panhard bar, Carrera coil-over assemblies, 32" radius rods, and all mounting brackets and hardware.
Dirtworks 2-link rear suspension kit comes with all of the brackets, nuts, pull-bars, and other components necessary to set up a robust rear suspension system on your IMCA modified racer.Kit includes: 3/4" Swedged Steel Tubes Two 2-Link Brackets Std 3/4" RH & LH Male Heims 9" Ford Torque Link Plates 9" Ford Panhard Bar Mount Rubber Bushing J Bar 5" x 4" Torque Link Spring Pull Bar w/o Spring 3/4" RH & LH Jam Nuts Frame Mount P-Hard Bar Spring Slider Only w/o Ends Std 1/2" RH Male Heims 1/2" ...
Our affordable Speedway rear suspension system come with everything you'll need for your IMCA racer.Kit includes: RH & LH Steel Birdcages 9" Ford Torque-Link Plates 9" Ford Adj Panhard Mount Swedge Tube for 5/8" Heims Std 5/8" RH & LH Male Heims 60" GN Housing 60" GN Axles GN 5 x 5" BP Hardware 5" x 13" Tru-Coil Rear Springs 3/4" RH & LH Jam Nuts5/8" RH & LH Jam Nuts Bearing Type Pull Bar 6-3/4" Progressive Pull Bar SpringSwedged Tube for 5/8" Heim
Dirtworks 2-link rear suspension kit comes with allof the brackets, nuts, pull-bars, and other components necessary to set up a robust rear suspension system on your IMCA modified racer.Kit includes: LH 4-Bar U-Weld Birdcages 5/8" Swedged Steel Tubes 5/8" Swedged Steel Sleeves Std 5/8" RH & LH Male Heims 9" Ford Torque-Link Plates 9" Ford Panhard Bar Mount Rubber Bushing J Bar 5" x 4" Torque Link Spring Pull Bar w/o Spring Top Link Bushings & Washers Std 3/4" RH Male & Female Heims 3/4" RH & LH Jam Nuts ...
This kit is patterned after the setup that Johnny "The Jet" Saathoff used to drive to FOUR IMCA National Championships. It will come with everything that you'll need to set up your IMCA racers rear suspension.Kit includes:60" GN Housing 60" GN Axle GN 5 x 5" BP Hardware Swing Arms Birdcages for Swing Arms Swedged Tube for 5/8" Heims3/4" RH 5/8" Hole Pro 1 HeimsStd 5/8" RH & LH Male Heims Pull Bar Brackets Adjustable Pull Bar BoltPanhard Bar Bracket Swedged Tube for 3/4" Heim Std 3/4" RH & LH ...
Complete kit includes: mild steel or fully polished rods, steel brackets, bushed rod ends, and hardware. Lower coil-over shock mount stud not included. The nuts & bolts supplied in this kit are NOT polished or plated.
It doesn't get any simpler than this! Our most basic T-bucket frame is engineered for a simple and economical coil spring rear suspension with traditional-style radius rods. The front suspension is our time-tested transverse-leaf, spring-behind-axle setup with hairpin-style radius rods. Designed for the do-it-yourselfer, this frame has no front shock mounts - you can fabricate your own or choose from those offered by Speedway!
This kit is desgined for installing a new rear axle in your 1960-72 Chevy pickup (1/2-ton, coil-spring suspension only.) Requires minimal welding. Kit includes axle brackets & adjustable trac-bar.
Our affordable Speedway front suspension system come with everything you'll need for your IMCA racer.Kit includes: Collars for Adjustable A-Arm 5/8" RH Clevis 5/8" RH Jam Nuts Screw-in Balljoints RH & LH Lower Control A-Arms 1971-76 Ball Joints, Tall 1.650 x .500 Lower Bushings 1.34" x .500 Lower Bushings RH & LH Metric Reamed Spindle 1979-Up GM Metric 5 x 5" Rotors Seals Outer Bearing Cup & Cones Outer Bearing Tapered Inner Short Jack Bolts Weight Jack Tops 1978-Up Drag Link 1978-Up Idler Arm 3/4"-30 GM Power Steering Box 5/8" ...
This kit is patterned after the setup that Johnny "The Jet" Saathoff used to drive to FOUR IMCA National Championships. It will come with everything that you'll need to set up your IMCA racers front suspension.Kit includes: Collar for Adjustable A-Arm 5/8" Swedged Steel Sleeves 5/8" RH Clevis 5/8" RH Jam Nuts Std 5/8" LH Male Heims 3/4" Jack Bolts & Mounts RH & LH Lower A-Arm Screw-in Ball Joints 1973-77 Intermediate GM Spindles 1973-77 GM Midsize 11" Rotors, 5 on 5" 5/8" Lug Nuts 5-1/2" Tru-Coil Springs SealsOuter Bearing ...
Give your 1935-40 fat-fendered Ford state-of-the-art ride and handling with the Speedway composite leaf rear suspension kit. Composite springs are the new wave of performance spring material. They are lighter than steel, respond faster,last up to 5 times longer, and will not rust or corrode like traditional leaf springs. The monoleaf design also ensures noise- and friction-free performance, while providing the softest, smoothest ride imaginable.
Give your 1942-48 fat-fendered Ford state-of-the-art ride and handling with the Speedway composite leaf rear suspension kit. Composite springs are the new wave of performance spring material. They are lighter than steel, respond faster,last up to 5 times longer, and will not rust or corrode like traditional leaf springs. The monoleaf design also ensures noise- and friction-free performance, while providing the softest, smoothest ride imaginable.
Use this air spring kit with either standard or triangulated 4-bar rears. Includes two air springs, mountsand hardware.
Give your 1935-48 Fat-Fendered Ford state-of-the-art ride and handling with the Speedway Composite Leaf Rear Suspension Kit. Composite springs are the new wave of performance spring material. They are lighter than steel, respond faster,last up to 5 times longer, and will not rust or corrode like traditional leaf springs. The monoleaf design also ensures noise and friction-free performance, while providing the softest, smoothest ride imaginable.
Bolt on rock-steady handling and control to your 1935-40 and 1942-48 Fat-Fendered Ford. Recommended for use with the Mr. Roadster Composite Leaf Rear Suspension Kit.
Complete the front and rear suspension assembly on your T roadster chassis with a bolt-on brake kit specifically designed for our '37-'41 Ford style spindles and 9" Ford rear end. Each kit includes all necessary components: new rotors (available with 5-on-4.5" or 5-on-4.75" bolt pattern), remanufactured GM Metric calipers, caliper brackets, brake pads, bearings, seals and hardware. Rear kit bots on new-style Big Ford ends.
Complete the front and rear suspension assembly on your T roadster chassis with a bolt-on brake kit specifically designed for our '49-'54 Chevy style spindles and 9" Ford rear end. Each kit includes all necessary components: new rotors (available with 5-on-4.5" or 5-on-4.75" bolt pattern), remanufactured GM Metric calipers, caliper brackets, brake pads, bearings, seals and hardware. Rear kit bots on new-style Big Ford ends.
Our 1935-40 Ford frame assembly will replace that rusty original while retaining original mounting points. Just add our hub to hub Mustang II front end kit and rear suspension. Due to the many options, no motor mounts or rear suspension mounts are installed. Can be used as a 1935-40 Ford pick up frame if the two brackets on each side are removed. Our standard features include fabricated frame rails, Mustang II front crossmember, boxed frame, tubular center crossmember and transmission mount. Also included in this kit is the power brake ...
Looking for a little more interior room and a lower profile in your T roadster? Then try our Deluxe '27 T! The all-new Deluxe '27 frame features the same triangulated four-bar rear suspension as the Deluxe T, but with a longer wheelbase and extended rear frame section to accommodate Speedway's high-quality fiberglass '27 T roadster body. The body-and-frame combo can be used to build a hot rod with the same open engine bay and fenderless look of a T-bucket, but offers a lower seating position and a lot more legroom. ...
Triangulated 4-link rear suspension kit, including a Ford 9" rear end, specifically for the Speedway '32 Ford Boxed Truss frame 916-57050. This kit is a true bolt-in into our '32 Ford frame - no welding required. We suggest QA1 Adjustable rear coilovers 721-485 (at right) with 225 pound springs for this kit.
Triangulated 4-link rear suspension kit, including a Ford 9" rear end, specifically for the Speedway '34 Ford Boxed Truss frame 916-57085. This kit is a true bolt-in into our '34 Ford frame - no welding required. We suggest QA1 Adjustable rear coilovers 721-485 (at right) with 225 pound springs for this kit.
This parallel 4-bar kit is designed for our 1935-1940 Ford frame(916-57049),but it willalso work withaboxed original OEM frame. Rear brackets have 3 mounting holes for adjustable ride height. Adjustable bars have a 1" O.D. with urethane bushings and all necessary hardware. Plain finish, welding required.
For Model A Frame part #91657045. These 4-bar rear suspension kits include plain or polished 4-bars, rear axle brackets, lower coilover mounts and plain Panhard bar. Welding required.
These Deluxe Shockwave rear suspension kits have Shockwave air shocks and compressor. Includes panhard bar, two 32" radius rods with mounting brackets and hardware. Available in chrome or plain. Two ride heights to choose from.
The all new Deluxe T frame is engineered to deliver the ultimate ride and handling of any T-bucket chassis! An exclusive triangulated four-bar rear suspension with coilover shocks and urethane bushings provides unparalleled adjustability and traction control, plus better ride quality than any other T-bucket chassis on the market. It's paired with urethane-bushed four-bars supporting the spring-behind-axle front suspension. The Deluxe '23 T sets a new standard for the next generation of T-buckets!