High cornering forces can force the gear lube out of the center section and down the axle tube leaving the ring and pinion high and dry! This billet aluminum seal has three O-rings that seal it to the axle tube and two bonded, heavy duty, neoprene inner seals designed to compensate for any amount of axle shaft runout. Keeps gear oil in the center section. These seals will take up to an 1.5” diameter axle. Anodized billet aluminum A must for cambered rear ends For 9" Ford Grand National and ...
The great look of a quick change rearend at a fraction of the price! Contoured to fit an early Ford "banjo" axle housing. 916-47902 Instructions (PDF)
Get the look of a Champ quick change with this Jaguar differential cover. Cover includes a vent and fill hole. Measures 8-3/4" front to back.
One size fits all! Fits any inner axle tube with an I.D. between 2-1/2" and 2-3/4". This eliminates ordering the wrong seal and allows you to always have the correct seal on hand. Typical applications* include Ford 9”, Quick change type rears, and 12 bolt GM. All seals are supplied with general installation guidelines. Inner Axle Seal I.D. = 7/8" Axle sizes/Splines: 1-3/16” thru 1-1/2” / 28-31 * Applications are reference only. Seals may be used on any rear end that is within the part number’s dimensional range. Rears ...
Finally an all new V8 quick change that has steel side bells and tubes that accept modern axles. They are available in either plain finish or a polished center section that includes stainless steel fasteners. These rear ends are 56" from hub to hub and have both 5 on 4 1/2" and 5 on 4 3/4" bolt patterns. They accept the new style big Ford brakes with a 2 1/2" offset and the standard Spicer 1310 Chevy 3-1/4" u-joint. The 3.78 ring and pinion is mounted on a wedgelock differential ...
It's been a long time since you could buy a 100% brand new V-8 quick change rearend with the features this one showcases. Each of these rear assemblies includes new axles with 5 on 4-1/2" and 5 on 4-3/4" bolt patterns, 3.78:1 ring & pinion, Wedgelock differential, 1310 series yoke, and plain steel axle tubes. Accepts our part #91712 6-spline quick change gears. 56" wide hub-to-hub. Uses the big Ford bearing (3.150") and has a 2-1/2" axle offset. THIS ITEM SHIPS TRUCK FREIGHT
Screws into fill hole. For better installation, drill hole below fill hole. Ideal for big quick change rear cover, 1/8" NPT. You will have to drill and tap rear cover 92547004 to use this level checker.
Finally an all new V-8 quick change that has steel side bells and tubes that accept modern axles. They are available in either plain finish or a polished center section that includes stainless steel fasteners. These rear ends are 56" from hub to hub and have both 5 on 4 1/2" and 5 on 4 3/4" bolt patterns. They accept the new style big Ford brakes with a 2 1/2" offset and the standard Spicer 1310 Chevy 3-1/4" u-joint. The 3.78 ring and pinion is mounted on a wedgelock differential ...
Whether you're running a stock flattie and rearend or hopped-up overhead and quick change, you need to run a good gear lube. Remember that your rearend was designed fifty plus years ago and needs all the help it can get. The biggest improvement you can give it is a lubricant that will allow the gears to survive the highway speeds that cars see today. L.E. rear end lube is what we use in our 350 mph streamliner, that uses a V-8 quick change, without failure. The "red stuff" provides superior ...