No items in Shopping Cart
Here you get the hose, hose end fittings and fuel pump fitting if required. Choose from push-on steel or aluminum fittingswith blue hose, or aluminum fittings with stainless steel braided hose. AN8 hose only.
These 3/8" fuel line kits have a clean look and are easy to install. Choose with or without fuel filter. These fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution. The drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. The 325-8126 includes a barbed end for a push-on 5/16" or 3/8" rubber fuel line. The 325-8131 includes an aluminum fuel filter with a 40 micron filter element and -6 AN female inlet will accept an ...
Black push-on hose available in AN6, 8, 10 and 12. Ideal for fuel line applications only -NOT suited for oil or water use exceeding temperatures of 200 F.
Direct replacements for OEM fuel rail and return line fittings in late-model EFI pressure side applicationFeature Russell's exclusive SAE quick disconnect threaded aluminum retaining cap for ease of installation and positive engagement under high pressure37 sealing angle guarantees a positive seal at maximum operating pressures Black or Blue anodized finish
The main issue when dealing with aluminum tubing (or any aluminum for that matter) is that it "work hardens" when it flexes, which can lead to cracks. It is important that the hard line is isolated from vibration and movement.
Ensures adequate fuel pressure to carburetor and helps eliminate fuel starvation problems. Fuel pressure is regulated after carburetor has been supplied and not before. Must use return fuel line to take full advantage of benefits. Features AN8 inlet and two AN8 outlets. Threaded 3/4" NPT (plugged) on back that can be used for a return line. Also has 1/8" NPT outlet for fuel pressure gauge, fittings sold separately.
This fuel line is intended to connect two Edelbrock (or Carter) four-barrel carbs on a low-rise 2x4 intake. The inlet fitting thread is 3/8" NPT female, and there is a 1/8" NPT hole that can be used for a fuel pressure gauge. The outlets on this line can be as close together as 6-1/2" and as far apart as 8-1/4". All of the line is anodized blue, except for the central piece of braided stainless steel hose.
Speedway Red See-Through Fuel Line is the perfect old-time accent to your multi-carb street rod! This specially-formulated, flexible tubing has a 3/8" inside diameter and comes in 6 foot lengths. You can easily trim it to your needs. Works with normal slip-on hose barb fittings and clamps.
Aeroquip FC300 spec hose to be used as the fuel or power steering line. Hose only works with listed fittings (not included). Easily assembles with a bench vise and/or wrenches. Ends are reusable. Hose sold by foot.The AN6 high pressure hose has an ID of 0.31" and an OD of 0.67". The maximum operating pressure is 2250 psi and the minimum bend radius is 4". Its applications include: power steering lines, hydraulics, air, gasoline, fuel, lubricating oils, over the wall air tools, and DOT-approved air brakes. This high pressure hose ...
Aeroquip FC 300 spec hose to be used as the fuel or power steering line. Choose AN 10 and fittings required.
2 brass fittings, 14" pipe thread for 38" ID hose, 2 stainless hose clamps per set.
This braided pressure gauge line kit makes it a snap to hook up your pressure gauge. Can be used with oil, water, fuel or air. Includes AN 4 braided line, AN4 to 1/8" NPT male and AN4 to 1/8" NPT female. Choose from lengths of 25", 36" or 48".
Includes one chrome 20" line and one chrome 14" line with male inverted flare fittings. Ideal between mechanical fuel pump and carburetor. 5/16" diameter. Bendable.
Available for 4150 Holleys with 7/8"-20 inlets or 9/16"-24 inlets for Demon carbs. Includes 1/8" NPT fuel pressure port.
Most modern engines have a hi-pressure fuel pump located in the gas tank. If you are transplanting one of these engines into your hot rod, what are you going to do for a fuel pump? This MSD pump can be mounted on the frame and can put out up to 43 gph at 40 psi or 39 gph at 80 psi.
These all-new (not rebuilt) mechanical fuel pumps from Holley have a 7-1/2 psi shut-off pressure and deliver 80 GPH. The adjustable lower housing permits fuel ports (1/4" NPT) to be rotated for best fuel line access.
These slick inlet fittings have two AN6 ports built in to run your returns to. They screw into the AN8 inlet side of your fuel pump and allow either an AN10 or AN12 line to be used.
Edelbrock Victor Series billet aluminum mechanical fuel pumps are for high performance racing applications. The 5/8"-18 inlet and outlet come with -8AN fittings installed to provide increased flow over street fuel pumps, and the base can be rotated to allow for various fuel line configurations. These billet aluminum pumps produce 8.5-9 psi and require a pressure regulator.
We offer longer fuel lines to compensate for extra length between fuel bowls.
61764850Overall Length1.750" (1 3/4")Overall Diameter0.853"ColorBlueMaterial TypeAluminumFinishAnodizedSold in QuantityEachNotesSnaps into GM fuel rail.
61764853Fitting End ASnaps into 3/8" fuel lineFitting End BAN-6Material TypeAluminumFinishAnodizedColorBlackSold in QuantityEach
61764863Sold in QuantityEachNotesBlack Anodized, Snaps into a GM 5/16" fuel line to a AN6