No items in Shopping Cart
Die stamped stainless steel 1928-29 open car windshield posts. Polished.1928-29 Chopped: These posts are reproductions of the original design, only 2" shorter. They include 2 mounting holes per post. Length from end to windshield pivot stud hole is approximately 14-1/2". From end to end is approximately 16-3/4".
These polished stainless steel windshield posts will give your roadster a smooth, clean look. Plus, installingthis chopped windshield is a snap. Comes with post caps for a smooth, unique look.
Die stamped stainless steel 1928-29 open car windshield posts. Polished.
Clean up the bed of your pickup with these smooth and highly polished stainless steel strips. Which use sliding T-bolt fasteners (sold separately) to eliminate the stock-style carriage bolts. Each universal set comes with seven strips that are 82" long.
Screen style oil windage tray for S/B Chevy engines using a stock style pan with rear sump. Ready to install.Fits 2 or 4 bolt main blocks.
Stock style glass caps fit all Model T windshields.
Stainless Steel Pedal Padwith rubber insert. Universal. 1/2" fine threadfor attaching stud on the back.
Polished stainless steel headlights feature a 12 volt H5 quartz halogen bulb (high & low beams) behind original stylelens with mounting stud. Light is 10" diameter.
Our universal fit Deitz-type 7" headlights feature stainless steel housings and a 12 volt sealed beam bulb with bothhigh & low beams. "Drilled" mounting stud measures 1/2"-13. The pre-wired plug has 3 wires with 6" leads.
These stainless steel upper front shock mounts measure 4" from the top bolt hole to the centerline of the stud. Mounting bolts are spaced at 2-5/16" on center.Shocks bushing and stainless steel hardware is included.
These stainless steel headlight mounts are the perfect touch for your fenderless car.Measures 4-3/4" from mounting surface to the top of the headlight cup.
Replacement 10" stainless filter elements to fit our 2" filter bodies. 45 micron. Designed for race car use only. Compatible with methanol and gasoline. NOT compatible with ethanol (E85).
Stainless steel filter elements to fit our 2" x 6" aluminum filter bodies. Designed for race car use only.Compatible with both methanol and gasoline. NOT compatible with ethanol (E85).
For production chassis. Exits under car on Pinto or Mustang IIHigh velocity 1-5/8" to 1-3/4" stepped primary with 3" collectorIncludes gaskets and header bolts
This stainless steel fuel fill can be flush mounted and includes a special opening key. Simple three hole mounting makes installation a snap.
A beautiful polished stainless steel clevis ideal for your hot rods' suspension! The shank features 5/8" RH fine threads. Has a3/8" wide slot and 3/8" diameter hole.
91002929Center Hole to End of Shank3.250Degree of Taper7 degreeShank Diameter0.780"Shank Length2.500" (2 1/2")Thread Pitch11/16"-18Thread Length2.000"Material TypeStainless SteelFinishPolishedSold in QuantityEachNotesFit closer to the tapered hole in comparison to our plain tie rod 91002909 as they are .150" shorter.
91002939Overall Length4.000"Center Hole to End of Shank3Stud Length0.750" (3/4")Stud Diameter0.500" (1/2")ThreadsRH FemaleThread Pitch11/16"-18Thread Length2.000"Material TypeStainless SteelFinishPolishedSold in QuantityEachNotesFit closer to tapered hole compared to our 91002919 which is.150" shorter. 1-1/8" from center of threaded shaft to the bottom of the taper.
Upper posts available for standard or deluxe in polished stainless steel.
These short style Model T windshield posts are laid back 30 for a more racy look. They are made of Stainless Steel and include mounting bosses on back side to permit a smooth, clean installation. Fits our 1923-25 T-bucket bodies but can be used on others with a little fitting.