Polished Block Manifold

Tru-Ram® Exhaust Manifolds allow you to enjoy the nostalgic look of factory BBC style manifolds, without sacrificing any performance. Investment cast from durable stainless steel material, these exhaust manifolds will be a low maitenance, high-performance addition to any Big Block Chevy-powered vehicle. Features a fully polished, show-quality finish.  High-performance tubular design Smooth internal transitions perform like shorty headers Tightest fit to block available Added clearance for steering shaft Round 1-7/8" primary tubes with large 3" collector outlet Standard 3 bolt collector ...

No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold. These 360° manifolds feature dual distributor hold downs for Chevy four corner water outlets and line of sight port configuration. They also have extended port dividers thermostat recess and an accessory bracket boss and tapped hole.There is an air gap under the front water crossover for extra cooling and an extra tapped water port. These manifolds have permanent mold castings for accurate port placement tighter grain ...

If you already have a blower and drive we offer just the intake. Adapt 6-71 superchargers toSmall BlockChevy. Cast aluminum they feature an integral pop-off valve and utilize stock-type thermostats and housings.

The Professional Products Typhoon manifold for 351W Fords is the ultimate performance dual plane manifold. Its long runner 180° design provides the best of both worlds - good top end power without sacrificing bottom end torque. Accepts square flange carbs. RPM range is 1500-6500. Available plain, show polished or chrome. This manifold has features not found in manifolds: Includes a rear water crossover passage Provides balanced cylinder head temperatures Overall cooler running engine Cast-in bosses for possible addition of direct port nitrous injection  910-11235 Instructions  (PDF)  ...

The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds, not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally, each Power+Plus Manifold is 100% pressure ...

The Professional Products Cyclone manifold is the ideal street manifold for street rods or engine swaps using the popular1996 and later Vortec (L31) cast iron heads. Manifold includes adapter to use a square bore carb and features dual distributor hold downs. Also includes two pipe tapped rear water ports. Available for plain or polished.  Fits Vortec blocks or 1995 & earlier blocks with Vortec heads. RPM range is idle to 5500. Chevy Vortec Manifold Installation Instructions  (PDF) 

If you are running a little more motor then this is the intake for you! The Professional ProductsTyphoon manifold is a high performance dual plane 180° street manifold designed to be used with Holley Carter AFB or Edelbrock squareflange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters.RPM range is 1500-6500Available plain show polished or chromePower comparable to single plane manifolds yet retains throttle response/driveability of a dual planeCast-in nitrous bossesWater outlets at all four cornersDual distributor hold-downsProvisions to add an oil fill ...

The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally each Power+Plus Manifold is 100% pressure ...

No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold. These 360° manifolds feature dual distributor hold downs for Chevy four corner water outlets and line of sight port configuration. They also have extended port dividers thermostat recess and an accessory bracket boss and tapped hole. There is an air gap under the front water crossover for extra cooling and an extra tapped water port. These manifolds have permanent mold castings for accurate port placement tighter ...

TheProfessional ProductsTyphoon manifold for 260-289-302 small block Ford V8s is a dual plane 180° high-rise design that delivers outstanding street or race performance acrossa widepower band while retaining good throttle response at any speed.This dual plane intake accepts square flange carbs.RPM range is 1500-6500Available plain show polished or chromeHas (1)1/2" & (3) 3/8" NPT water ports one at each cornerCast-innitrous bossesRecommended carburetor is any square bore 600 cfmto 750 cfm910-11275 Instructions(PDF)

No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold. These 360° manifolds feature dual distributor hold downs for Chevy four corner water outlets and line of sight port configuration. They also have extended port dividers thermostat recess and an accessory bracket boss and tapped hole.There is an air gap under the front water crossover for extra cooling and an extra tapped water port. These manifolds have permanent mold castings for accurate port placement tighter grain ...

The Professional Products Typhoon manifold for 260-289-302 small block Ford V8s is a dual plane 180° high-rise design that delivers outstanding street or race performance across a wide power band, while retaining good throttle response at any speed. This dual plane intake accepts square flange carbs. RPM range is 1500-6500 Available plain, show polished or chrome Has (1) 1/2" & (3) 3/8" NPT water ports, one at each corner Cast-in nitrous bosses Recommended carburetor is any square bore 600 cfm to 750 cfm 910-11275 Instructions  (PDF) 

Tru-Ram® Exhaust Manifolds allow you toenjoy the look offactoryLS style manifolds without the hassle of dealing withunsightly rust and corrosion. Investment cast from durable stainless steel material these exhaust manifolds willbe a low maitenance high-performanceaddition to any LS-powered vehicle. Features a fully polished show qualityfinish. Tucked-in shape hugs block contourSmooth internal transitions perform like shorty headersCollector angle is optimized for maximum frame rail clearance on any applicationRound 1-3/4" primary tubesLarge 3" collector outletStandard 3 bolt collector ...

If you already have a blower and drive, we offer just the intake. Adapt 6-71 superchargers to Small Block Chevy. Cast aluminum, they feature an integral pop-off valve and utilize stock-type thermostats and housings.

If you are running a little more motor, then this is the intake for you! The Professional Products Typhoon manifold is a high performance dual plane, 180° street manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters. RPM range is 1500-6500 Available plain, show polished or chrome Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane Cast-in nitrous bosses Water outlets at all four corners Dual distributor hold-downs Provisions to ...

If you already have a blower and drive, we offer just the intake. Adapt 6-71/8-71 superchargers to Big Block Chevy. Cast aluminum, they feature an integral pop-off valve and utilize stock-type thermostats and housings. Rear Mounted Pop Off Plate (Included) Standard deck only Boost Gauge port  

Tru-Ram® Exhaust Manifolds allow you toenjoy the nostalgic look offactory BBC style manifolds without sacrificing any performance. Investment cast from durable stainless steel material these exhaust manifolds willbe a low maitenance high-performanceaddition to any Big Block Chevy-powered vehicle. Features a fully polished show-qualityfinish. High-performance tubular designSmooth internal transitions perform like shorty headersTightest fit to block availableAdded clearance for steering shaftRound 1-7/8" primary tubes with large 3" collector outletStandard 3 bolt collector patternIncludes ...

If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower. RPM range is 1500-6500 Available plain or show polished Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane Cast-in nitrous ...