(0)
Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Large Image
CLOSE [X]

Chevy Weld-In Motor Mounts

Price:$79.99
S/B & B/B CHEVY WELD-IN MOTOR MOUNTS
Price:
$79.99
PR
In Stock
Item #:
91018040
 
(7 Ratings)
Click image to enlarge Click image to enlarge
  • Chevy Weld-In Motor Mounts
  • Chevy Weld-In Motor Mounts
  • Chevy Weld-In Motor Mounts
  • Chevy Weld-In Motor Mounts
No video at this time.
 
  • 91018040
    Material Type
    Steel
    Sold in Quantity
    Pair
    Notes
    20.375" bushing eye-to-eye when bolted to a Chevy block (each mount is 3-1/16" long to center of bushing). Three engine mount holes are 3-1/2" center-to-center. Frame brackets are 3-7/8" long.

More often than not, we are trying to put an engine in something that no one has built bolt-in mounts for. If that's your story, we have just the deal for you! This S/B Chevy and B/B Chevy motor mount has a poly bushing in it giving you a vibration free installation.

Welding and fitting required.

  1. Older versions of this mount will use replacement bushing 917-2253B. Mounts produced starting early in 2005 will use bushing 917-2255B.
Reviews for Item #: 91018040
REVIEWED BY 7 CUSTOMERS
Sort by:
Displaying Reviews 1-5 of 7
Next »
Processing
 

very nice mount set up

By dragrcr50 woodard racing & hot rods from mustang oklahoma on 3/9/2010
Pros:
Look good easy to use an
Cons:
Ears too short
Best Uses:
Gasser builds
Bottom Line: Yes, I would recommend this to a friend

we use them when we clip the front of the gassers we build for a clean mount set up . they fit just right and look great. very strong and solid. however the ears provided are a couple of inches short for our tri five clips we build, we have to fab new ears for them..

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

great product for the price!!!!!!!!

By gostranger from phelps, New York on 1/25/2010
Pros:
Cost was low quality was
Best Uses:
I used mine on a 66 c10, Ls vortec engine swap
Bottom Line: Yes, I would recommend this to a friend

used on my 66 c10 needed to change the position of the Ls vortec swap used these to mount off the crossmember instead of off the frame worked perfectly there were higher costing solutions out there but none better!!!!

Service & Delivery comments:

superfast delivery great place to deal with!!!!

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

doesnt fit 23 t

By randy from oklahoma on 11/9/2010
Bottom Line: No, I would not recommend this to a friend

Theses are built good but supplied brackets will not fit a 23 t bucket.would be great with cars with alittle wider frame.

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

SBC swapped into a 54 Chry New Yorker!

By Jxnslotcar from Jackson,Michigan on 12/18/2010
Pros:
Ease of Use, Fitment
Cons:
none
Best Uses:
Engine swaps, Tight spaces
Bottom Line: Yes, I would recommend this to a friend

Had to cut down frame brackets to fit-but was easy to do. Welded nice and is strong. I am swapping a SBC into a 1954 Chrysler New Yorker which is not an easy task to say the least. I am doing it while keeping stock steering and suspension. Will buy these again!

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

a great fix for bad homemade mounts

By Mike from Phelan, Ca. on 2/13/2011
Pros:
Durable
Car & Truck:
Auto Enthusiast, Truck Enthusiast
Best Uses:
Everyday Driving, Performance Driving, Racing, Replacement, Restoration
Bottom Line: Yes, I would recommend this to a friend

stuck a 283 in a '53 Willys wagon and needed these to clear the front differential and driveshaft. Worked great.

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

Displaying Reviews 1-5 of 7
Next »
 

Questions and Answers for Item #: 91018040

Get your questions answered by the community. Ask or answer questions below.

3 Questions | 3 Answers
Displaying Questions 1-3 of 3
Processing

Q:

I need to know the measurements of where the mouny bolts to engine to the tip of the very end (where the bushing sets in) and also the dimensions of the plates

Asked on 2/19/2011 12:45:07 PM by Cody from Derby,ks

Answers (1) Know the answer? Answer this question

Q:

Do you sell replacement bushings for these?

Asked on 7/9/2011 3:20:43 PM by Cody from Derby,ks

Answers (1) Know the answer? Answer this question

Q:

Would these motor mounts be the right ones for a SBC 350 and a Heidts Mustang II crossmember in 49 Chevy truck? If not, which mounts would work best. Thank you very much.

Asked on 2/9/2012 10:31:31 AM by Cody from Derby,ks

Answers (1) Know the answer? Answer this question
Displaying Questions 1-3 of 3

Do you have a question about this product?

Email this page
Close [x]
You can send this product by email to a friend!
Enter the required information in the spaces provided below. They will receive an Email with the picture of this product and a link back to our site.
Your Name:
Your Email:
Friends Name:
Friends Email:
Print Page