Nova Rear Axle

Speedway Motors now offers you a 9" Ford street 3rd member for your street rod. We reclaim genuine Ford 9" housings, clean, inspect and install all new components. All bearings, seals, 1310 series yoke and ring & pinion are new! These Ford 9" 3rd member assemblies feature new Pro Gears ring & pinion, choice of 3.50, 3.70, 3.89, 4.11 or 4.56, Currie 9-Plus limited slip differential, 28 or 31 spline. Shipped in handy plastic carrying case. Assembled by professionals.   Currie Differential Tech Bulletin (PDF)   910-48345 Instructions (PDF)

Our 3" dropped axle for your classic '47-'54 Chevy half-ton pick-up will get the front end down where you want it. The center portion of the axle is made of 2" DOM tubing while the ends are CNC milled for solid steel. These axles give you 3" of drop. The Chevy axles require the steering arm to be modified to accept rod ends or tie rods. U-bolts sold separately. King pin to king pin centers = 50.5" 6" drop measured from spring pad to spindle boss center Axle accepts a ...

These 27-spline axles have RH thread on one end and LH on the other. Use with our bearing sleeves.

Currie axle made to work in the 60" centered Speedway Motors Ford 9" rear housing (910-46115). Our matched axle to complete the set (910-46116). 28-3/8 inches long.

Currie axle made to work in the 56" centered Speedway Motors Ford 9" rear housing (910-46110). Our matched axle to complete the set (910-46108). 26-3/8 inches long. Drilled for 5 on 4 1/2 and 5 on 4 3/4 bolt pattern.

These 27-spline axles have RH thread on one end and LH on the other. Use with our bearing sleeves. Note:   This axle will not work if using a panhard bar and mounting the brake on the right side of the axle as there are not enough splines. 

Rear end oiling can mounts flush on rear deck.  Aluminum, 24 oz. capacity.  7 1/2" tall, 3" diameter. Mounting flange is 8 1/2" diameter. AN 10 outlet.

V-Front/Tooth Rear Axle Only Select the link below to view all parts for your pedal car. Please refer to application tab to double check part fitment. Parts shown in the exploded view but not listed are currently not available. Sorry! Exploded Parts Diagram for Murray V-Front/Tooth Grille(Link)

AMF Rear Axle with Pedal Strap BearingSelect the proper link below to view all parts for your pedal car. Please refer to application tab to double check part fitment. Parts shown in the exploded view but not listed are currently not available. Sorry! Exploded Parts View for AMF Generic (Link)Exploded Parts View of AMF Mustang (Link)

Garton Mark V Rear Axle with Saddle Select the link below to view all parts for your pedal car. Please refer to application tab to double check part fitment. Parts shown in the exploded view but not listed are currently not available. Sorry! Exploded Parts View for Garton Mark V (Link)

Winters Grand National full floating Ford 9 inch rear end housing.

Winters Grand National replacement full floating Ford 9 inch rear end housing. Part # 655-4800 features two 30" tubes and the pinion is centered. Part # 655-4803 features  has a driver side tube at 31-1/2" in length and pass. side is 30-1/2" in length.  Pinion is offset 1/2" to RH side.

These 27-spline axles have RH thread on one end and LH on the other. Use with our bearing sleeves.

Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 58" from hub-to-hub. You will need one 29-5/8" long axle and one 27-3/8" long axle.  Includes 8 T-bolts for the axle bearing retainer plates and 10 studs for the 3rd member. Third member sold separately.  

Currie axle made to work in the 58" centered Speedway Motors Ford 9" rear housing (910-46105). Our matched axle to complete the set (91046106). 27-3/8 inches long.

Inboard brake compatible Bleeder groove Increased rigidity, superior material, and additional spline length make this axle the most versatile option available. 31 Spline. Note: Requires use of 31 spline midget birdcage set.

Now you can have the strength and serviceability that Ford drivers have enjoyed for years underneath your GM vehicle. Currie Crate Rearends are built using the stock overall width, pinion offest, and mounting points of your original rear axle housing, making it a 100% bolt-in upgrade. All new 9-Plus heavy duty housing Heavy duty reproductions of the GM multi leaf spring pads installed 31 spline performance axle shafts 60" width Torino-style late model large bearing housing ends Third member studs installed Axles drilled for stock 5 on 4-3/4" wheel bolt ...

Now you can have the strength and serviceability that Ford drivers have enjoyed for years underneath your GM vehicle. Currie Crate Rearends are built using the stock overall width, pinion offest, and mounting points of your original rear axle housing, making it a 100% bolt-in upgrade. All new 9-Plus heavy duty housing Heavy duty reproductions of the GM mono leaf spring pads installed 31 spline performance axle shafts 60-1/4" width Torino-style late model large bearing housing ends Third member studs installed Axles drilled for stock 5 on 4-3/4" wheel bolt ...