21 super bright LEDs Complete with polycarbonate lens Die cast chrome plated bezel Epoxy coated, fully sealed electronics 1157 style plug Operates on 7.7 - 14.0 VDC The bezel is 5-3/16" long by 1-7/8" tall by .550" thick
This 12-volt LED tail light has a stop/turn/tail and can be mounted on a flat surface. Measures 4-1/2" long x 2-9/16" tall. Includes a rubber mounting gasket. Requires 10-32 mounting bolts (not included). LED Tail Light Installation Instructions (PDF)
Face it, it's hard to see those tail and brake lights on older cars. Now is the time to change out those broken or faded lights for new LED versions. 68 Super Bright LEDs, complete with Polycarbonate lens Epoxy coated, fully sealed electronics, 1157 plug Solid state circuit board designed for 7.7 - 14.0 VDC
These powerful LED tail lights are a direct replacement for 1940 Chevy passenger cars. Features 14 LED's per tail light, a pressure cast bezel, a molded-in reflector for lights-off safety, and stainless steel hardware.
This is the perfect finishing touch for your 1940-1941 Willys coupe project. These beautiful tail lights have a cast bezel that is chrome plated and ultra bright LED's let everyone know if you are stopping. 1940-1941 Willys Tail Light Installation Instructions (pdf)
These tail lights are flat on the back for easy mounting to most any surface, as each only needs 3 holes (1/4" Diameter) drilled in the mount surface. Wired for tail light, stoplight, and turn signals. 12V. Includes base gasket.
Face it, it's hard to see those tail and brake lights on older Mustangs. Now is the time to change out those broken or faded lights for new LED versions. 68 Super Bright LEDS Polycarbonate Lens Epoxy Coated, Fully Sealed Electronics, 1157 Plug Solid State Circuit Boards Designed for 7.7 - 14.0 VDC
These 12 volt LED tail lights fit most 1940-1953 Chevrolet trucks that use two staggered bolts on the rear for mounting. A total of 45 super bright red LED's mount in a stainless steel housing. Polycarbonate Lens The left drivers side taillight has a license plate 6 LED light. The right passenger side taillight does not have a license plate light. Note: A LED flasher is only required when all the lights on the vehicle are LED. 1940-1953 Chevy Truck Tail Light Installation Instructions (pdf)
Face it, it's hard to see those tail lights on older cars. Now is the time to change out those broken or faded tail lights for new LED versions. 98 Super Bright LEDS Circuit Board Only to Retrofit Existing Lens Epoxy Coate Fully Sealed Electronics 1157 Plug Solid State Circuit Boards designed for 7.7 - 14.0 VDC
Each of these complete 1938-1939 Ford Mini Zephyr LED Signature Series tail lights are optimized for visibility and proper fit on the car. All of our tail lights include a pressure cast bezel, a molded-in reflector for lights-off safety, and stainless steel hardware. Plus, with RapidFire technology, the brake lights are pulsed rapidly three times within the first 1/2 second of pressing the brake pedal followed by constant ON. This cycle is repeated every time the brake pedal is pressed. We think this is a valuable safety feature, but can be overridden ...
Direct replacement LED tail light assemblies for your 1955-1959 Chevy Pickup Truck. Sold individually.Stainless Steel Housing41 Super Bright Red LEDsPolycarbonate LensEpoxy Coated Fully Sealed Electronics
Chrome rim with powerful red LED tail lights. An excellent replacement for your 1950 Pontiac or custom application. 41 super bright red LEDsPolished stainless steel housingEpoxy coated fully sealed electronicsSolid state circuit board for 12V systemsTaillight-to-body mount gasket NOT included.
Face it it's hard to see those tail lights on older cars. Now is the time to change out those broken or faded tail lights for new LED versions. 40 Super Bright LEDSPolycarbonate LensEpoxy Coated Fully Sealed Electronics 1157 PlugSolid State Circuit Boards Designed for 7.7 - 14.0 VDC
These powerful LED tail lights are a direct replacement for 1940 Chevy passenger cars. Features 14 LED's per tail light a pressure cast bezel a molded-in reflector for lights-off safety and stainless steel hardware.
Complete tail light assembly with very bright and visible LED's for the stop, tail, and turn signal functions. LED's feature a wide viewing angle of 100 degrees as well as cool operation and long life. This led taillight is designed to bolt into a 1940 Ford fender in place of the original taillight. Kit Contents: (2) LED complete taillamp assemblies, (4) solderless connectors, (2) LED to car electrical harness, (2) custom molded taillamp to body seal, installation instructions. Bezel re-shaped to fit tightly to fender External screw hole eliminated for ...
These LED tail lights are among the best you will find for your old Plymouth. They feature chrome plated die-cast metal housings with stainless steel mounting studs, nuts and washers. They are a direct replacement with the benefits of LED brightness (14 LED's per light). Simple, clear wiring directions (12 volt only) and includes wiring and even taillight-to-body gaskets. Includes RapidFire brake lights function Brake lights are pulsed rapidly three times within the first 1/2 second of pressing the brake pedal followed by constant ON Cycle is repeated every time the ...
Authentic reproduction of the 1937 Ford passenger car tail light housing complete with modern LED lens. Black painted housing. Choose left or right side. 17 Super Bright Red LEDsPolycarbonate LensDrivers side (Left) includes a 6 LED White License Plate LightSolid state circuit boards designed for 7.7 - 14.0 VDC
Polished stainless steel housing with powerful red LED tail lights. An excellent replacement or addition to your 1932 Ford Deuce. Choose right or left. 17 super bright red LED's4" diameter3" deepDrivers side (Left side) includes a 4 LED white license light Polished stainless steel housingEpoxy coated fully sealed electronicsSolid state circuit board for 12V systems1932 Ford LED Tail Light Installation Instructions(PDF)
These 12 volt LED tail lights fit most 1940-1953 Chevrolet trucks that use two staggered bolts on the rear for mounting. A total of 45 super bright red LED's mount in a stainless steel housing. Polycarbonate LensThe left drivers side taillight has a license plate 6 LED light. The right passenger side taillight does not have a license plate light.Note: A LED flasher is only required when all the lights on the vehicle are LED.1940-1953 Chevy Truck Tail Light Installation Instructions (pdf)
Each ofthese complete 1938-1939 Ford Mini Zephyr LED Signature Series tail lights are optimized for visibility and proper fiton the car. All of our tail lights include a pressure cast bezel a molded-in reflector for lights-off safety and stainless steel hardware.Plus with RapidFire technology the brake lights are pulsed rapidly three times within the first 1/2 second of pressing the brake pedal followed by constant ON. This cycle is repeated every time the brake pedal is pressed. We think this is a valuable safety feature but can be overridden at ...
These LED tail lights are among the best you will find for your old Plymouth. They feature chrome plated die-cast metal housings with stainless steel mounting studs nuts and washers. They are a direct replacement with the benefits of LED brightness (14 LED's per light).Simple clear wiring directions (12 volt only) and includes wiring and even taillight-to-body gaskets.Includes RapidFire brake lights functionBrake lights are pulsed rapidly three times within the first 1/2 second of pressing the brake pedal followed by constant ONCycle is repeated every time the brake pedal is ...
Convert any three LED tail lights to sequential operation Also upgrades Speedway Motors brand 1969 Camaro and 1967-'69 Mustang LED tail lights to three sequence Three segment sequence with "all-at-once" brake light Kit includes two modules, wires, connectors and instructions Sequential LED Tail Light Wiring Instructions (PDF)