All brackets are for 3" rear axle application. Low Rear Axle Bracket Mount radius rods lower than rear axle. 3/8" steel. 5-3/4" long. 3/8" holes.
All brackets are for 3" rear axle application. Heavy Duty Rear Axle Bracket 3" rear axle housing. 3/8" steel. 3/8" holes. 5-3/4" long.
"Short" rear axle bracket designed for use with Speedway rear radius rods. Fits 3" diameter rear axle tube3/8" thick steel3/8" diameter holes
"Long" rear axle bracket for use with custom radius rod rear suspensions. Fits 3" diameter rear axle tube3/8" thick steel3/8" diameter holes
All brackets are for 3" rear axle application.Heavy Duty Rear Axle Bracket3" rear axle housing. 3/8" steel. 3/8" holes.5-3/4" long.
All brackets are for 3" rear axle application.Low Rear Axle BracketMount radius rods lower than rear axle. 3/8" steel. 5-3/4" long. 3/8" holes.
License plate brackets attach to tube axles spreader bars etc. with a 2" O.D. This license tag bracket is available inplain or polished aluminum finishes.
License plate brackets attach to tube axles spreader bars etc.with a 1-3/4" O.D. This license tag bracket is available inplain or polished aluminum finishes.
Bracket fastens on rear axle and mounts coil-overs so that axle wrap tends to load or unload tires closest to clamps. For 3" axle tubes.The drop on this is 5” that is a measurement from the center of axle housing to the bottom of the shock mount. The shock mount is 1/2” for a standard racing shock eye lit size. The clamp width is 1-3/4”.
Weld these brackets to your 9" Ford housing and install it in your 1978-1988 GM Metric chassis. Includes upper and lower control arm mounts and weld-on caliper brackets for use with Metric calipers. Welding is required. Designed for 3-1/2" axle tubes but can be fit to 3" tubes. This kit isNOT IMCA Hobby Stock legal but is IMCA Stock Car approved.
Bracket fastens on rear axle and mounts coil-overs so that axle wrap tends to load or unload tires closest to clamps. For 3" axle tubes. The drop on this is 7”, that is a measurement from the center of axle housing to the bottom of the shock mount. The shock mount is 1/2” for a standard racing shock eye lit size. The clamp width is 1-3/4”.
Bracket fastens on rear axle and mounts coil-overs so that axle wrap tends to load or unload tires closest to clamps. For 3" axle tubes. The drop on this is 5”, that is a measurement from the center of axle housing to the bottom of the shock mount. The shock mount is 1/2” for a standard racing shock eye lit size. The clamp width is 1-3/4”.
AFCO clamp-on rear disc brake caliper bracket for 3 inch diameter axle tube. For smaller GM metric calipers. Stop-bolt recommended and included with bracket 106-40121C Instructions (PDF)
This steel Panhard bar bracket is a single mount, clamp-on style Panhard bracket. Fits 3" axle tubes.
AFCO weld-on brackets for GM single-piston iron calipers. Fits 3" axle tubes. This bracket is 7-1/16" center to center.
AFCO weld-on brackets for GM single-piston iron calipers. Fits 3" axle tubes.
AFCO clamp-on rear disc brake caliper bracket for3 inch diameter axle tube. For smaller GM metric calipers. Stop-bolt recommended and included with bracket106-40121C Instructions (PDF)
You can weld these brackets to your 9" Ford housing and install it in your 1978-88 GM Metric chassis. Includes upper and lower control arm mounts. Welding required. Designed for 3-1/2" axle tubes but can be fit to 3" tubes.
You can weld these brackets to your 9" Ford housing and install it in your GM Metric chassis. Includes upper and lower control arm mounts. Welding required. Designed for 3-1/2" axle tubes but can be fit to 3" tubes. ThisDeluxe rear end bracket set features multiple holes (5) for mounting the lower control arms. Alsoincluded is a pair of weld-on brackets for mounting the Metric brake calipers. The lower mounts in this kit have only one shock mount position. This kit isNOT IMCA Hobby Stock legal but is IMCA Stock ...
Fits 3.0" axle tube and F88i-style calipers. Used for swing arm birdcages.