No items in Shopping Cart
Mounts 1969-1977 GM mid-size car front caliper to any 3" tube rear end using 11-3/4" diameter rotors. Fully machined steelwith punched lightening holes. Measures approximately 7" between mounting holes.
US Brake weld-on brackets for GM single-piston iron calipers. Fits 3" axle tubes.
Mounts 1978-1988 GM front caliper to any 3" tube rear end using 11-3/4" diameter rotors. Fully machined steelwith punched lightening holes. Measures approximately 5-1/2" between mounting holes.
These bracketsare used to mount a GM "metric" calipers to 1974-1980 Pinto/Mustang II spindles for use with what is basically a "Granada" 10-1/2" brake rotor. Steel, bolt-on design mounts the caliper on the rear side of the left front wheel.
These bracketsare used to mount a GM "metric" calipers to 1974-1980 Pinto/Mustang II spindles for use with what is basically a "Granada" 10-1/2" brake rotor. Steel, bolt-on design mounts the caliper on the rear side of the right front wheel.
If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This complete kit includes two bolt-on caliper brackets, two 11-1/4" vented rotors, two GM metric style calipers, brake pads and hardware.
If you don't want to spend and arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes two bolt-on caliper brackets, two 11-5/8" vented rotors, two GM metric style calipers, brake pads and hardware.
If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This complete kit includes two bolt-on caliper brackets, two 11-1/4" vented rotors, two GMemergency brakestyle calipers, brake pads and hardware.
If you don't want to spend and arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes two bolt-on caliper brackets, two 11-5/8" vented rotors, two GMemergency brakecalipers, brake pads and hardware.
If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM metric style calipers, brake pads and hardware.
If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GMemergency brakecalipers, brake pads and hardware.
Aluminum brake bracket fits standard Eagle and Maxim birdcages. For Either a Right Rear or Left Rear braking system.
For 3.25 mount caliper and 10" rotor. Steel.
Looking for a low cost way to add rear disc brakes to your Ford 8.8" or 9" equipped hot rod, without searching the junk yards? Look no further. This Ford Racing rear disc brake kit includes OE quality single-piston calipers, 11.8" vented rotors, E-coated caliper mounting bracket, and all mounting components. Plus, the E-coated backing plate features an integral parking brake for a convenient install.
Save weight and increase braking with this scalloped rear brake kit. The .810" x 10.4" scalloped Chromoly rotor is ceramic coated for durability and performance and is mated to a billet caliper. Includes pads, bracket, clamp and hardware.
Caliper bracket slides over 3" axle tube and clamps on. Must be tack welded to keep from rotating.
These caliper brackets mount flat andmustbe welded onto your 3" diameter axle tube. Designed to mount a1978-1988 GM metric car front caliperforuse withan 11.75" diameter rotor. Brackets are 5/16" thick.
Allows you to bolt '78 an Up GM Metric disc brakes on Ford 9" rearend. Hardware sold separately.Includes:2 Caliper brackets2 Adapter plates2 Spacer plates8 5/16" spacers8 1/8" spacers
Weld these brackets to your 9" Ford housing and install it in your 1978-1988 GM Metric chassis. Includes upper and lower control arm mounts, and weld-on caliper brackets for use with Metric calipers. Welding is required. Designed for 3-1/2" axle tubes, but can be fit to 3" tubes.