No items in Shopping Cart
Here you get the hose, hose end fittings and fuel pump fitting if required. Choose from push-on steel or aluminum fittingswith blue hose, or aluminum fittings with stainless steel braided hose. AN8 hose only.
This fuel line is intended to connect two Edelbrock (or Carter) four-barrel carbs on a low-rise 2x4 intake. The inlet fitting thread is 3/8" NPT female, and there is a 1/8" NPT hole that can be used for a fuel pressure gauge. The outlets on this line can be as close together as 6-1/2" and as far apart as 8-1/4". All of the line is anodized blue, except for the central piece of braided stainless steel hose.
2 brass fittings, 14" pipe thread for 38" ID hose, 2 stainless hose clamps per set.
Speedway Red See-Through Fuel Line is the perfect old-time accent to your multi-carb street rod! This specially-formulated, flexible tubing has a 3/8" inside diameter and comes in 6 foot lengths. You can easily trim it to your needs. Works with normal slip-on hose barb fittings and clamps.
Easy to install! Easy to clean! Hi-tech detailing at an economy price. Each kit contains 3' of vacuum line, 4' of fuel line, 12' of heater hose, and an extra long 4-1/2' of radiator hose sleeving, and 4 shrink sleeves for vacuum lines, 4 fuel line fittings, 4 heater hose fittings, 2 fittings for upper radiator hose.
Aeroquip FC300 spec hose to be used as the fuel or power steering line. Hose only works with listed fittings (not included). Easily assembles with a bench vise and/or wrenches. Ends are reusable. Hose sold by foot.The AN6 high pressure hose has an ID of 0.31" and an OD of 0.67". The maximum operating pressure is 2250 psi and the minimum bend radius is 4". Its applications include: power steering lines, hydraulics, air, gasoline, fuel, lubricating oils, over the wall air tools, and DOT-approved air brakes. This high pressure hose ...
Black push-on hose available in AN6, 8, 10 and 12. Ideal for fuel line applications only -NOT suited for oil or water use exceeding temperatures of 200 F.
Aeroquip FC 300 spec hose to be used as the fuel or power steering line. Choose AN 10 and fittings required.
Aeroquip FC300 spec hose to be used as the fuel or power steering line. Hose only works with listed fittings (not included). Easily assembles with a bench vise and/or wrenches. Ends are reusable. Hose sold by foot.The AN8 high pressure hose has an ID of 0.41" and an OD of 0.77". The maximum operating pressure is 2000 psi and the minimum bend radius is 4.62". Its applications include: power steering lines, hydraulics, air, gasoline, fuel, lubricating oils, over the wall air tools, and DOT-approved air brakes. This high pressure hose ...
To make your LS1 transplant a little less painful, we put together these kits for you. If you already have a fuel pump in the tank, use the filter/regulator kit 910-12800. This kit includes a high pressure MSD in-line pump capable of 43 gph @ 40 psi or 39 gph @ 80 psi, a filter/regulator assembly, and all necessary fittings (including fuel rail fitting). Pump draws only 5.4 amps and supports up to 500 horsepower. Pump features 3/8" hose barb inlet and 5/16" barb outlet.
Eliminate ugly fittings and adaptors with this chrome dual feed line with mandrel bends and 3/8" hose barb, providing excellent fuel flow. For Holley 4160-style vaccuum secondary (side hung float bowl) 4-BBL carburetors with 8-21/32" centers.
This kit provides a complete fuel system for GM LS-series and Chrysler Hemi engine swaps in muscle cars, street rods and off-road vehicles. These kits include an in-line Edelbrock electric fuel pump, regulator/fuel filter assembly, fuel pump relay and wiring assembly, fifteen feet of ProFlex hose, plus an assortment of hose ends, adapters and mounting hardware.
These 3/8" fuel line kits have a clean look and are easy to install. Choose with or without fuel filter. These fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution. The drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing. The 325-8126 includes a barbed end for a push-on 5/16" or 3/8" rubber fuel line. The 325-8131 includes an aluminum fuel filter with a 40 micron filter element and -6 AN female inlet will accept an ...
High quality stainless steel construction with black anodized fittings are pre-bent for easy plumbing of your new blower system. All kits feature an 8 AN fuel inlet with a provision for a fuel pressure gauge.
Replacement set of O-rings for Kinsler bypass pill holder 3112. Includes (1) small O-ring and (1) largeO-ring.Compatible with both gas and methanol.
This braided pressure gauge line kit makes it a snap to hook up your pressure gauge. Can be used with oil, water, fuel or air. Includes AN 4 braided line, AN4 to 1/8" NPT male and AN4 to 1/8" NPT female. Choose from lengths of 25", 36" or 48".
61764860Material TypeAluminumFinishAnodizedColorBlueSold in QuantityEachNotesSnaps into GM 5/16" fuel line to AN6.
61764850Overall Length1.750" (1 3/4")Overall Diameter0.853"ColorBlueMaterial TypeAluminumFinishAnodizedSold in QuantityEachNotesSnaps into GM fuel rail.
61764853Fitting End ASnaps into 3/8" fuel lineFitting End BAN-6Material TypeAluminumFinishAnodizedColorBlackSold in QuantityEach
61764863Sold in QuantityEachNotesBlack Anodized, Snaps into a GM 5/16" fuel line to a AN6
We offer longer fuel lines to compensate for extra length between fuel bowls.
These slick inlet fittings have two AN6 ports built in to run your returns to. They screw into the AN8 inlet side of your fuel pump and allow either an AN10 or AN12 line to be used.
The 20 gauge steel can encloses a tough cross-link polyethylene cell.Includes fuel cell, steel can, IMCA required tip-over valve, and 4" diameter twist-on cap.Has a -8 AN fuel line hookup and return vent. Safety foam sold separately.
2 Gallon added capacityAll new steel reproduction tanksIncludes: Original-style extra-length mounting straps & hardware, sending unit gasket, and fuel injecion block-off plate & gasketComes with flange for fuel injection pickup or use fuel line outlet for carbAccepts original or other after market sending units from Stewart Warner, VDO, Classic and others
Brake and fuel lines are something you should mount right the first time. Using our stainless steel clamps ensures you never have to replace them. Single clamps are available in 3/16", 1/4", 5/16" or 3/8".
Brake and fuel lines are something you should mount right the first time. Using our stainless steel clamps ensures you never have to replace them. Dual clamps have 3/16" on one end with your choice of 3/16", 1/4" or 3/8" on the other end.