No items in Shopping Cart
Use this kit to control side-to-side movement of your front axle. Works with stock or dropped I-beam or tube axles, original or replacement front crossmembers.
Four barsuspensions allow your front axle to travel freely, thus providing better ride and handling than traditional radius rods. Plus, their polished stainless construction will keep your front end glowing forever! Speedway kitsfeature bat wings and tapped bar ends, complete with nylon rod ends. For axles with 2" or 2-1/4" boss - use spacers916-35003 if necessary.
1/8" spacers for V-style front spreader.
Kit includes:
Front and rear 1932 Ford straight cross bars. Front bars measure 23-1/4" long and have a 1-1/2" outer diameter and fit between the frame rails on a 1932 Ford.
V-Style cross bars for 1932 Ford are designed for a weld-in application. They have no end plates. Measure 23-1/4" wide with a 2" outside diameter.
These front spreader bars are the V-Style and have two of the bolts hidden to clean up the looks. Polished stainless steel construction gives good looks and low maintenance. Simple bolt-in design. Measures 23" wide with a 1-3/4" outside diameter.
These front end assemblies include a new tube or I-beam axle, new leaf spring and u-bolts, spring shackles, spring perches, lower shock mounts, 4-bars and ends and panhard bar assembly. Available plain or chrome.
Save yourself the searching and confusion with these complete '28-'31 Ford Model A front suspension kits. Each kit includes a 48" wide, 4" drop I-beam axle, our famous urethane-bushed 21" long four bar assembly, perch bolts, lower shock mounts, spring shackles, Super Glide spring and the necessary brackets and hardware needed for assembly.
Save yourself the searching and confusion with these complete '28-'31 Ford Model A front suspension kits. Each kit includes a 48" wide, 3" drop tube axle, our famous urethane-bushed 21" long four bar assembly, perch bolts, lower shock mounts, spring shackles, Super Glide spring and the necessary brackets and hardware needed for assembly.
Save yourself searching and confusion with these complete front suspension kits. Each kit includes a 48" wide, 3" drop tube axle, our famous urethane-bushed 21" long four bar assembly, perch bolts, lower shock mounts, spring shackles, Super Glide spring and the necessary brackets and hardware needed for assembly. (Spring and frame brackets are not stainless steel).
Includes 2 replacement perch bolts and 2 bolt-on frame brackets. No welding or cutting necessary. Typically used with stock or "split" wishbones. Works well wtih shock 582SM500 (or equivalent).
After more than fifty years of use, the original upper shock mounts on the front of your vintage Ford pickup are likely worn out, damaged or missing.These forged steel upper shock mounts are reproductions of those used on 1948-1952 Ford F1 trucks, but are also adaptable to other beam-axle trucks from the 1940's and 1950's.
When using original or reproduction frame rails, be sure to fully box the front section for strength and saftey. Our front boxing plates are designed to box the frame in critical front suspension attachment points and motor mount areas.
These weld-on 1932 Ford front frame horn boxing plates must be used with a V-style front cross bars.
Steel, Ford Roadster reproduction.
Speedway's exclusive steering & brake kits save you time and money by combining all necessary parts into one part number. Each kit includesbrake kit, spindles, dust caps, spindle nuts, Rubber Brake Lines, AN3 caliper fittings, kingpins, flat steeringarms, tie rod assembly and hardware.
Speedway's exclusive steering & brake kits save you time and money by combining all necessary parts into one part number. Each kit includesbrake kit, rubber brake lines, spindles, dust caps, spindle nuts, AN3 caliper fittings, kingpins, flat plate steeringarms, tie rod assembly and hardware.
Replacement bearing & seal kit for 1932-1948 Ford style fronthubs.Also for use with our 910-65450 front hubs. Outfits both front hubs (one entireaxle).
Use with original or reproduction Model "T" thru '34 Ford front crossmembers. Includes two chrome platedU-bolts with nuts, one plain steel spacer plate and one plain steel lower bracket.
If you still need a front axle assembly for your pre-2008 Total Performance T-Bucket, you had better read this. The Total Performance T-Bucket spindles were a hybrid that combined Econoline kingpins, early Chevy bracket mounting tabs and early Ford wheel bearing surfaces. Unfortunately these spindles are no longer being manufactured. Speedway has a kit that includes the axle, leaf spring, shackles, radius rods, '49-'54 Chevy car style spindles with kingpins and hardware. This kit will get you away from the hybrid spindles and allows you to run any of our ...
Speedways 3" Drop Tube Axles are a one-piece design featuring precision welded ends and perch bolt holes. Axle is formed from high strength 2" x .250" wall steel tubing. Use with 1937-48 Ford style spindles.
Achieve a smoother, more comfortable ride with one of Posies Super Slide(TM) springs! The ends of the spring leaves of a Super Slide(TM) spring have a unique "dimple" shape that retains amoly-nylon button whichworks as a dry lubricantto stop leaf-to-leaf interference. This freedom from friction lets the spring move more easily, thereby giving a softer, quieter ride.
91033050Material TypeSteelFinishNaturalSold in QuantityPairNotesTapered OEM castle nut.
Use with original or reproduction Model "T" thru '34 Ford crossmembers. Includes two U-bolts with nuts, one spacer plate and one lower bracket.