No items in Shopping Cart
Flush-mount caps offer excellent aerodynamic performance, large fill opening and attractive appearance. Cap features a positive seal, flip-up 1/4-turn handle, and a chain to secure it to the neck.Includes cap, chain, neck, gasket, and all hardware.Polyethylene cap is vented.Hole in tank needs to be 3-3/4" for cap to sit flush.
These filler necks come with a vented cap which vents to the underside of the cap. Steel weld-in 2.25" O.D. bung.Cap locks on the inside of the neck, not on the outside like a radiator cap.
These filler necks come with a vented cap which vents to the underside of the cap. Weld-in 2.3" O.D. bung.Bung is aluminum.
6175022Overall Length3.190"Overall Height0.560"Outside Diameter2.680"Material TypeSteelFinishZincSold in QuantityEach
This neck allows you to fill your cooling system at the intake manifold if you radiator is lower than the intake. It can be flipped over for RH or LH upper hoses, and has two 1/4" npt and one 1/2" npt hole in the back for bypass lines or sending units.Fill cap plate has a 7/16" pipe nipple welded into the overflow area.
Weld-in 2.3" O.D. bung. This aluminum filler neck bung includes a flange. Features vented cap which vents to the underside of the cap.
These 1-1/2" inline hose adaptors allow you to put either a radiator fill cap inline. Use with a bleeder valve to get all air out.
Replacement fuel cell cap fits 4" necks like those on our Steel Can Fuel Cells,Polyethylene Fuel Cells, and on our 4" Filler Neck Kit 910-76505.
Graceful, swept-back wing shape adds class and style to any Model T. Screws onto filler neck.*
Designed for use with Hex Cap, Moto-Meter, or Dogbone**. Solder it onto your radiator or secure it with a long bolt through the center.
Graceful, swept-back wing shape adds class and style to any Model T. Screws onto radiator filler neck.*
Graceful, swept-back wing shape adds class and style to any Model T. Screws onto filler neck.* Accepts motor meters.
Graceful, swept-back wing shape adds class and style to any Model T. Screws onto filler neck.* Accepts motor meter.
AFCO's billet aluminum radiator filler necks offer improved strength and appearance over stamped versions comes. Comes with a 1/8" aluminum hose nipple.
Makes manifold the highest filling point. For cooling problems where radiator is mounted low. Fits both right or left applications. Sender mount. Fits GM V8, 90 V6.
This inline filler neck installs into 1-1/2" O.D. upper radiator hoses. 100% aluminum construction. Includes a 1/8" straight aluminum overflow hose barb.
1906-1916 Model T style radiator filler neck designed for use with hex radiator caps or dog bone radiator caps. Solder it onto your radiator or secure it with a long bolt through the center of the grille shell.
91676550Overall Diameter5.000"Inside Diameter1.750" (1 3/4")Hose ID2.000"Material TypeAluminumSold in QuantityEachNotes6 mounting holes on a 4.36" bolt circle. Includes mount ring, bolts and gasket.
This 4" diameter filler neck kit can be used as a replacement unit or for your custom fuel cell. Kit includes a mounting ring, rubber gasket, and bolts.
This flange bolts to your fuel cell to permit attachment of a 1-1/2"I.D. filler hose. Aluminum construction.
Replacement gasket for 4" fuel cell filler neck #910-76505.
Heavy aluminum constructionHardware and seal included
These 15 gallon aluminum fuel tanks are designed to be mounted under your pick-up box. The 1-1/2" filler neck will require a remote filler neck or fuel filler door in the box floor. They DO NOT accept the original truck fuel sending unit, but do accept the common sending unit provided with aftermarket gauge sets.
These 17 gallon aluminum fuel tanks are designed to be mounted under your pick-up box. The 1-1/2" filler neck will require a remote filler neck or fuel filler door in the box floor. They DO NOT accept the original truck fuel sending unit, but do accept the common sending unit provided with aftermarket gauge sets.