No items in Shopping Cart
These 429-460 Ford motor mount kits allow you to put that 'little bit different' engine in your project. They have urethane bushings and include both the engine and frame brackets. Frame brackets must be cut to fit and welded to frame.
These LS1/LS6 Chevy motor mount kits allow you to put that "little bit different" engine in your project. They have urethane bushings and include both the engine and frame brackets. Frame brackets must be cut to fit and welded to frame.
These New Style 5.7 Hemi motor mount kits allow you to put that 'little bit different' engine in your project. They have urethane bushings and include both the engine and frame brackets. Frame brackets must be cut to fit and welded to frame.
These 401-425 Nailhead Buick motor mount kits allow you to put that "little bit different" engine in your project. They have urethane bushings and include both the engine and frame brackets. Frame brackets must be cut to fit and welded to frame.
Put a 283-400 S/B Chevy in your 1988-2000 2wd S-10 or S-15 using stock 4.3L V-6 motor mounts.
On your '55-'57 Chevy car, the front motor mounts are at the front of the block and the rear mount attaches to the bellhousing. This works fine for original use, but makes it hard to swap in a different tranny or add belt driven accessories to the front of the engine. This mount kit is the solution!
Specially designed engine mount cradle to mount your 1958-1964 Chevy 348-409 W-motor into almost any chassis. Includes Grade 5 mounting hardware. Add one of our frame mount kits and a universal bolt-through cushion kit for a professional installation.
Small Block Chevy bolt-in motor mounts for use withSpeedway '47-'54 Chevy Pickup Mustang II Bolt-In Crossmember # 910-44754. Kit includes steel frame mounts, steel engine mounts, rubber cushion set, and all hardware.
Side-mount motor mounts are amore rugged mount design than the original front mounts found on your Tri-Five Chevy, plus they allow more room for front drive accessories. Our motor mount kit allows you to side-mount 1958-up S/B Chevy 283-400 c.i. V-8 enginesinto your 1955, 1956,or 1957 Chevy passenger car.
These S/B Fordmotor mounts have a rubber bushing inthem giving you a vibration free installation. Welding and fitting required.
This weld-on universal motor mount fits most frames.At the point where this mounts to the engine it is 2 1/2" long andaccepts a 1/2" inch bolt. The base is 4 1/2" wide at the top, and 5" wide at the bottom.
Adapts small block (289, 302, 351W) Ford V8s into 4 wheel drive Jeeps, model MB, CJ2, CJ3A, CJ3B, CJ5, CJ6, CJ7, C101, also fits some 1948-1962 Utility series, station wagons, panels, & Jeepsters. Plates weld-on.
If your race vehicle reqires rigid motor mounts, our solid steel mounts won't let you down. Theseenginebrackets aredesigned to be used with our SteelFrame Mounts 545-62630.
91618956Overall Thickness0.250" (1/4")Material TypeSteelFinishZincSold in QuantityPairNotesFits S/B and B/B Chevy. From center of bottom bell housing bolt hole out to the center of the base mount bolt hole is 4-5/8"
Steel mounts prevent twist during hard accelerations.Replaces stock upper mounts. Measures 1-11/16" high, 2-1/2" wide.
More often than not, we are trying to put an engine in something that no one has built bolt-in mounts for. If that's your story, we have just the deal for you! This S/B Chevy and B/B Chevy motor mount has a poly bushing in it giving you a vibration free installation.
Some chassis have no room for an engine mount crossmember. For them we offer these mounts. Bolt-to-frame brackets are easy to install. Heliarc welded steel. Mounts S/B Chevy on 1935-1940 Ford frame rails.
These 3-bolt S/B Chevy rubber motor mounts aremanufacturedto meet or exceed OEM specifications. Fits most 1958-73 Chevy passenger cars with Small Block V8. Sold as a pair.
These 2-bolt S/BFordrubber motor mounts aremanufacturedto meet or exceed OEM specifications. Fits most 1965-78Fordfullsize passenger cars with Small Block 289, 302, and 351W V8s. Sold as a pair (left & right side).
Chevy V8s into 1953-1964 Ford pickup & panel trucks. Plates bolt-in.
If your race vehicle reqires rigid motor mounts, our solid steel mounts won't let you down. These framebrackets aredesigned to be used with our steel motor mounts 545-62515.Fits both Small Block and Big Block Chevy.
Our billet motor mounts are machined from 2025 aluminum and include bushing inserts. Fully polished finish. Includes universal frame adaptors.
Cross bar style. Mounts Ford 332-428 (except 351/400) V8's into 1953-1964 Ford pick-up and panel trucks. Designed for 28-34" frame widths. Complete with instructions and hardware.
Chevy V8s into 4 wheel drive Jeeps, model MB, CJ2, CJ3A, CJ3B, CJ5, CJ6, CJ7, and C101. Also fits some 1948-62 Utility series, station wagons, panels & Jeepsters (except J series). Frame plates weld-on.