Build a mock Boss 351 engine with a standard 351W block and 351 Cleveland heads using this Performer RPM E-Boss 351 manifold. For both high performance street and competition the dual-plane design makes outstanding power from 1500 to 6500 rpm and the Cleveland port layout and intake bolt hole pattern fit both 2V and 4V heads. It features 9.5" deck height Windsor end rails water neck and distributor hole clearance front and rear water bosses with a standard square bore carburetor pad.Edelbrock carbs will work with Ford automatic overdrive trans ...
Based on the powerful Performer RPM Vortec #7116, single four-barrel intake is designed for 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or the new Edelbrock E-Tec aluminum heads.The RPM Air-Gap manifold delivers outstanding performance using the same air-gap technology found in our race-winning Victor manifolds. This unique design separates the hot engine valley from the air/fuel mixture for a cooler, denser charge and more power throughout the rpm range. An external water bypass boss is machined into the front of the water crossover for use ...
Based on the proven Performer RPM Vortec this single four-barrel intake is designed for 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or Edelbrock E-Tec aluminum heads. The unique Air-Gap design separates the hot engine valley from the air/fuel mixture for a cooler denser charge and more power throughout the rpm range. An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines. Includes rear water outlets nitrous bosses a temp sensor boss that ...
Performer RPM Dual-Quad intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W" Series engines. These manifolds deliver performance improvements in the 1500-6500 rpm range with Edelbrock Performer Series dual-quad carburetors, and they accept Edelbrock dual-quad accessories including fuel lines, throttle linkage, and air cleaners. Includes oil fill tube (not installed) and matching push-in breather cap. Use with dual quad linkage and fuel line at right. Carb center-to-center measurement is 6-7/16". 325-5408 Instructions (PDF)
Based on the powerful Performer RPM Vortec #7116 single four-barrel intake is designed for 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or the new Edelbrock E-Tec aluminum heads.The RPM Air-Gap manifold delivers outstanding performance using the same air-gap technology found in our race-winning Victor manifolds. This unique design separates the hot engine valley from the air/fuel mixture for a cooler denser charge and more power throughout the rpm range. An external water bypass boss is machined into the front of the water crossover for use ...
This intake is for you guys required to run the GM Phase 3 cast iron Vortec Bowtie heads. Fits head part numbers 25534421, 25534351, 25534431 and 25534371. The carb pad is raised to increase plenum volume and the runners are raised to increase airflow. 4000-8000 RPM Features the original 6-bolt pattern 7/8 inch of additional carb pad height
Edelbrock Performer intake manifolds are low-rise dual-plane designs with patented runner tuning and a 180 degree firing order that you won't find with the competition. This combination boosts torque over a wide rpm range from idle to 5 500 rpm. These manifolds also deliver improved throttle response over stock intakes.Stock/OEM standard deckDual plane - idle - 5 500 rpmNatural aluminum finishNon-EGR325-02114 Instructions (PDF)Notes: This intake manifold must be used with 1996 and later Vortec style cylinder heads (even if they are installed on pre-Vortec blocks). Accepts late model water ...
Designed for 396-454 c.i.d. big block Chevy withrectangular port heads. Has an optimum power range of 1500-6000 rpm. Edelbrock testing has confirmed smooth consistent part-throttle operation with a 25 hp gain over single 4BBL low-rise single plane intakes and a torque gain of 30 ft/lbs. over single 4BBL low-rise dual plane intakes. Carb center to carb center is 6-7/16"Will NOT fit tall-deck truck blocksCarburetor Recommendation: Performer Series 600 cfm 325-5421 Instructions (PDF)
Designed for 1975 & earlier 396-454 c.i.d. big block Chevy with oval port heads. Has an optimum power range of 1500-6000 rpm. Edelbrock testing has confirmed smooth consistent part-throttle operation with a 25 hp gain over single 4BBL low-rise single plane intakes and a torque gain of 30 ft/lbs. over single 4BBL low-rise dual plane intakes. Carb center to carb center is 6-7/16"Will NOT fit tall-deck truck blocksCarburetor Recommendation: Performer Series 600 cfm 325-5420 Instructions (PDF)
Give your FE-powered hot rod dual-quad power and nostalgic looks with the new Edelbrock RPM Air-Gap Dual-Quad intake manifold. Designed for 1960-later high-performance street 390-406-410- 427-428 c.i.d. Ford FE engines with a 1500-6500 rpm power band. The manifold carb pad is setup to fit Edelbrock carburetors only will not work with other square flange carburetors. Will not fit 427 Ford Hi-riser and Tunnel port engines. Has provision for a breather flange at rear. Carb center spacing 6-7/16" In Dyno tests on a 390 with Performer RPM heads Performer RPM camshaft ...
In the '60s if you wanted the baddest car in town you needed dual quads under the hood and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 260-289-302 small-block Ford V8. These Small Block Ford intakes are taller offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler denser charge and more horsepower. Carb center spacing is 6-7/16".Small Block Ford Dual Intake Manifold Installation ...
In the '60s if you wanted the baddest car in town you needed dual quads under the hood and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 351W small-block Ford V8s. These intakes are taller offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler denser charge and more horsepower. Carb center spacing is 6-7/16".325-7585 Instructions (PDF)
Designed for 1986 and earlier 262-400 cubic-inch Chevys the Performer EPS dual-plane manifold is optimized to deliver superior performanceover other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it producespower from off-idle to 5500 rpm. Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over thestandard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm the increases averaged 5+ ft/lbs. of torque for more performance where you need ...
Edelbrock's C-26 manifold is designed for 1955-1986 262-400 c.i.d. S/B Chevys with a power band of 1500-5000 rpm. This dual-quad is low profile for hood clearance on most vehicles. Air-conditioning bosses and front oil filler tube boss included. Stock alternator brackets DO NOT fit. H.E.I. distributor will fit. Use with 500 cfm Edelbrock carbs.Dual Quad Intake Manifold Installation Instructions (PDF)
Performer RPM Dual-Quad intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W" Series engines. These manifolds deliver performance improvements in the 1500-6500 rpm range with Edelbrock Performer Series dual-quad carburetors and they accept Edelbrock dual-quad accessories including fuel lines throttle linkage and air cleaners. Includes oil fill tube (not installed) and matching push-in breather cap. Use with dual quad linkage and fuel line at right. Carb center-to-center measurement is 6-7/16".325-5409 Instructions (PDF)
Performer RPM Dual-Quad intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W" Series engines. These manifolds deliver performance improvements in the 1500-6500 rpm range with Edelbrock Performer Series dual-quad carburetors and they accept Edelbrock dual-quad accessories including fuel lines throttle linkage and air cleaners. Includes oil fill tube (not installed) and matching push-in breather cap. Use with dual quad linkage and fuel line at right. Carb center-to-center measurement is 6-7/16".325-5408 Instructions (PDF)
The Performer RPM W-Series intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W-Series" big-block engines. Two versions are available; one for small-port cast iron heads and the other for factory large port heads. They both deliver improved performance in the mid to high rpm range (1500-6500 rpm) when combined with an Edelbrock Performer carburetor. Both also feature a front mounted oil fill tube for those who want the nostalgic look of Edelbrock's Classic series valve covers with no breathers. Includes chrome oil fill tube (not installed) and matching push-in ...
The Performer RPM W-Series intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W-Series" big-block engines. Two versions are available; one for small-port cast iron heads and the other for factory large port heads. They both deliver improved performance in the mid to high rpm range (1500-6500 rpm) when combined with an Edelbrock Performer carburetor. Also features a front mounted oil fill tube for those who want the nostalgic look of Edelbrock's Classic series valve covers with no breathers. Includes chrome oil fill tube (not installed) and matching push-in breather ...