Tru-Ram® Exhaust Manifolds allow you to enjoy the nostalgic look of factory BBC style manifolds, without sacrificing any performance. Investment cast from durable stainless steel material, these exhaust manifolds will be a low maitenance, high-performance addition to any Big Block Chevy-powered vehicle. Features a fully polished, show-quality finish. High-performance tubular design Smooth internal transitions perform like shorty headers Tightest fit to block available Added clearance for steering shaft Round 1-7/8" primary tubes with large 3" collector outlet Standard 3 bolt collector ...
If you already have a blower and drive, we offer just the intake. Adapt 6-71 superchargers to Small Block Chevy. Cast aluminum, they feature an integral pop-off valve and utilize stock-type thermostats and housings.
No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold. These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration. They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole. There is an air gap under the front water crossover for extra cooling and an extra tapped water port. These manifolds have permanent mold castings for accurate port placement, tighter ...
If you already have a blower and drive we offer just the intake. Adapt 6-71/8-71 superchargers to Big Block Chevy. Cast aluminum they feature an integral pop-off valve and utilize stock-type thermostats and housings.Rear Mounted Pop Off Plate (Included)Standard deck onlyBoost Gauge port
Tru-Ram® Exhaust Manifolds allow you toenjoy the nostalgic look offactory BBC style manifolds without sacrificing any performance. Investment cast from durable stainless steel material these exhaust manifolds willbe a low maitenance high-performanceaddition to any Big Block Chevy-powered vehicle. Features a fully polished show-qualityfinish. High-performance tubular designSmooth internal transitions perform like shorty headersTightest fit to block availableAdded clearance for steering shaftRound 1-7/8" primary tubes with large 3" collector outletStandard 3 bolt collector patternIncludes ...
No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold. These 360° manifolds feature dual distributor hold downs for Chevy four corner water outlets and line of sight port configuration. They also have extended port dividers thermostat recess and an accessory bracket boss and tapped hole. There is an air gap under the front water crossover for extra cooling and an extra tapped water port. These manifolds have permanent mold castings for accurate port placement tighter ...
The Power+Plus Cyclone Manifold is a direct replacement manifold for the stock manifold on Chevy big block engines with general duty oval port heads. This dual plane intake will accept either a Quadra-Jet or square flange carb (with supplied adapter plate). Also features nitrous bosses cast in for use with direct port systems. RPM range is idle to 6000. Available plain, polished or chrome. This product comes with the adapter/cover plate for the OEM choke assembly to bolt to. It also has the adapter/cover plate gasket and two allen head chrome ...
No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold. These 360° manifolds feature dual distributor hold downs for Chevy four corner water outlets and line of sight port configuration. They also have extended port dividers thermostat recess and an accessory bracket boss and tapped hole.There is an air gap under the front water crossover for extra cooling and an extra tapped water port. These manifolds have permanent mold castings for accurate port placement tighter grain ...
The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally each Power+Plus Manifold is 100% pressure ...
The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds, not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally, each Power+Plus Manifold is 100% pressure ...
If you are running a little more motor, then this is the intake for you! The Professional Products Typhoon manifold is a high performance dual plane, 180° street manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters. RPM range is 1500-6500 Available plain, show polished or chrome Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane Cast-in nitrous bosses Water outlets at all four corners Dual distributor hold-downs Provisions to ...
The Professional Products Cyclone manifold is the ideal street manifold for street rods or engine swaps using the popular1996 and later Vortec (L31) cast iron heads. Manifold includes adapter to use a square bore carb andfeatures dual distributor hold downs. Also includes two pipe tapped rear water ports. Available for plain or polished.Fits Vortec blocks or 1995 & earlier blocks with Vortec heads. RPM range is idle to 5500.Chevy Vortec Manifold Installation Instructions(PDF)
If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower. RPM range is 1500-6500 Available plain or show polished Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane Cast-in nitrous ...
The Power+Plus Cyclone Manifold is a direct replacement manifold for the stock manifold on Chevy big block engines with general duty oval port heads. This dual plane intake will accept either a Quadra-Jetor square flange carb (with supplied adapter plate). Also features nitrous bosses cast in for use with direct port systems. RPM range is idle to 6000. Available plain polished or chrome. This product comes with the adapter/cover plate for the OEM choke assembly to bolt to. It also has the adapter/cover plate gasket and two allen head chrome ...
If you are running a little more motor then this is the intake for you! The Professional ProductsTyphoon manifold is a high performance dual plane 180° street manifold designed to be used with Holley Carter AFB or Edelbrock squareflange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters.RPM range is 1500-6500Available plain show polished or chromePower comparable to single plane manifolds yet retains throttle response/driveability of a dual planeCast-in nitrous bossesWater outlets at all four cornersDual distributor hold-downsProvisions to add an oil fill ...
The Power+Plus Cyclone Manifold is a direct replacement manifold for the stock manifold on Chevy big block engines with general duty oval port heads. This dual plane intake will accept either a Quadra-Jet or square flange carb (with supplied adapter plate). Also features nitrous bosses cast in for use with direct port systems. RPM range is idle to 6000. Available plain, polished or chrome. This product comes with the adapter/cover plate for the OEM choke assembly to bolt to. It also has the gasket and two allen head chrome cap screws ...
These Performer RPM intake manifolds are dual-plane, high-rise intakes with 180° firing order to produce incredible top-end horsepower while retaining good throttle response. Their larger plenums and runners match the free-flowing exhaust, high-lift cams and other modifications of a high output engine. They are intended for high-performance street or competition engines that run up to 6500 rpm. They are not recommended for emissions equipped engines. Edelbrock's exclusive Endurashine finish is a three-step coating that has the brilliance of chrome or a well-polished piece, but without the ...
These Performer RPM intake manifolds are dual-plane high-rise intakes with 180° firing order to produce incredible top-end horsepower while retaining good throttle response. Their larger plenums and runners match the free-flowing exhaust high-lift cams and other modifications of a high output engine. They are intended for high-performance street or competition engines that run up to 6500 rpm. They are not recommended for emissions equipped engines.Edelbrock's exclusive Endurashine finish is a three-step coating that has the brilliance of chrome or a well-polished piece but without the ...
If you already have a blower and drive, we offer just the intake. Adapt 6-71/8-71 superchargers to Big Block Chevy. Cast aluminum, they feature an integral pop-off valve and utilize stock-type thermostats and housings. Rear Mounted Pop Off Plate (Included) Standard deck only Boost Gauge port