Don't sacrifice your acceleration due to a heavy flywheel. For 1955-1985 internally balanced 153 tooth small block Chevy applications. Typically used with 10-1/2" Ram solid hub clutch disc 605-351 and pressure plate 605-401 Will also work with a Ram 605-301M sprung hub or 605-1021 6-pad clutch disc
Don't sacrifice your acceleration due to a heavy flywheel.For 1955-1985 internally balanced small blockChevy applications. Made of 1045 billet steel168 tooth Use 11" clutchNote: Not for use with stock clutch disc as springs on friction disc hub will not clear flywheel bolts.
Don't sacrifice your acceleration due to a heavy flywheel. For 1955-1985 internally balanced small block Chevy applications. Made of 1045 billet steel 168 tooth Use 11" clutch Note: Not for use with stock clutch disc as springs on friction disc hub will not clear flywheel bolts.
RAM billet steel flywheels are recommended as replacements for factory cast flywheels in high performance and racing vehicles. Cast flywheels are not explosion proof and can be dangerous when used in high performance applications at higher RPMs. RAM billet steel flywheels are CNC machined from certified materials and exceed SFI specifications. After machining, the flywheels are blanchard ground parallel to the crankshaft mounting surface ensuring minimum runout and the optimum mating surface for the clutch disc. Use steel flywheels in heavier drag race cars or for the best driveability in ...
These Ram 10 lb. racing flywheels are made of billet steel, not a cast stock piece cut down. Will work with 10.5" B&B or diaphram style pressure plates. These flywheels MUST use a solid hub friction plate (sprung hubs will not clear). Note: This flywheel requires very short bolts for mounting, as it is very 'thin' in the center. Use ARP flexplate bolts # 101-2002902.
These strong lightweight steel bellhousings from Quick Time are just the ticket for installing a manual transmission behind your Small Block or Big Block Chevy V-8. The compactdesign allows the bellhousings to fit in tight quarters while still accommodating a 10-1/2" clutch. Must be used with a hyraulic throwout clutch release bearing and a mini starter.Lightest steel bellhousing available anywhereCone is spun (not rolled or stamped) for extreme dimensional stability High grade steel — work hardens to over 80 000 PSI strengthOver 2 times the strength of any other steel ...
By installing a lightweight aluminum flywheel, you automatically bolt on up to 15 horsepower to the wheels. Your engine will reach higher RPMs quicker, due to lighter rotating mass. Manufactured from 6061-T6 billet aluminum Can be used with any type of clutch friction material Locked locating dowel pins SFI approved Works with 10-1/2" (10.4") Diaphragm or Borg & Beck pressure plates Weighs 10.84 lbs 12 7/8" in diameter
By installing a lightweight aluminum flywheel youautomatically bolt on up to 15 horsepower to the wheels. Your engine will reach higher RPMs quicker due to lighter rotating mass. Manufactured from 6061-T6 billet aluminumCan be used with any type of clutch friction material Locked locating dowel pinsSFI approvedWorks with 10-1/2" (10.4") Diaphragm or Borg & Beck pressure platesWeighs 10.84 lbs12 7/8" in diameter
By installing a lightweight aluminum flywheel for your SBC youautomatically bolt on up to 15 horsepower to the wheels. Your engine will reach higher RPMs quicker due to lighter rotating mass. Made from 6061-T6 billet aluminumCan be used with any type of clutch materialLocked locating dowel pinsSFI approvedWorks with 10-1/2" (10.4") and 11" Diaphragm or Borg & Beck pressure platesInside hole dimension is 2.488 I.D. 14 1/8" in diameter
Extreme Duty SFI Approved Flexplate CHEV Small Block V8 1986-97 153 Tooth 1 Piece Rear Seal Internal Balance 4mm thick centerplate
These Ram 11 lb. racing flywheels are made of billet steel, not a cast stock piece cut down. Will work with 10.5" B&B or diaphram style pressure plates. These flywheels MUST use a solid hub friction plate (sprung hubs will not clear). Note: This flywheel requires very short bolts for mounting, as it is very 'thin' in the center. Use ARP flexplate bolts # 101-2002902.
By installing a lightweight aluminum flywheel for your SBC, you automatically bolt on up to 15 horsepower to the wheels. Your engine will reach higher RPMs quicker, due to lighter rotating mass. Made from 6061-T6 billet aluminum Can be used with any type of clutch material Locked locating dowel pins SFI approved Works with 10-1/2" (10.4") and 11" Diaphragm or Borg & Beck pressure plates Inside hole dimension is 2.488 I.D. 14 1/8" in diameter