Available for small block Chevy, GM LS or Ford applications. Each kit includes: Weld on frame pads Rubber bolt through cushion Engine pads Hardware
This weld-on universal motor mount fits most frames. At the point where this mounts to the engine it is 2 1/2" long and accepts a 1/2" inch bolt. The base is 4 1/2" wide at the top, and 5" wide at the bottom.
Mounting bracket sets off frame rail 2 inches for clearance Push rod center is 4 inches from frame rail mounting bracket Uses standard GM booster with 4 bolt mounting holes, 3-3/8" centers 10-1/2" tall brake pedal arm with clevis and push rod Pedal arm has 1/2" hole for pedal pad. Mounting hardware included
These headlight and shock mounts were designed for our T-buckets, but they can be used for a variety of projects. Can be easily bolted onto the outside edge of your frame rail. Mounts have 1/2" holes for Dietz style or other headlights Has two different 1/2" hole locations for upper shock mounting Measures 6" from the upper shock mount hole to the top of the frame rail
5/16" mounting holes 2" center to center 1/2" ID sleeve for light mounting bolt Great for headlights and taillights Use with mounting cups 91061034
Universal seat mount for our lowback vinyl seat # 910-1400. This 'universal fit' base can be cut/redrilled/modified to make it fit many applications. It is approximately 2" tall and has a footprint of 15-5/8" front to back and 19" from side to side. LH and RH sides sold separately.
Universal weld-on shock mount for bearing end shocks (spherical bearing or heim). Has a 1/2" hole and measures 2" L x 2" W x 1.5" H.
Universal weld-on shock mount for bearing end shocks (spherical bearing or heim). Has a 1/2" hole. Use short pin in place of shock bolt on this bracket.
Universal weld-on shock mount for bearing end shocks (spherical bearing orheim). Has a1/2" hole and measures 2" L x 2" W x 1.5" H.
Universal weld-on shock mount for bearing end shocks (spherical bearing orheim). Has a1/2" hole. Use short pin in place of shock bolt on this bracket.
Steel u-joint and crank flange for either early or late small block chevys.
Universal seat mount forour lowback vinyl seat # 910-1400. This 'universal fit'base can be cut/redrilled/modified to make it fit many applications. It is approximately2" tall andhas a footprint of 15-5/8" front to back and 19" from side to side. LH and RH sides sold separately.
Made from 1-3/4" Steel Tubing, Robotic Laser Cut & Welded, Powder Coated for brilliant, tough lasting finish. Universal mounts fits most TV’s and Monitors up to 32". Simple Bolt-On mounting. For that personal touch and “In Your Face” Racing experience that puts the track right in front of you.
Mounts below dash Sandwiches firewall between bracket and booster/master Includes adjustable pushrod
If you are building a lightweight car like a "T" or an "A", mounting the body may present a problem. These neat expanding rubber universal body mounts allow you to drill a 3/4" hole in the top of the frame, insert a 3/8" coarse bolt, tighten, then the body is mounted. Not recommended for cars newer than 1934.
Universal lower floor mount plate works on all 1-3/4" 2" or 2-1/4" diameter steering columns by simply removing the locking inter rings to the size of your column. Made out of chrome-plated aluminum for a clean finish. Measures 4-1/2" O.D. 2-1/4" column can make it to about 10 degrees 2" column can make it to about 17 degress 1-3/4" column can make it to about 30 degrees
If you want to shoehorn an Early Hemi in your Hot Rod we've got you covered. These mounts bolt to the side of the block and allow you to use our bolt-thru cushion kit. They have two sets of cushion holes to allow for different frame widths. The frame mounting bracket is up to you to design and build.For the following side tab configuration on the block:Drivers Side - 2 holes to the front & 1 hole to the rearPassenger Side - 2 holes to the rear & 1 hole ...
If you want to shoehorn an Early Hemi in your Hot Rod, we've got you covered. These mounts bolt to the side of the block and allow you to use our bolt-thru cushion kit. They have two sets of cushion holes to allow for different frame widths. The frame mounting bracket is up to you to design and build. For the following side tab configuration on the block: Drivers Side - 2 holes to the front & 1 hole to the rear Passenger Side - 2 holes to the rear ...
Universal upper coil spring mount for basic coil spring suspensions. Accepts 3-1/4" min I.D. and 4-3/8" max O.D.springs.
Universal mount fits 260-289-302-351W S/B Fords and 1970-1974 Cleveland engines into most frames up to 38" wide. Cut for frame width, then bolt or weld in. Note: We've found a lot of variation in width of Ford blocks. Bolt the cushion to the block first to get proper width measurement. Mounts are not returnable once they've been altered or installed!
Universal mount fits 260-289-302-351W S/B Fords and 1970-1974 Cleveland engines into most frames up to 38" wide. Cut for frame width then bolt or weld in. Note: We've found a lot of variation in width of Ford blocks. Bolt the cushion to the block first to get proper width measurement. Mounts are not returnable once they've been altered or installed!
Universal fit motor mounts. Heat treated aluminum construction. Fits S/B B/B 90° V6 Chevy.Use withcushion kit # 7209314.
Universal upper coil spring mount for basic coil spring suspensions. Accepts 3-1/4" min I.D. and 4-3/8" max O.D. springs.