(0)
Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Large Image
CLOSE [X]

Wilwood Reverse Swing Mount Dual Master Cylinder Pedal Assembly

Price:$231.99
Dual Master Cylinder Pedal Kit With Reverse Mount
Price:
$231.99
KT
Item #:
91029972
Open Kit Components
- Selection of individual components may be necessary for kit purchase.
Kit Components
340-5181 - Wilwood Dual Master Cylinder Pedal, Reverse Mount
Item #:
8353405181
1
  Show Specifications
  • 8353405181
    Overall Length
    15.000"
    Overall Width
    5.250" (5 1/4")
    Pedal Length
    11.875" (11 7/8")
    Bolt Hole Pattern
    3.00" x 4.25"
    Material Type
    Aluminum
    Finish
    Painted
    Sold in Quantity
    Each
260-6764 - Wilwood High Volume Master Cylinder
Item #:
835260676
260-6764 - Wilwood High Volume Master Cylinder
Item #:
835260676
 
(1 Rating)
Click image to enlarge Click image to enlarge
No video at this time.
 

Dual reverse pedal mounts two brake master cylinders with a bias balance bar. Wilwood's clevis and pivot pin balance bar provide smooth and accurate settings of the brake pedal bias. It can be set and locked down with the jam nut, or attached to a remote cable for quick on-track adjustments. 6.25 to 1 pedal ratio. Master cylinders have single 1/8" NPT outlets.

  • Positions master cylinders inside the firewall away from engine heat
  • Aluminum frame and arm construction
  • Steel pivots and mounting studs
  • Anti-skid pedal pad

910-29972 Instructions (PDF)

  • Pedal Arm is 11-7/8" from center of pivot to end of pedal
  • Overall lengthof pedal is 14-1/2"
  • Length of mount bracket is 4-5/8"
  • Width of mount bracket is 5-3/16"
  • Height of mount bracket is 3-1/8"
  • Mount bolt pattern is 3" front to rear and 4-1/4" side to side
  • Master cylinder mount pattern is 2-1/4" center to center vertical
  • The length of the master cylinder from the mounting flange is 5" 
Reviews for Item #: 91029972
Displaying Reviews 1 of 1
Processing
 

dems da brakes

By Mike 38 from Waterloo, IN on 5/2/2010
Pros:
Installed easy, No leaks, Stops 3500lb car
Cons:
Does not make car faster, Expensive
Best Uses:
Building calf muscles, Making hydraulic pressure
Bottom Line: Yes, I would recommend this to a friend

Works fine. if you want your master cylinder on the same side of the firewall as the driver then reverse mount is the way to go. These are expensive, but unfortunately worth it. stock brakes for a street stock class are prone to problems (leaks, vacuum issues, etc) and heavier than this setup. I would like to see the price lower, but no issues with quality, fit or finish.

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

Displaying Reviews 1 of 1
 

Questions and Answers for Item #: 91029972

Get your questions answered by the community. Ask or answer questions below.

2 Questions | 1 Answer
Displaying Questions 1-2 of 2
Processing

Q:

just a length from pedel pivit point to end of m/c please

Asked on 12/31/2010 7:30:30 PM by ron from nsw AUSTRALIA

Answers (1) Know the answer? Answer this question

Q:

does Dual Master Cylinder Pedal Kit With Reverse Mount Item #: 91029972 work with four wheel drum on a 2500 lb vehicle

Asked on 1/19/2011 7:47:15 AM by from

Know the answer? Answer this question
This question has not been answered. Click "Answer this question" above to submit an answer.
Displaying Questions 1-2 of 2

Do you have a question about this product?

Email this page
Close [x]
You can send this product by email to a friend!
Enter the required information in the spaces provided below. They will receive an Email with the picture of this product and a link back to our site.
Your Name:
Your Email:
Friends Name:
Friends Email:
Print Page