Sweet Mfg Steering U-Joint, 13/16 36-Spline to 3/4 Round, Big GM Pre 1978

							                        

                                                        These solid steering shafts are made for you to cut to fit. 3/4" O.D. 1018 solid steel shaft. Available in 24", 36", 48", 60" and 72" lengths. 
Steer Shaft Application Chart
 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. Made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.
Overall length is 5-1/2”
O.D. at ends is 1.12”
O.D. in the middle is 1.476”
O.D. at caps is 1.350”
O.D. at cap retainer screws is 1.545”
Length of center section is 2-3/4”
Spline Size (Link)
Steering Box/Rack/Spline Chart (Link)
 
                                                    

						                        

							                        

                                                        It's pretty silly to use plain old steel double d shaft with those shiny stainless steel u-joints. We offer this polished stainless steel double D shaft in 18", 22" and 36" cut to fit lengths. 
                                                    
						                        

							                        

                                                        
Steel coupler is splined on one end and has a 3/4" round hole on the other.  
Fits big GM gear box for pre 1978 vehicles. 
When ordering, select applicable hole size/spline needed.
Warning: This coupler is splined 13/16 x 36 all the   way through.  It fits OK on 3/4" round shaft for welding, even though   it has interior splines. 
Coupler = 2" L x 1.060" D 
                                                    

						                        

							                        

                                                        
Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing.
Full compliment bearings
Forged Vanadium steel yokes and u-joint
Highest quality for racing or street
Features needle bearing u-joints 
13/16"-36 Spline
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:    GM columns measure slightly less than 1"   while IDIDIT and Flaming    River columns measure a true 1".  DO NOT   interchange these u-joints. 
                                                    

						                        

							                        

                                                        
Don't jeopardize your safety with inferior quality steering  components. Speedway offers only the finest steering U-joints available.  Made by Sweet Manufacturing.
Full compliment bearings
Forged Vanadium steel yokes and u-joint
Highest quality for racing or street
Features needle bearing u-joints 
13/16"-36 Spline
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:     GM columns measure slightly less than 1"   while IDIDIT and Flaming     River columns measure a true 1".  DO NOT   interchange these  u-joints. 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. Made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.
Spline Size (Link)
Steering Box/Rack/Spline Chart (Link)
Note:  GM columns measure slightly less than 1"   while IDIDIT and Flaming  River columns measure a true 1".  DO NOT   interchange these u-joints. 
 
                                                    

						                        

							                        

                                                        
These polished stainless steel steering U-joints look & function  beautifully and use non-pinch bolts which will need to be either welded,  cross-drilled and pinned or bolted. 
The OD is 1.650" (41.90mm)  
 3-3/4" in total length
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
                                                    

						                        

							                        

                                                        
Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. They feature a double D end to make use of the double D shaft.
Full compliment bearings
Forged Vanadium steel yokes and u-joint
Highest quality for racing or street
Features needle bearing u-joints
13/16"-36 Spline
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:    GM columns measure slightly less than 1"   while IDIDIT and Flaming    River columns measure a true 1".  DO NOT   interchange these u-joints. 
                                                    

						                        

							                        

                                                        
We now offer ¾” DD shaft machined the entire length of the shaft, making it easier to set up your steering. Carbon steel shaft comes in 22".