Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf

Sweet Mfg Steering U-Joint, 1 Inch DD to 1 Inch DD, IDIDIT/Flaming River Column

SAME DAY SHIPPING! Most orders ship within 24 hours.

Specs
Material Type:
Steel
Sold in Quantity:
Each
Finish:
Black Oxide
End #1:
1 inch DD
End #2:
1 inch DD
MFG. Part #:
401-52323
Set Screw Included:
No
Max Operating Angle:
30
Sweet Mfg Steering U-Joint, 1 Inch DD to 1 Inch DD, IDIDIT/Flaming River Column
Sweet Mfg Steering U-Joint, 1 Inch DD to 1 Inch DD, IDIDIT/Flaming River Column

Click image to enlarge

Speeday Motors Logo
X
Sweet Mfg Steering U-Joint, 1 Inch DD to 1 Inch DD, IDIDIT/Flaming River Column

Details

Reviews

Q & A

What's in the Box

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are of the highest quality for racing and street use.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Application

When purchasing U-Joints, 3 easy steps will help ensure that they will be correct for your application.

STEP 1
Be sure to measure the diameter of the shaft and count the number of splines on the shaft. Some shafts have a blank spot ground on one side. To get the correct number of splines, use a flat edge and cover the blank half of the shaft through the diameter and count the splines on the other half. Multiply that number by 2, thus giving you the total number of splines on the full circumference of the shaft.

STEP 2

Choose which shaft type best suits your application: 3/4" weld on, 3/4" DD or 1" DD.

STEP 3
With these two pieces of information at hand, refer to our chart to find the appropriate part number of the ujoint for your specific application.

Notes

Tech Tip #1: When using more than two universal joints in a system, a support heim must be used.

Tech Tip #2: Increasing a U-Joint's angle of operation beyond 30° dramatically increases the stress on the joint, weakening the whole steering mechanism. If a greater angle is needed, add another u-joint.

Item Details

GM columns measure slightly less than 1" while Ididit and Flaming River columns measure a true 1".

You may also be interested in:

Sweet Mfg Steering U-Joint, 1 Inch DD, 3/4 Round, IDIDIT/Flaming River Column
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have a 3/4" round weld-on end.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg Steering U-Joint, 1 Inch DD to 3/4 DD, IDIDIT/Flaming River Column
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing.

These steering universal joints are CNC machined from aircraft steel to precision tolerances. The sealed needle bearing design will last ten times longer than a standard pin and block universal joint. The unique nickel plating prevents rust without the hassle of painting.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 DD, IDIDIT/Flaming River
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg. Double Steering U-Joint, 1 DD to 3/4 Round, IDIDIT/Flaming River
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

  • Overall length is 5-1/2”
  • O.D. at ends is 1.12”
  • O.D. in the middle is 1.476”
  • O.D. at caps is 1.350”
  • O.D. at cap retainer screws is 1.545”
  • Length of center section is 2-3/4”
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Unisteer 8050310 Steering U-Joint-1 Inch Double D to 3/4 Inch Double D
                        

These polished stainless steel U-joints look great and use a pinch bolt on each end for easy installation.

This is a size that is used on some large GM steering columns. This specific steering universal joint uses a pinch bolt fastener on the 3/4"DD side and a set screw on the 1"DD side, due to the large size

Steering U-Joints and Couplers Application Chart (GIF)

Steering Box/Rack/Spline Chart (Link)

Spline Size (Link)

NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

Fits IDIDIT/Flaming River 1" Double D

Sweet Mfg Chrome Steering U-Joint, 1 DD to 3/4 DD, Ididit/Flaming River Column
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg Chrome Steering U-Joint, 1 Inch DD, Ididit/Flaming River Column
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Speedway 3/4 OD Steel Weld-On Double-D Steering Shaft, 36 Inch Length
                        

This steering shaft is 3/4" O.D DD. This steering shaft also has a 1.00" long "D" design on each end.

This steering shaft entails:

  • 1018 Steel
  • Weld on
  • Excellent for steering shafts or other uses 
  • Order desired length

 

NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

Steel Heim Joint Rod Ends for Steering Shaft, 3/4-16 RH Male .757 Hole
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.


Firewall Mount Steering Flange Sleeve, 1 Inch Shaft
                        This firewall mount allows up to 30° of mis-alignment. Includes ball with two pressed steel flanges with 5/16" square mounting holes. 

Choose 3/4" (750) or 1" (1000) shaft size.

91032375-1000

  • Height: .74"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
91032375-750
  • Height: .87"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"