ALWAYS SECURE
America's Oldest Speed Shop ® 800.979.0122 Lincoln, NE
Filters
Menu
Help Center
Help Center
x
x
Help Center

sales@speedwaymotors.com

Contact
Help Center
x
x
How to Contact Us

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
x

Sweet Mfg. Steering U-Joint, 1 Inch-48 Spline to 3/4 Inch DD, GM Column

SAME DAY SHIPPING! Order within the next 6 hours 16 minutes and receive same day shipping

Specs
Material Type:
Steel
Sold in Quantity:
Each
Finish:
Black Oxide
End #1:
3/4 inch DD
Spline Count:
48
MFG. Part #:
401-51819
Set Screw Included:
Yes
Max Operating Angle:
30
Sweet Mfg. Steering U-Joint, 1 Inch-48 Spline to 3/4 Inch DD, GM Column

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 1"-48 spline.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 1"-48 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Application

When purchasing U-Joints, 3 easy steps will help ensure that they will be correct for your application.

STEP 1
Be sure to measure the diameter of the shaft and count the number of splines on the shaft. Some shafts have a blank spot ground on one side. To get the correct number of splines, use a flat edge and cover the blank half of the shaft through the diameter and count the splines on the other half. Multiply that number by 2, thus giving you the total number of splines on the full circumference of the shaft.

STEP 2

Choose which shaft type best suits your application: 3/4" weld on, 3/4" DD or 1" DD.

STEP 3
With these two pieces of information at hand, refer to our chart to find the appropriate part number of the ujoint for your specific application.

Notes

Tech Tip #1: When using more than two universal joints in a system, a support heim must be used.

Tech Tip #2: Increasing a U-Joint's angle of operation beyond 30° dramatically increases the stress on the joint, weakening the whole steering mechanism. If a greater angle is needed, add another u-joint.

Item Details

GM Column
1"-48 Spline

Customer Reviews

Rated 5 out of 5 by 3 reviewers.
RATING BREAKDOWN
3 reviews
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
RECOMMEND THIS PRODUCT:

OkcLarryD
Verified Purchaser
Okc, OK

Excellent Piece

April 12, 2015
High quality, nice finish, and it fit!! Just like most Speedway products, it was what I asked for. Sorry for your loss. He was a true pioneer.
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

RandBcustom
Verified Purchaser
Nixa MO

Perfect fit

August 31, 2014
Perfect fit, high quality item. Works right out of the box, no modifications.
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

T-Bucket Jim
Verified Purchaser
Denver CO

heavy duty

June 04, 2012
Fit perfect
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Page 1 of 1

Product Q&A

1 questions : 1 answers

1 answers

what is the overall length?

ray
April 19, 2015

what is the overall length?

Answers

April 20, 2015
Eric
Expert
The overall length of this U-joint is 3 3/4"
Page 1 of 1

You may also be interested in:

Sweet Mfg. Steering U-Joint, 1 Inch 48-Spline to 1 Inch DD, GM Column
(Part #91032397)
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 1"-48 spline.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 1"-48 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg. Double U-Joint, 1 In-48 Spline to 3/4 In Round, GM Column
(Part #9103220)
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

  • Overall length is 5-1/2”
  • O.D. at ends is 1.12”
  • O.D. in the middle is 1.476”
  • O.D. at caps is 1.350”
  • O.D. at cap retainer screws is 1.545”
  • Length of center section is 2-3/4”
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

 

Sweet Mfg. Double U-Joint, 1 In 48-Spline to 3/4 In DD, GM Column
(Part #9103240)
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Steel Heim Joint Rod Ends for Steering Shaft, 3/4-16 RH Male .757 Hole
(Part #1750757)
                        3/4" heim for steering shaft support.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.


Firewall Mount Steering Flange Sleeve, 3/4 Inch Shaft
(Part #91032375-750)
                        This firewall mount allows up to 30° of mis-alignment. Includes ball with two pressed steel flanges with 5/16" mounting holes. 

Choose 3/4" (750) or 1" (1000) shaft size.

91032375-1000

  • Height: .74"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
91032375-750
  • Height: .87"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
Speedway 3/4 OD Steel Weld-On Double-D Steering Shaft, 12 Inch Length
(Part #91032386-12)
                        

This steering shaft is 3/4" O.D DD. This steering shaft also has a 1.00" long "D" design on each end.

This steering shaft entails:

  • 1018 Steel
  • Weld on
  • Excellent for steering shafts or other uses 
  • Order desired length

NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.