Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf

Sweet Mfg. Double Steering U-Joint, 3/4 In DD to 3/4 In DD, Universal

SAME DAY SHIPPING! Order within the next 11 hours 45 minutes and receive same day shipping

Specs
Material Type:
Steel
Overall Length:
6.625
Sold in Quantity:
Each
Finish:
Black Oxide
Outside Diameter:
1.500
End #1:
3/4 inch DD
End #2:
3/4 inch DD
MFG. Part #:
401-81919
Set Screw Included:
Yes
Max Operating Angle:
70
Sweet Mfg. Double Steering U-Joint, 3/4 In DD to 3/4 In DD, Universal
Sweet Mfg. Double Steering U-Joint, 3/4 In DD to 3/4 In DD, Universal

Click image to enlarge

Speeday Motors Logo
X
Sweet Mfg. Double Steering U-Joint, 3/4 In DD to 3/4 In DD, Universal

Details

Reviews

Q & A

What's in the Box

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

You may also be interested in:

Sweet Mfg Steering U-Joint, 3/4 In Round to 3/4 In Round, Universal
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering u-joints available. Made by Sweet Manufacturing. These steering universal joints have 3/4 weld-on ends.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing
  • Features needle bearing u-joints
  • U-Joint=3.875" L x 1.375" D

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

 

Sweet Mfg Steering U-Joint, 3/4 Inch DD to 3/4 Inch DD, Universal
                        Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. This universal joint is 3.875 inches long and 1.375 inches in diameter.
  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing
  • Features needle bearing u-joints
  • U-Joint=3.875" L x 1.375" D
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg U-Joint, 3/4 In Round to 1 In DD, GM Column/Universal
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have a 3/4 round weld-on end.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing
  • Features needle bearing u-joints
  • U-Joint=3.875" L x 1.375" D
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg. Double U-Joint, 1 In-48 Spline to 3/4 In Round, GM Column
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

  • Overall length is 5-1/2”
  • O.D. at ends is 1.12”
  • O.D. in the middle is 1.476”
  • O.D. at caps is 1.350”
  • O.D. at cap retainer screws is 1.545”
  • Length of center section is 2-3/4”
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

 

Sweet Mfg. Double Steering U-Joint, 3/4 Round to 3/4 Round, Universal
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.
Steering Shaft, 3/4 Inch O.D. Double D, 4-16 Inch Lengths, Steel
                        

This steering shaft is 3/4" O.D DD. This steering shaft also has a 1.00" long "D" design on each end.

This steering shaft entails:

  • 1018 Steel
  • Weld on
  • Excellent for steering shafts or other uses 
  • Order desired length

NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

3/4 O.D. Solid Steel Steering Shaft
                        

Speedways steering shaft is made for you to cut-to-fit. This steering shaft entails:

  •  3/4" O.D.
  • 1018 solid steel steering shaft
  • Available in 24", 36", 48", 60" and 72" lengths

 

Steer Shaft Application Chart

Sweet Mfg. Double U-Joint, 3/4 In Round to 3/4 In DD, Universal
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. Made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Unisteer 8050420 Steering U-Joint, 3/4 Inch Smooth to 3/4 Inch Smooth
                        

These polished stainless steel U-joints look & function beautifully and use non-pinch bolts which will need to be either welded, cross-drilled and pinned or bolted. These steering universal joints are 3-3/4 inch in total length and have a 1.650 inch diameter.

  • The OD is 1.650" (41.90mm) 
  • 3-3/4" in total length
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.
Unisteer 8050300 Steering U-Joint, 3/4 Inch Double D to 3/4 Inch DD
                        

These polished stainless steel steering U-joints look great and use a pinch bolt on each end for easy installation.

This particular steering universal joint is made to fit 3/4"DD shafting on both sides. Both sides incorporate the pinch bolt design.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

Polished Stainless Steel 3/4 O.D. Double D Shaft
                        

Steering shafts that are just plain looking look kind of silly with those shiny stainless steel U-joints. Our polished, stainless steel, double D steering shaft would be more compatible. We offer steering shafts in 18", 22", and 36" cut to fit lengths.

 

Unisteer 8050230 Steering U-Joint, 9/16 Inch-26 Spline to 3/4 Inch DD
                        

These polished stainless steel U-joints look great and use a pinch bolt on each end for easy installation. These universal joints are 3-3/4 inch in length and have a 1.650 inch outside diameter.

  • The OD is 1.650" (41.90mm) 
  • 3-3/4" in total length

This size of spline works with Unisteer's Cross Steer Rack & Pinion, Prostock Rack, and Manual Camaro Rack & Pinion and is also the size of manual Mustang Style Rack & Pinions.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

NOTE:  These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.

Sweet Mfg. 401-91919 Chrome Double U-Joint, 3/4 Inch DD to 3/4 Inch DD
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.

  • These are 5-5/8" Long
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Steering Shaft, Fully Machined Double D Shaft, Raw 22 Inch
                        

 Speedway now offers a steering shaft that is 3/4" DD machined the entire length of the shaft. This makes it easier to set up your steering. The carbon steel steering shaft come in 22".