Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf

Sweet Mfg Chrome Steering U-Joint, 1In-48 Spline to 1 In DD, GM Column

SAME DAY SHIPPING! Order within the next 1 hour 33 minutes and receive same day shipping

Specs
Material Type:
Steel
Sold in Quantity:
Each
Finish:
Chrome
End #1:
1 inch DD
End #2:
1"-48 spline
Spline OD:
1.00
Spline Count:
48
MFG. Part #:
401-61820
Set Screw Included:
Yes
Max Operating Angle:
30
Sweet Mfg Chrome Steering U-Joint, 1In-48 Spline to 1 In DD, GM Column
Sweet Mfg Chrome Steering U-Joint, 1In-48 Spline to 1 In DD, GM Column

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 1" DD
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Application

When purchasing U-Joints, 3 easy steps will help ensure that they will be correct for your application.

STEP 1
Be sure to measure the diameter of the shaft and count the number of splines on the shaft. Some shafts have a blank spot ground on one side. To get the correct number of splines, use a flat edge and cover the blank half of the shaft through the diameter and count the splines on the other half. Multiply that number by 2, thus giving you the total number of splines on the full circumference of the shaft.

STEP 2

Choose which shaft type best suits your application: 3/4" weld on, 3/4" DD or 1" DD.

STEP 3
With these two pieces of information at hand, refer to our chart to find the appropriate part number of the ujoint for your specific application.

Notes

Tech Tip #1: When using more than two universal joints in a system, a support heim must be used.

Tech Tip #2: Increasing a U-Joint's angle of operation beyond 30° dramatically increases the stress on the joint, weakening the whole steering mechanism. If a greater angle is needed, add another u-joint.

Item Details

1"-48 Spline to 1" Double D
GM Column

You may also be interested in:

U-Joint, 1"-48 Spline To 3/4" DD
SKU-91032297
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 1"-48 spline.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 1"-48 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg. Steering U-Joint, 1 Inch 48-Spline to 1 Inch DD, GM Column
SKU-91032397
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are 1"-48 spline.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 1"-48 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg. Double Steering U-Joint, 1 Inch DD to 3/4 Inch Round
SKU-9103230
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Sweet Mfg. Double Steering U-Joint, 1 In DD to 3/4 In DD, GM Column
SKU-9103250
                        

Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. These steering universal joints are made of forged vanadium steel and real needle bearing joints.  5-5/8" overall length.

Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Steering Shaft Aluminum Heim Joint Rod Ends, 3/4-16 RH Male, .757 Hole
SKU-1750759
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.
                    
Sweet Mfg Chrome Steering U-Joint, 1 In-48 Spline to 3/4 DD, GM Column
SKU-9106181
                        

Don't jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints feature a double D end to make use of the double D shaft.

  • Full compliment bearings
  • Forged Vanadium steel yokes and u-joint
  • Highest quality for racing or street
  • Features needle bearing u-joints
  • 1" DD
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.

Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1".  DO NOT interchange these u-joints.

Flat Heim Joint Rod End Support Bracket
SKU-91000256
                        Overall length of 3 1/2 inches long.  Offered with a 3/4 clearances hole for steering heim with a slotted adjustment of 1 7/8 inch long. Bracket is 3/16 thick steel.
                    
Steel Heim Joint Rod Ends for Steering Shaft, 3/4-16 RH Male .757 Hole
SKU-1750757
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.


Speedway 3/4 OD Steel Weld-On Double-D Steering Shaft, 36 Inch Length
SKU-91032387-36
                        

This steering shaft is 3/4" O.D DD. This steering shaft also has a 1.00" long "D" design on each end.

This steering shaft entails:

  • 1018 Steel
  • Weld on
  • Excellent for steering shafts or other uses 
  • Order desired length

 

NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

Firewall Mount Steering Flange Sleeve, 1 Inch Shaft
SKU-91032375-1000
                        This firewall mount allows up to 30° of mis-alignment. Includes ball with two pressed steel flanges with 5/16" square mounting holes. 

Choose 3/4" (750) or 1" (1000) shaft size.

91032375-1000

  • Height: .74"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
91032375-750
  • Height: .87"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"