Sweet Mfg Chrome Double U-Joint, 3/4 Inch DD to 1 Inch DD, IDIDIT/Flaming River

							                        

                                                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.
                                                    
						                        

							                        

                                                        
These polished stainless steel U-joints look great and use a pinch bolt on each end for easy installation.
This is a size that is used on some large GM steering columns. This  specific U-Joint uses a pinch bolt fastener on the 3/4"DD side and a set  screw on the 1"DD side, due to the large size 
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
NOTE:  These  u-joints contain a safety feature that requires the DD steering shaft  to be notched for pinch bolt clearance. Once notched, the pinch bolt  MUST be torqued to 45 ft/lbs to ensure a tight fit.
Fits IDIDIT/Flaming River 1" Double D 
                                                    

						                        

							                        

                                                        
Don't jeopardize your safety with inferior quality steering  components. Speedway offers only the finest steering U-joints available.  Made by Sweet Manufacturing. They feature a double D end to make use of  the double D shaft.
Full compliment bearings
Forged Vanadium steel yokes and u-joint
Highest quality for racing
Features needle bearing u-joints 
1.354" not including the screws (1.534" including), width on the u-joint.
1.125" OD on the ends not including the nut (1.345" including the nut).  
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:     GM columns measure slightly less than 1"   while IDIDIT and Flaming     River columns measure a true 1".  DO NOT   interchange these  u-joints. 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard steering u-joint can give you. Our double u-joints allow up to 70 degrees of angle or 1" of offset for just those occasions. Made of forged vanadium steel and real needle bearing joints.
These are 5-3/4" Long 
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:    GM columns measure slightly less than 1"   while IDIDIT and Flaming    River columns measure a true 1".  DO NOT   interchange these u-joints. 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard  steering u-joint can give you. Our double u-joints allow up to 70  degrees of angle or 1" of offset for just those occasions. Made of  forged vanadium steel and real needle bearing joints.
These are 5-5/8" Long 
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:     GM columns measure slightly less than 1"   while IDIDIT and Flaming     River columns measure a true 1".  DO NOT   interchange these  u-joints. 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard  steering u-joint can give you. Our double u-joints allow up to 70  degrees of angle or 1" of offset for just those occasions. Made of  forged vanadium steel and real needle bearing joints.
These are 5-3/4" Long 
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:     GM columns measure slightly less than 1"   while IDIDIT and Flaming     River columns measure a true 1".  DO NOT   interchange these  u-joints. 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard  steering u-joint can give you. Our double u-joints allow up to 70  degrees of angle or 1" of offset for just those occasions. Made of  forged vanadium steel and real needle bearing joints.
These are 5-3/4" Long 
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:     GM columns measure slightly less than 1"   while IDIDIT and Flaming     River columns measure a true 1".  DO NOT   interchange these  u-joints. 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard  steering u-joint can give you. Our double u-joints allow up to 70  degrees of angle or 1" of offset for just those occasions. Made of  forged vanadium steel and real needle bearing joints.
These are 5-3/4" Long 
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:     GM columns measure slightly less than 1"   while IDIDIT and Flaming     River columns measure a true 1".  DO NOT   interchange these  u-joints. 
                                                    

						                        

							                        

                                                        
Sometimes you need just a little bit more clearance than a standard  steering u-joint can give you. Our double u-joints allow up to 70  degrees of angle or 1" of offset for just those occasions. Made of  forged vanadium steel and real needle bearing joints.
These are 5-3/4" Long 
Steering U-Joints and Couplers Application Chart (GIF) 
Steering Box/Rack/Spline Chart (Link)
Spline Size (Link) 
Note:     GM columns measure slightly less than 1"   while IDIDIT and Flaming     River columns measure a true 1".  DO NOT   interchange these  u-joints. 
                                                    

						                        

							                        

                                                        Overall length of 3 1/2 inches long.  Offered with a 3/4 clearances hole for steering heim with a slotted adjustment of 1 7/8 inch long. Bracket is 3/16 thick steel.