Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith

Steel Heim Joint Rod Ends for Steering Shaft, 3/4-16 RH Male .757 Hole

SAME DAY SHIPPING!

Specs
Material Type:
Steel
Overall Width:
1.76
Overall Length:
3.75
Sold in Quantity:
Each
Finish:
Zinc
Inside Diameter:
.76
Thread Length:
1.75
Thread Pitch:
3/4"-16
Center Hole to End of Shank:
2.88
Threads:
RH Male
Garage Sale:
No
Ball Thickness:
.88

Share by Email

From
To

Click image to enlarge

X

Details

Reviews

Q & A

What's in the Box

3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.


Item Details

.757" Ball Hole

You may also be interested in:

Steel Double D Shaft, 3/4 Inch O.D., 4 - 16 Inch Lengths
                        

This 3/4" O.D. DD shaft has a 1.00" long "D" design on each end. Made from 1018 steel, weld-on. Excellent for steering shafts or other uses. Order desired length. 

NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

Steel Double D Shaft, 3/4 Inch O.D., 18 - 36 Inch Lengths
                        

This 3/4" O.D. DD shaft has a 1.00" long "D" design on each end. Made from 1018 steel, weld-on. Excellent for steering shafts or other uses. Order desired length. 

NOTE: This DD shaft is only milled with flats on both ends for 1" of length of the shaft. It is not milled the entire length of the shaft and therefore, can not be cut to length unless it is going to be welded to a 3/4" round or has new flats milled into the end. Please see Flaming River DD shaft if fully machined DD shaft is required.

Hollow Steering Shaft
                        

Hollow steering shafts for you to cut to fit. 3/4" DOM .120 wall hollow steering shaft. Available in 24", 36", 48", 60" and 72" lengths.

3/4 O.D. Solid Steel Steering Shaft
                        These solid steering shafts are made for you to cut to fit. 3/4" O.D. 1018 solid steel shaft. Available in 24", 36", 48", 60" and 72" lengths. 

Steer Shaft Application Chart

Steering Shaft Aluminum Heim Joint Rod Ends, 3/4-16 RH Male, .757 Hole
                        3/4" heim for steering shaft.  Has .757 ball hole. Slides right over standard 3/4" steering shaft. 3/4" NF right hand threads. Jam nut sold separately.
                    
Speedway Fully Machined Double D Shaft, Raw 22 Inch
                        

We now offer ¾” DD shaft machined the entire length of the shaft, making it easier to set up your steering. Carbon steel shaft comes in 22".

Speedway Fully Machined Double D Shaft, Raw 36 Inch
                        We now offer ¾” DD shaft machined the entire length of the shaft, making  it easier to set up your steering.  Carbon steel shaft comes in   36”.
                    
Flat Heim Joint Rod End Support Bracket
                        Overall length of 3 1/2 inches long.  Offered with a 3/4 clearances hole for steering heim with a slotted adjustment of 1 7/8 inch long. Bracket is 3/16 thick steel.
                    
Angled Heim Joint Rod End Support Bracket
                        Over all length of 3 1/2 inches long. Offered with a 3/4" clearance hole for steering heim with a slotted adjustment of 1 7/8 inch long angled at a 45 degrees.  Bracket is 3/16 thick steel
                    
Speedway Fully Machined Double D Shaft, Raw, 18 Inch
                        We now offer ¾” DD steering shaft machined the entire length of the shaft, making  it easier to set up your steering. This carbon steel double D shaft comes in 18" lengths.
                    
Thin Steel Jam Nut, 3/4-16 RH
                        

Plain steel fine thread jam nut. Special half thickness nuts for securing steering heims to a panel or flange.

Firewall Mount Flanged Bearing for Steering Shaft
                        This firewall mount allows up to 30° of mis-alignment. Includes ball with two pressed steel flanges with 5/16" square mounting holes. 

Choose 3/4" (750) or 1" (1000) shaft size.

91032375-1000

  • Height: .74"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
91032375-750
  • Height: .87"
  • Length: 3.00"
  • Width: 1.90"
  • Mount C to C: 2.26"
Pro-Blend 1720 Anti-Seize Compound
                        

Apply Pro-Blend anti-seize directly to any metal surface that may gall or seize due to heat, pressure, torque loading or shock. Excellent in environments of gas, alcohol, water, solvents, dirt, sand, and grit.

  • Defies contact of dissimilar or like metals
  • Not affected by heat, moisture, salt water, or corrosion

Learn why using anti-seize is so important in our tech article, Installing New Hardware.