ALWAYS SECURE
America's Oldest Speed Shop ® 800.979.0122 Lincoln, NE
Filters
Menu
Contact
Help Center
x
x
How to Contact Us

U.S.Order Line:

800.979.0122

(CST) 7am - 10pm

Race and Rod Tech Support

Mon-Fri 8am - 5pm

Canadian Order Line:

855.313.9180

International Order Line:

1.402.323.3200
Since 1952
Menu
x

Speedway Throttle Assembly

SAME DAY SHIPPING! Order within the next 55 minutes and receive same day shipping

Specs
Material Type:
Aluminum
Overall Height:
7.50
Overall Width:
3.00
Overall Length:
6.00
Color:
Silver
Sold in Quantity:
Kit
Finish:
Natural
Hole Diameter:
29
Cable length:
48
Pedal Length:
8.50
MFG. Part #:
720-4103
Garage Sale:
No
Pedal Width:
2.50
Notes
Mounting base is 2.5" x 6" x 1/4" thick. Pedal rests at 45 degree angle to base. Has 2" travel.
Speedway Throttle Assembly
Speedway Throttle Assembly
Speedway Throttle Assembly

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

Full cam-slot cable action throttle assembly. Cast aluminum base and textured pedal. Assembly includes heavy duty 48" cable and housing clamp.

Notes

Cable Installation:

  1. Remove the throttle pedal rod.
  2. Place "looped" end of supplied cable between the nylon bushing and washer.
  3. Clamp cable on pedal assembly with the through-bolt hole.
  4. The other end of the cable has a small insert that can be used on a carb linkage rod and clamps the cable in place.

Specs


Customer Reviews

Rated 4.1 out of 5 by 16 reviewers.
RATING BREAKDOWN
16 reviews
5 Stars
8
4 Stars
4
3 Stars
3
2 Stars
0
1 Star
1
RECOMMEND THIS PRODUCT:

buford
Verified Purchaser
wheatland wy

i would buy this product again

June 12, 2015
I am using this pedal on a v8 trike
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

shiftkit
Brighton, IL 62012, USA

works good but could easily made to be R

September 26, 2014
How the cable is held is the only downfall. They need to have a round cap with a hole in it for the cable housing to slide into so you don't have to clamp it so hard. The harder you tighten it the stiff the throttle operates and if it could be made to get a little more travel so you get wide open throttle would be nice. It's close but not quite enough & if you relocate the pull point on the carb, You will break the cable when you step on the throttle. Don't ask How I know that one! LOL
No, I would not recommend this product.
Full Size Image

Was this review helpful? 0 0

elcomeano
Verified Purchaser
NW ohio

could be better

May 04, 2014
The peddle itself is great.... the cable assembly isn't all that good... After modifying the peddle I installed a LOKAR cable... now it works great
Pros:
  • great peddle
Cons:
  • cable not great
No, I would not recommend this product.
Full Size Image

Was this review helpful? 0 0

Joecool3
Verified Purchaser
Independence, MO, USA

This product was easy to install

March 29, 2014
I needed a throttle assembly for my 1961 Comet Gasser, looked at several. this one filled the bill very well.
Pros:
  • Works well
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

AR75
Verified Purchaser
Camarillo, CA, USA

used this before on the V8 conversions I

January 12, 2013
very easy to install, fabricate a few brackets and it all hooks up!
Pros:
  • Excellent product
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Brent
Verified Purchaser
Dover, DE

I would buy this product again.

August 19, 2012
This product fit my needs perfectly. Was easy to install and works great. The only thing I would recommend is a beefier cable clamp than what was supplied.
Pros:
  • Easy To Use
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Rick
Verified Purchaser
Lenoir North Carolina

works great on my show yard tractor

July 28, 2012
I have a yard Tractor that I show and I thought it would work great on my tractor and look great on it to have a gas pedal
Pros:
  • Quality Construction
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Rick
Verified Purchaser
Lenoir North Carolina

works great on my show yard tractor

July 28, 2012
I have a yard Tractor that I show and I thought it would work great on my tractor and look great on it to have a gas pedal
Pros:
  • Quality Construction
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Goldie
Verified Purchaser
Hutto Texas

Not enough travel

April 12, 2012
Not enough travel and clamps did not hold cable tight. Also plastic grommet cheap but for price what do you expect, ended up giving to a friend hope he has better luck.
No, I would not recommend this product.
Full Size Image

Was this review helpful? 0 0

George
Verified Purchaser
PA

i WOULD BUY THIS PRODUCT AGAIN

March 16, 2012
WORKED AS STATED
Pros:
  • Easy To Use
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Page 1 of 2

Product Q&A

1 questions : 1 answers

1 answers

What's the screw post for? Purchased this pedal for my roadster project, but there were no directions or schematics included. The "directions" on your website are vague at best and it would be helpful to see a picture, or drawing, of the pedal installed.

doktagil
Loveland, CO, USA
March 23, 2015

What's the screw post for? Purchased this pedal for my roadster project, but there were no directions or schematics included. The "directions" on your website are vague at best and it would be helpful to see a picture, or drawing, of the pedal installed.

Answers

March 24, 2015
EricM
The post with the bolt is a throttle stop. It allows you to have a positive stop on the pedal assembly instead of putting stress on the cable and carburetor linkage. Sorry for the limited installation tips on this item. This is somewhat of a builders type of item and does take some imagination for installing it. Each installation will vary but as long as you have the cable mounted so that the pedal pulls on it in a straight line then the pedal will work great for you.
Page 1 of 1

You may also be interested in:

Lokar FMG-6098 Eliminator Floor Mount Throttle Pedal, Billet Alum
(Part #4916098)
                        

Recipient of NSRA best new product, Lokar's Eliminator Floor Mount Throttle Pedal is designed with the Signature Lokar Quality you have come to expect.  Pedal eliminates routing cables through firewall and comes equipped with a billet aluminum splined adjustable shaft and stainless steel "under-the-floor" cable mounting bracket.  Mounts in multiple positions for floor and toe board angles.  Designed with built-in pedal travel stops.   Requires 36" "U-Cut-to-Fit" Lokar Throttle Cable for most applications.  Order 48" cable for LS1, Ramjet and Vortec applications.

  • Comes equipped with a billet aluminum splined adjustable shaft and stainless steel "under-the-floor" cable mounting bracket 
  • Mounts in multiple positions for floor and toe board angles
  • Designed with built-in pedal travel stops
  • Requires 36" "U-Cut-to-Fit" Lokar Throttle Cable for most applications
  • Pedal pad is 2” by 6-3/4”
  • Pad is parallelogram in shape and NOT rectangle
  • Brushed billet aluminum finish

Eliminator Throttle Pedal Installation Instructions (PDF)

 

Offenhauser 6244 Aluminum Throttle Pedal
(Part #5606244)
                        

Universal cast aluminum pedals are fully adjustable and have a 6-7/8" arm. Throttle cables not included. We recommend universal cable linkage #560-6230.

Cable clamp sleeve is included for attachment to the throttle cable.

  • Mounting base is 5-1/16” tall, 1-1/8” wide, and ¼” thick with 3 mounting hole options
  • Mounting surface to center of pivot point is ½”
  • Upper arm pivot hole to center of cable attachment hole is 3¼”
  • Lower pedal arm is 8-1/8” from pivot point center to end of arm and has 4 mount holes for the pedal pad
  • Pedal pad has non slip diamond pattern and at bottom hole on arm extends past arm 1”
  • Pedal pad is 1-1/8” wide, 2-5/8” tall, and ¼” thick
  • Lower arm has 4 mount holes to change angle with the upper arm

Item Details

Includes Offy logo on pedal pad.
Big Foot Floor Mount Throttle Pedal
(Part #7204107)
                        Heavy duty construction. With mount and return spring. This pedal is designed to work with a mechanical throttle linkage. However, the pedal may be modified by the installer to make use of a throttle cable if needed.
                    
Barefoot Gas Pedal Cover
(Part #7208520)
                        A footprint gas pedal chrome detail for your project. Mounts over your original pedal using included bracket.
                    
Speedway Carburetor Bracket and Throttle Return Springs
(Part #4914000)
                        Stainless throttle cable bracket & spring set. Mounts to rear of Holley, Edelbrock, AFB, Quadrajet, Demon, and in-line dual quad carburetors. Dual spring design provides a safe, reliable throttle return when compared to single spring set-ups.

Note: There is no provision in this bracket for an automatic transmission.
Lokar XFMG-6098 Billet Aluminum Eliminator Floor Mount Throttle Pedal
(Part #49106098)
                        

Recipient of NSRA best new product, Lokar's Eliminator Floor Mount Throttle Pedal is designed with the Signature Lokar Quality you have come to expect. Pedal eliminates routing cables through firewall and comes equipped with a billet aluminum splined adjustable shaft and stainless steel "under-the-floor" cable mounting bracket. Mounts in multiple positions for floor and toe board angles. Designed with built-in pedal travel stops. Requires 36" "U-Cut-to-Fit" Lokar Throttle Cable for most applications.  Use 48" cable for LS1, Ramjet and Vortec applications.

  • Comes equipped with a billet aluminum splined adjustable shaft and stainless steel "under-the-floor" cable mounting bracket 
  • Mounts in multiple positions for floor and toe board angles
  • Designed with built-in pedal travel stops
  • Requires 36" "U-Cut-to-Fit" Lokar Throttle Cable for most applications
  • Black finish

Eliminator Throttle Pedal Installation Instructions (PDF)

Lokar FMG-6097 Eliminator Floor Mount Throttle Pedal, Billet Alum
(Part #4916097)
                        

Recipient of NSRA best new product, Lokar's Eliminator Throttle Floor Mount Pedal is designed with the signature Lokar quality you have come to expect. Pedal eliminates routing cables through firewall and comes equipped with a billet aluminum splined adjustable shaft and stainless steel "under-the-floor" cable mounting bracket. Mounts in multiple positions for floor and toe board angles. Designed with built-in pedal travel stops.

  • Recipient of NSRA best new product
  • Eliminates routing cables through firewall
  • Billet aluminum splined adjustable shaft
  • Stainless steel "under-the-floor" cable mounting bracket
  • Mounts in multiple positions
  • Built-in pedal travel stops

Note: These throttle pedals require 36" "U-Cut-to-Fit" Lokar Throttle Cable for most applications. Order 48" cable for LS1 Ramjet and Vortec applications.

Lokar S-1034 Carb End Assembly for Lokar Throttle Cables
(Part #491S1034)
                        Lokar S-1034 Replacement Carb end assembly for Lokar Throttle Cables.