Speedway 1999-2002 LS1 Engine Wiring Harness, Extended

							                        

                                                        You will need the correct throttle cable for your LS1 / 350 Ramjet swap. This cut-to-fit cable looks good and gets the job done.
                                                    
						                        

							                        

                                                        Take advantage of GM's electronic engine management system with this Painless Wiring Harness. Complete stand alone harness allows you to install late model GM fuel injected engine and correct computer into almost any chassis. 

Besides the obvious economy and driveability benefits, check out these other great features that make it easy and painless to install: 
Foolproof factory connections
ALDL (diagnostic) plug
Computer controlled fuel pump provision
GM color code
Closed loop design
Complete information manual
1999-2002 GM LS1 Wiring Instructions (PDF)
                                                    

						                        

							                        

                                                        Take advantage of GM's electronic engine management system with this Painless Wiring Harness. Complete stand alone harness allows you to install late model GM fuel injected engine and correct computer into almost any chassis. 

Besides the obvious economy and driveability benefits, check out these other great features that make it easy and painless to install: 
Foolproof factory connections
ALDL (diagnostic) plug
Computer controlled fuel pump provision
GM color code
Closed loop design
Complete information manual
1999-2002 GM LS1 Wiring Instructions (PDF)
Number of Circuits: 8 Fuses with 2 Ignition & 1 Fuel Pump Relay
Fuse Type: Blade
Firewall Passthrough: Grommet
Color Code Based: 2000 Camaro
Connectors Included: ECM, TPS, IAC, CTS, IAT, MAF, MAP, Injectors, Coils, CMP, CKP, Knock, VSS, Transmission, Front Bank 1 & 2 O2 Sensors
Circuit Designations: Printed Wire Tags on all Connectors and Open Ended Wires
These kits include:
All new fuel injection harness with OEM fitment connectors and harness breakouts
OBDII connector, mounting bracket and check engine light
Harness does not include any emissions related connections
Crimp-on terminals, rubber grommet
Mounting hardware
Installation manual 
                                                    

						                        

							                        

                                                        Clean up your LS1 intake manifold with this billet aluminum cable bracket. Available with a single stud for throttle only or a double stud to add cruise control or kickdown cable. Designed to work with part #491-1000LS1.
                                                    
						                        

							                        

                                                        Clean up your LS1 intake manifold with this billet aluminum cable bracket. Available with a single stud for throttle only or a double stud to add cruise control or kickdown cable. Designed to work with part #491-1000LS1.
                                                    
						                        

							                        

                                                        Clean up your LS1 intake manifold with this billet aluminum cable bracket. Available with a single stud for throttle only or a double stud to add cruise control cable. Designed to work with part #491-1000LS1.
                                                    
						                        

							                        

                                                        Clean up your LS1 intake manifold with this billet aluminum cable bracket. Available with a single stud for throttle only or a double stud to add cruise control cable. Designed to work with part #491-1000LS1.
                                                    
						                        

							                        

                                                        
Take the fear out of electronic fuel injection! These engine wiring harnesses are designed to make your engine transplant effortless. Each new harness contains in-depth application-specific instruction sheets, clearly marked factory GM connectors, labeled GXL jacketed wire, GM color coding, and pre-fitted corrugated slit loom for an extra value and professional look. All un-needed emissions wiring is eliminated to make the install as simple and reliable as possible. Standard length harnesses are 54" from the back of the engine to the PCM connectors. 
1999-2002 LS1 
Made from premium grade GXL jacketed automotive wire
Most wiring is larger gauge than stock application for durability
No splices to reduce points of failure
All   primary grounding is done at the head or block and grounding points  are  isolated from each other to reduce electrical interference and  minimize  ground looping
Harness wiring matches GM wiring configuration and jacket colors follow GM color coding for easy identification
All electrical connectors are made by Delphi or Packard and are direct fit for GM cars and trucks
Can be installed to run engine in 20 minutes, but figure 4-6 hours for a professional installation
Diagnostic connector or OBD2 port for connection to scanners and tuning tools
Made in the USA.
                                                    

						                        

							                        

                                                        You will need the correct throttle cable for your LS1 / 350 Ramjet engine swap. This cut-to-fit cable looks good and gets the job done.
                                                    
						                        

							                        

                                                        
This billet aluminum bracket mounts to the side of the LS1              manifold and is comes with a single stud for throttle only.  
                                                    

						                        

							                        

                                                        
Looking for more shine in your engine compartment?  Try Lokar's Polished  Hi-Tech Throttle Cables.  Lokar's polished cables are available in  stainless steel braided housing or black housing.  They are designed  with a specially extruded liner for extended life of the cable – not to  be confused with ordinary braided brake hose.  Cables are equipped with  polished aluminum fittings and polished aluminum ferrule to eliminate  fraying.  "U-Cut-to-Fit" outer housing is available in 36"  lengths with a "U-Cut-to-Fit" stainless inner wire.  Clevis is designed  without cotter pins or set screws.  Adapts to factory and aftermarket  pedals.            Cables mount nicely with Lokar's array of bracket and return springs (sold separately).  Kits complete with installation  instructions.  Pair up with a polished kickdown.
36" long
GM LS1/Ramjet applications
Specially extruded liner for extended life  of the cable
Aluminum fittings with ferrule to eliminate frayed cable ends
Adaptable for all types of manifolds including tunnel  ram, blower manifolds and Weber induction systems
Complete instructions included
Throttle Body and Carb End Fittings Guide (Link) 
491-001000 Instructions (PDF)
                                                    

						                        

							                        

                                                        Lokar Hi-Tech Throttle Cable features a stainless   steel braided  housing.  They are designed with a specially extruded liner for extended    life of the cable – not to be confused with ordinary braided brake    hose.  Cables are equipped with aluminum fittings and aluminum ferrules    to eliminate fraying.
 Kits come complete  with installation instructions.