Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 50

Products

Tools

Shop Tools At Speedway Motors

The right tools can make any job easier. Whether you are working in the shop, in the pits or on a new engine, Speedway Motors has the tools you need to get the job done quickly and done right.

Featured Products
  • Speedway Air Riveter
    $49.99
    Product Rating: 4.90 Stars
    Speedway Air Riveter
    (Part #91004004)
    x
                Rivet like a pro with this heavy duty air riveter. Allows fast assembly and repair of body panels. Includes nose pieces for 3/16", 5/32", 1/8", and 3/32" pop rivets.
            
  • Cleco Fasteners, Steel, 3/16 Inch, Pack/10
    Cleco Fasteners, Steel, 3/16 Inch, Pack/10
    (Part #91004002)
    x
                

    Cleco pins are a definite must for sheet metal fabrication. They're basically spring-loaded, removable pop rivets that allow you to hold two pieces of sheet metal together in proper alignment for drilling or riveting. They work great for Circle Track use for test-fitting panels before they're permanently attached to your vehicle.

    The pins work with thicknesses of up to 1/4 in.

    Steel Cleco Fasteners

    • 3/16 Inch
    • Pack/10
  • Cam Bearing Driver
    $25.99
    Product Rating: 4.43 Stars
    Cam Bearing Driver
    (Part #91381102)
    x
                Remove and replace your S/B Chevy and 90° V6 cam bearings without damage to the bearings. 

    Note: Always remove cam bearings when boiling or cleaning block.

    913-81102 Instructions (pdf)

  • Edelbrock 4025 Uni-Syn Carburetor Synchronizing Tool
    Edelbrock 4025 Uni-Syn Carburetor Synchronizing Tool
    (Part #3254025)
    x
                

    If you have more than one carb on your hot rod, you need one of these "Uni-Syn" carb synchronizing tools. Just set on the top of your carb and adjust until all the carbs in your tri-power three deuce set-up read the same. 

    Works well on small one barrel and two barrel carbs (downdraft or side-draft). Fits carb necks from 1-3/8" up to 3".

  • AccuAir 3 Gallon Aluminum Tank, Glossy Black Powder Coated Finish
    New
    AccuAir 3 Gallon Aluminum Tank, Glossy Black Powder Coated Finish
    (Part #9109913)
    x
                
    AccuAir 3 Gallon Aluminum Tank is lightweight and corrosion resistant. This aluminum tank is designed for use with Exo Mount system. High quality T.I.G. welds guarantee 100% sealing and a beautiful appearance. Features two built in mounting bosses along the bottom of the tank. Seamless construction allows Exo mount clamping system to fit around the tank at any location.
    • Aluminum construction
    • Glossy black powder coated finish
    • 3 gallon capacity
    • 100% T.I.G. welded
    • Seamless construction
    • Two built in mounting bosses  
    • 1/4" NPT drain port

    Tank Data Sheet (PDF) 

  • Speedway Deluxe Quarter Turn Fastener Tool
    Speedway Deluxe Quarter Turn Fastener Tool
    (Part #91089402)
    x
                

    Stop using a screwdriver...it doesn't fit! This tool makes fast and easy work of removing and attaching panels fastened with 1/4-turn fasteners. Great gift idea!

    Measurement Guide (Link)

  • Small Block Chevy Engine Storage Stand
    Small Block Chevy Engine Storage Stand
    (Part #91681200)
    x
                

    Our handy motor stands allow installation of drives, pulleys and clutches. All four legs fold up for easy storage when stand is not in use. Stand is painted red.

    Note: Engine set up block is shown in photo for reference only and is not provided with the engine stand.

    Fits 1958-Up Small Block Chevy 283-400 engines.

  • MSD 3507 AMP Lug Terminals Crimp Jaws, Fits PN 35051
    MSD 3507 AMP Lug Terminals Crimp Jaws, Fits PN 35051
    (Part #5473507)
    x
                AMP Lug Crimp Jaws allow you to make professional style crimps using PN 35051
    • For use with PN 35051

Filter

"Tools" Page 1 of 50

Page 1 of 50

  • Head Stud Remover and Tap Alignment
    Head Stud Remover and Tap Alignment
    (Part #91081131)
    x
                

    Allows removal of stock press-in studs and aligns the tap (7/16"-14) to simplify the installation of screw in rocker studs.

    For S/B Chevy V8 engines.

  • Speedway Ultrasonic Multi-Purpose Parts Cleaner
    Speedway Ultrasonic Multi-Purpose Parts Cleaner
    (Part #91080304)
    x
                

    This ultrasonic parts cleaner is ideal for cleaning carburetor parts, fuel injector parts, small items such as wheel bearings, and other delicate components. Features a 6.6" x 5.4" x 2.5" tank size and includes a cleaning basket. 

    • Works on 110 volt power
    • Adjustable timer in 5 min. increments up to 30 mins.
    • Works well with a white vinegar solution
  • TCI 745504 Midplate Spacer Kit, 1/4 Inch Thick
    TCI 745504 Midplate Spacer Kit, 1/4 Inch Thick
    (Part #282745504)
    x
                

    TCI® Seven, Eight, Nine and Ten inch Race Torque Converters are designed to allow use with or without a midplate. The converter has the stock length nose piece. By removing the sleeve on the pilot, you can use this 1/4" extension.

    Contains:

    • 1 - Pilot Extension
    • 3 - 1/4" Washers
    • 3 - Long converter bolts

    Midplate Spacer Kit Instructions (PDF)

  • Intercomp Digital Pressure Tester
    Intercomp Digital Pressure Tester
    (Part #91381120)
    x
                

    This new pressure setting tool from Intercomp can be used for several jobs. This gauge will work from 0 to 150 psi. in 1/10th of a pound.

    Digital Pressure Tester

    • Large 1/2" back lite display.
    • Gauge features 1/10th of 1% accuracy.

    Setting Mid and High Speed bypasses
    1. Will work to set a high speed up to 150psi.
    2. Comes with a -6 AN female adapter to screw your high speed into

    Setting Tire bleeders

    1. Will work from 0 PSI up. With 1/10th of a pound increments.
    2. Comes with a female quick release fitting that fit the popular Kwick change bleeders.

  • GoJak Dollie Storage Rack
    $89.99
    GoJak Dollie Storage Rack
    (Part #880456)
    x
                

    Convenient storage cart handles up to four GoJaks® and fits all models. The cart loads and unloads in seconds and rolls easily to the job or storage area.

    Rack shown with four GoJaks®, which are not included.

  • Casters for Engine Storage Stand, Set/4
    Casters for Engine Storage Stand, Set/4
    (Part #91081139)
    x
                Casters are 3" x 1-1/4" inch wide making rolling  easier. Includes (2) swivel casters and (2) non-swivel casters. Swivel casters have double row swivel racelay. Each caster rated at  300lbs.
            
  • Wheel Rim Repair Wrench
    $20.99
    Product Rating: 4.50 Stars
    Wheel Rim Repair Wrench
    (Part #91082330)
    x
                

    This handy rim repair wrench allows you to repair your steel racing wheels for less than the cost of a new wheel.

    • Special jaw radius fits perfectly over the lip of any wheel 
    • Straightens edges of the wheel & rolls the curl back into the wheel
    • Will not crease or crack the wheel
    • Heavy duty steel construction
  • Race Track Flag Set, 3 Ft. x 3 Ft.
    Race Track Flag Set, 3 Ft. x 3 Ft.
    (Part #91079050)
    x
                100% nylon racing track flags measure 3' x 3'. Each flag is mounted on a sturdy wooden dowel. Dowels measure 4' long and 17 mm in diameter.
            
  • Wehrs Adjuster Wrench for Spring Slider
    Wehrs Adjuster Wrench for Spring Slider
    (Part #91045260)
    x
                

    These adjuster wrenches for Wehrs spring sliders are machined from quality aluminum.  They are durable and safe for use in the pits or in the shop.

    • Racing spring slider adjuster wrench
    • CNC-machined aluminum
  • POP Fasteners PS15-CS POP Hand Rivet Gun
    POP Fasteners PS15-CS POP Hand Rivet Gun
    (Part #91004010)
    x
                

    Ergonomic, jam free design with patented compound link that does the work for you. 50% easier to use than any other hand rivet tool on the market.

    • Robust aluminum casting with vanadium steel handle
    • Setting capacity: aluminum rivets up to 3/16" body diameter
    • Contoured handle grips for comfort
    • Rivet retaining handle design for one-handed riveting
    • Supplied with nosepieces for 3/32", 1/8", 5/32" & 3/16" rivets
    • Supplied nosepiece wrench
    • Length: 9.65"
    • Weight: 1.3 lbs.

    Hand Rivet Gun Instructions (PDF)

  • Race Ramps RR-FS FlatStoppers
    $249.99
    Race Ramps RR-FS FlatStoppers
    (Part #2367000)
    x
                

    FlatStoppers were developed as a solution for people having problems with tires developing flat spots when a vehicle is parked for 30 days or longer. Once tires are set on FlatStoppers (on a level surface), they settle into the pad's concave depression, which helps support more of
    the tire. This disperses the weight of the car more evenly onto the tire - helping to prevent any flat spotting. The pads measure 22.3" long x 3.5" high x 14" wide, and will accommodate tires up to 12" wide.

    FlatStoppers will not conduct heat or cold into your tires despite changing floor temperatures.

    Flatstoppers are made with the company's patented super-lightweight 100% solid construction technique - making them highly durable, virtually indestructible, and providing a 6,000 lb. vehicle weight capacity. FlatStoppers' textured coating prevents sliding across floors - including epoxy-coated floors and RaceDeck.

    FlatStoppers won't scratch or otherwise damage floors, and won't rust.

    Rebate  Feb2 - March 31 2015 (PDF) 

     

  • Heads for Grooving Iron
    $12.99
    Heads for Grooving Iron
    (Part #91082061)
    x
                

    Grooving Iron heads for grooving irons listed below.

    • 445-250 - Tru-Hot Grooving Iron
    • 445-251 - Ideal Grooving Iron
    • 910-82065 - Econ-o-siper

    Grooving Iron Replacement Heads and Blades Application Chart

  • Titan Tools 51503 Mini Tubing Bender
    $14.99
    $19.97
    Product Rating: 4.50 Stars
    Titan Tools 51503 Mini Tubing Bender
    (Part #72851503)
    x
                
    • Bends 1/8, 3/16, and 1/4" tubing up to 90 degrees
    • Use with Brass, Copper, Steel, or Aluminum
    • Compact for limited accessibility applications
  • Speedway Shock Wrench, QA1 Big Body
    $59.99
    $99.99
    Speedway Shock Wrench, QA1 Big Body
    (Part #9161000)
    x
                
    • CNC machined aluminum
    • Extra long handles for maximum leverage
  • Tire Stagger Tape, 10 Feet
    $5.99
    Tire Stagger Tape, 10 Feet
    (Part #91082015)
    x
                Stagger tape features thumb locking feature. 10' long, 1/4" wide steel tape. Use to measure tire circumference. 
            
  • Wheel Stud Drill Bit
    $9.99
    Product Rating: 3.60 Stars
    Wheel Stud Drill Bit
    (Part #91082007)
    x
                

    43/64" wheel stud drill bit with 1/2" shank. Used to drill out hubs and axle flanges for 5/8" wheel studs with .685 knurl diameter.

  • RapidAir M3800 Master Air Line Kit, 1/2 Inch Line
    RapidAir M3800 Master Air Line Kit, 1/2 Inch Line
    (Part #9103800)
    x
                These airline kits work great for your workshop with  applications from  automotive to woodworking. This is a complete  compressed air  distribution system that is designed to easily install within new walls  or on wall surfaces of existing  workshops/garages.  These kits allow  you to put air lines exactly where  you want them, just like electrical  outlets.   No more dragging hoses  across the shop to your work area.    No special tools required, simply push the flexible tubing into the  fittings and put up your system in an afternoon.
    • 1/2" line 
    • Operating pressure: 175psi at 70° F / 140psi at 140° F
    • Meets OSHA guidelines
    • Temperature range: -40° F to 140° F
    • Compatible with common compressor oils

    Kit Includes:  

    • 100 ft. of 1/2" ID Tubing
    • 3 Outlets
    • 1 Manifold
    • 5 Elbows
    • 1 Tee
    • Tools     (air chuck & filter regulator sold separately)

    Airline Installation Manual (PDF)

    RapidAir Maxline Warranty (PDF)

  • Conroy Pneu Bleeder Poppet Bleeder Kit for Winters Midget Axle
    Conroy Pneu Bleeder Poppet Bleeder Kit for Winters Midget Axle
    (Part #9501300)
    x
                Don't let centrifugal force control your bleeders. By mounting your bleeders in the center of the axle axis, these forces are eliminated and allow the bleeder to do the job it was intended to do. Also available in diaphragm style.
            
  • Saldana Racing WW-S20 Outlaw Sprint Lug Knock-Off Wrench Tool
    Saldana Racing WW-S20 Outlaw Sprint Lug Knock-Off Wrench Tool
    (Part #94082314)
    x
                

    Allows for easy removal of lug nuts. Lightweight, strong and durable aluminum construction for longevity. Wheel wrench features a 12 point socket.

  • Clipboard with One Robic SC-505 Stopwatch and Lap Sheets
    Clipboard with One Robic SC-505 Stopwatch and Lap Sheets
    (Part #91082031)
    x
                

    Aluminum clipboard with rubber feet holds stopwatches at an angle for easy viewing. Includes one pad of timing sheets, a pen, and one Robic SC-505 stopwatch.

    Operation Instructions (PDF) 

Goto Previous PagePrevious Page
1 2 3 4 5 ... 50