The right tools can make any job easier. Whether you are working in the shop, in the pits or on a new engine, Speedway Motors has the tools you need to get the job done quickly and done right.
"Tools, Hand Tools" Page 1 of 6
$20.99More InfoWheel Rim Repair Wrenchx
This handy rim repair wrench allows you to repair your steel racing wheels for less than the cost of a new wheel.
- Special jaw radius fits perfectly over the lip of any wheel
- Straightens edges of the wheel & rolls the curl back into the wheel
- Will not crease or crack the wheel
- Heavy duty steel construction
$14.99$19.97More InfoTitan Tools 51503 Mini Tubing Benderx
- Bends 1/8, 3/16, and 1/4" tubing up to 90 degrees
- Use with Brass, Copper, Steel, or Aluminum
- Compact for limited accessibility applications
$9.99More InfoPerformance Tool W54220 Grease Suction Gunx
Great for filling or emptying rear ends and trannys. You shouldn't be without one!
$9.99More InfoDECO Angle Finder Toolx
Used for setting pinion angle, and critical chassis components such as panhard bar, etc. Magnetic base.
$2.99More InfoGreen Plastigauge for Bearing Clearance, .001-.003 Inchx
Place a piece of this thread on a rod or main journal, torque cap in place, remove cap and by using the included chart, you know what your bearing clearance is. You should have one of each when assembling your engine.
$7.99More InfoPerformance Tool W750 7-Piece Chisel Setx
Get the job done with this 7-piece chisel set from Performance Tool.
- Hardened and tempered high carbon steel construction
- Vinyl covered shank absorbs shock and reduces vibration
- Handy storage pouch
- Pin punch sizes: 3/16" x 6"
- Taper punch sizes: 1/8" and 3/16" x 6"
- Center Punch sizes: 3/8"
- Cold Chisel sizes: 3/8", 1/2" and 5/8"
$6.99More InfoLarge Sheet Metal Scribex
Simplify your metal working jobs with this new tool. Simply run the tool down the edge of your material allowing the needle to locate perfectly measured lines every time. Stainless Steel construction. Measures .50", .75", 1", 1.5", and 2" depths.
$4.99$7.49More InfoSpeedway Mini Magnetic Parts Tray, 5-7/8 Inch Diameterx
These magnetic parts trays are perfect for holding small parts, hardware and fasteners in place. They are a 5-7/8" stainless steel dish with a rubber covered magnetic base to prevent scratching.
- 5-7/8" stainless steel dish
- Perfect for holding small parts, hardware and fasteners in place
- Sticks to any ferrous metal surface - it even works upside down
- Rubber covered magnetic base prevents scratching
$9.99More InfoCleco Steel Fastener Pliers Toolx
Speedway Motors has you covered when it comes to the tools and supplies that you need to have on hand to get the job done right. These Cleco pliers are quality-made, unique tools that readily install and remove Cleco fasteners.
Time saver when installing body and interior kits.
Cleco Steel Fastener Pliers Tool
$2.99More InfoSingle-Edge Razor Blade Nonscratch, Plastic, .040 Inch Thickx
These plastic razor blades are great for removing decals. They are a non-scratch, single-edge blade and come in packs of 5.
- Great for removing decals
- Single-edge blade
- 0.040" thick
- Pack of 5
$17.99$19.98More InfoTitan Tools 22400 Heat Gunx
- 12.5 Amps 120V Heat Gun
- Ideal for plastic welding, shrink tubing, and paint stripping
- Dual temperature setting
- 3 position rocker switch: off, high & low
- Durable ABS body
- Double insulated
- 6 1/2 ft. cord
- Rated Power: Low Setting 750W, High Setting 1500W
- Blowing Speed: Low Setting: 10CFM (280 L/min), High Setting: 17CFM (480 L/min)
- Temperature: Low Setting: 572 degrees, High Setting: 932 degrees
$16.99More InfoJAZ Products 550-014-06 Triangular Red Funnel Without Filterx
Triangular shape funnel allows fast flow. Features large 13" opening and anti-slosh lip. Red only.
$32.99More InfoSpeedway Quick Change Lug Wrenchx
The quick change lug wrench has a center handle and is free spinning for quick lug nut changes. Fits 1" lug nuts. Chrome plated.
$19.99More InfoSlider Rebuild Kitx
Contains the slider shaft, brass shaft piston, and the brass shaft guide nut.
$11.99More InfoPerformance Tool W80274 T-Handle Wrench Set - 10 Piecex
Includes 3/32"-3/8" wrenches and stand.
$39.99More InfoOil Filter Cutterx
Open filter and detect problems inside the motor. Anodized aluminum with adjustable threaded steel shaft. Universal, works on filters 1-1/2" to 6-1/8" in diameter. Includes one cutting blade.
$13.99More InfoDeburring Toolx
Every shop worth their salt has a deburring tool in their toolbox. Anytime you drill or mill a hole you should deburr it.
Includes 2 blades.
$10.99More InfoCompact Spark Plug Light and Magnifierx
All sharp mechanics have always done plug readings to help them get peak engine performance. Now you can too, with this clever spark plug viewing light and magnifier. Batteries not included.
Compact model includes carrying case, and is small enough to fit in your shirt pocket!
$24.99More InfoMechanix Wear MHS-05-500 Heat Sleevesx
Comfortable work sleeve designed for working in uncomfortable areas. Heat resistant and fire retardant. Treated with FibreShield to repel soil, fuel and water. 100% woven Kevlar. 18" long with thumb cut out.
$4.99More InfoNitrile Mechanics Glovesx
All the car dealer mechanics now wear these gloves to save their hands from solvents and oil. Perfect for home garage use when tearing down engines and trannys. Resists solvents, oil and chemicals. One size fits all. Latex free, reusable. 24 gloves per container.
Performance Tool W9181 1-1/4 Inch Wide Stainless Gasket Scraper Toolx
These multi-purpose gasket scrapers feature a rigid 1-1/4" wide stainless steel blade that extends through to the heavy duty metal capped handle for strength and durability.
- 1-1/4 Inch Wide
- stainless steel blade
- Handle Material: Plastic/Rubber
$39.99More InfoExtended 1 Inch Impact Speed Socketx
Use our speed-socket to change tires in a hurry. No spooky extension and socket to fly off. For 1" lug nuts and 1/2" impact. 13" long. Features a relief machined deep enough to accept lug studs up to 4" long.
$25.99More InfoAfco Twin Tube Bleederx
Afco shock rebuild tools.
$13.99More InfoHeavy Duty Nut Splitterx
Removes rusted, stripped and stubborn nuts and has a self-centeing wobble tip. Has offset design for easier operation and splits nuts from 7/16" to 3/4."
$29.99More InfoBearing Race and Seal Driver Setx
Quickly and easily installs wheel bearing races and seals without destruction to race or axle housing.
Set includes six discs to fit common bearing sizes: 1.565", 1.75", 1.965", 2.325", 2.47" and 2.555".
$6.99$9.98More InfoTitan Tools 51613 Fuel And Air Conditioning Line Disconnectx
- For fast and easy separation of quick disconnect style fittings
- For use on 3/8", 1/2", 5/8", 3/4", lines
- Necessary for fuel, heater, and A/C line service on many late model vehicles
- Slidecard Packaging
$19.99More InfoHeavy Duty Braided Hose Cutterx
It's hard to cut stainless steel braided hose. These heavy duty cutters feature precision ground blades and the big 18-1/2" length makes cutting a breeze. Will cut AN 16 hose.
$5.99More InfoMud Scraperx
Includes two sizes of notched ends: one for removing mud from roll cages and a 6" blade for body panels. 18" handle. Tough, heavy duty plastic.
$89.99More InfoLaser Chain Alignment Toolx
- No More Measuring!
- Billet Construction
- Precision Accuracy
$6.99More InfoPerformance Tool W1219 Grease & Oil Seal Pullerx
For removal of grease and oil seals. Two tip sizes accomodate many applications.
$89.99More InfoPercy's 01201 Wheelritex
Nifty tool bolts to your brake rotor or drum and allows you to determine what width, diameter and offset wheels will fit your car. It will simulate 6" to 11" or more width and 15" to 30" height. Fits four or five lug bolt patterns from 4" to 5.5".
Make your selections, then give it a spin! Check clearance at every point in the rotation.
$19.99More InfoCleco Tool, Fasteners, and Clamp Kitx
A real time saver when installing body and interior kits. Eliminates need to drill into body. Vise head grips up to 9/16". The Cleco pliers are quality-made, unique tools that readily install and remove Cleco fasteners.
Cleco pins are a definite must for sheet metal fabrication. They're basically spring-loaded, removable pop rivets that allow you to hold two pieces of sheet metal together in proper alignment for drilling or riveting. They work great for Circle Track use for test-fitting panels before they're permanently attached to your vehicle.
The pins work with thicknesses of up to 1/4 in.
Cleco Tool, Fasteners, and Clamp Kit:
- (1) one tool
- (20) twenty 3/16" clecos
- (1) one clamp
$6.99More InfoExtended Spark Plug Socket, 5/8 Inchx
This 5" long socket allows you to easily install and remove 5/8" hex spark plugs without burning your fingers on the headers. Knurled for added grip. Fits 3/8" drive.
$80.99More InfoChain Breaker Press And Riveting Toolx
- Complete chain tool for most 520, 525 and 530 standard o-ring chains
- Break, press and rivet your chain with one compact tool
- Will rivet hollow nose master links (will not rivet solid soft-nose pins)
- Will push pin completely through link/side plate
- Hardened body, riveting tip and breaker pin for strength and durability
- Removable handle for compact storage
- Perfect for your tool chest if you have a chain with a rivet master link
- 1 year limited warranty
$9.99More InfoDead Blow Hammerx
Ideal for all mechanical work; assembly of engines, shafts, etc. Will not mar surface. Weighs 2 lbs.
$34.99More InfoAluminum Adjustable AN Wrenchx
The perfect AN wrench! This 8" aluminum adjustable wrench will fit just fine in your back pocket or glove box. Maximum opening is 1-1/4".
$54.99More InfoSpeedway Aluminum AN Wrenchesx
Get rid of that adjustable wrench and never ruin a fitting again! These beautifully CNC manufactured AN wrenches are designed with the correct length handle to avoid over-tightening. Each wrench has the fitting size stamped on it for easy identification. Comes with AN 3, AN 4, AN 6, AN 8, AN 10, AN 12, AN 16, and AN 20 sizes.
We even throw in a free carrying case.
$19.99More Info1-7/8 Inch and 1-3/8 Inch Sprint Car Hub and Spindle Nut Wrenchx
No more banged up knuckles or scratched up Anodizing. This special aluminum box end wrench in 1-7/8” and 1-3/8” Hex will tighten up your spindle nuts.
Hub and Spindle Nut Wrench
- Durable stainless steel construction
- Sized for most popular combinations
- Saves time and frustration
- 1-7/8 Inch and 1-3/8 Inch Ends