Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 5

Products

Engine Service

Shop Engine Service At Speedway Motors

The right tools can make any job easier. Whether you are working in the shop, in the pits or on a new engine, Speedway Motors has the tools you need to get the job done quickly and done right.

Featured Products
  • Offenhauser Flathead Ford Pressure Tester Kit
    Offenhauser Flathead Ford Pressure Tester Kit
    (Part #56082260)
    x
                

    If you have built a Flathead Ford, you know the odds of the block being cracked are pretty high. Plus the cost of cleaning and magnafluxing keeps going up. This kit allows you to pressure test one cylinder bank at a time to detect cracks or holes in your own garage. Includes regulator head plate, water pump plates and hardware. For 24 stud Flathead Fords only.

    Flathead Block Pressure Testing Instructions 

  • Cam Bearing Driver
    $25.99
    Product Rating: 4.43 Stars
    Cam Bearing Driver
    (Part #91381102)
    x
                Remove and replace your S/B Chevy and 90° V6 cam bearings without damage to the bearings. 

    Note: Always remove cam bearings when boiling or cleaning block.

    913-81102 Instructions (pdf)

  • Top Dead Center Indicator
    $5.99
    Product Rating: 3.33 Stars
    Top Dead Center Indicator
    (Part #5503410)
    x
                Positive stop to locate top dead center. A must for cam checking with heads on. For 14 mm thread. 
            
  • Performance Tool W89716 Serpentine Belt Tool Kit
    Performance Tool W89716 Serpentine Belt Tool Kit
    (Part #91081008)
    x
                This tool kit allows you to replace the serpentine fan belt on many Ford, GM and Mopar vehicles. Also includes GM fan clutch wrench sockets and wrenches.  
            
  • Aeroquip FBM3632 Push On Fitting Tool for AN4, AN6, AN8
    Aeroquip FBM3632 Push On Fitting Tool for AN4, AN6, AN8
    (Part #6173632)
    x
                

    It's a pain to push that blue hose onto a fitting! With this tool you don't need a vise or any other tools. Simply lube the inside of the hose, clamp the hose and give the lever a pull!

    For AN 4, 6, 8 straight push-on fittings only.

  • Chevy Camshaft Install Tool
    $24.99
    Chevy Camshaft Install Tool
    (Part #58666897)
    x
                It's not too bad putting a Chevy cam in about 3/4 of the way. That's when you get shaky and start nicking the cam bearings. This tool bolts on the end of the cam and gives you the control to do the job right. Works great for taking the cam out too. This product is for non-roller camshafts.
            
  • Speedway Dual Gauge Leakdown Tester
    Speedway Dual Gauge Leakdown Tester
    (Part #91381121)
    x
                

    This dual gauge is ideal to check leak down and set barrel valves on fuel injection systems without running the engine. Detects ring seat failure, bent valves, cracked heads, and leaking gaskets. Works best with 100+ psi air source.

    Includes a 21" quick-disconnect hose to connect from the gauge to the spark plug hole. The threads on the the spark plug end are 14mm with an O-ring seal.

    913-81121 Instructions (PDF)

  • Koul Tools 409 EZ-On Hose Press Tool
    New
    Koul Tools 409 EZ-On Hose Press Tool
    (Part #469409)
    x
                

    This EZ-On hose press from Koul Tools is used for Installing push on fittings. The new tool will install -4 thru -16 push-on hose onto the fittings in seconds.

    • Constructed of investment cast steel
    • All components are fitted Into custom carrying case for safe storage and transportation
    • Designed to install push-on hose onto any angle or straight fitting

Filter

"Tools, Engine Service" Page 1 of 5

Page 1 of 5

  • Head Stud Remover and Tap Alignment
    Head Stud Remover and Tap Alignment
    (Part #91081131)
    x
                

    Allows removal of stock press-in studs and aligns the tap (7/16"-14) to simplify the installation of screw in rocker studs.

    For S/B Chevy V8 engines.

  • Valve Spring Tester
    $199.99
    Valve Spring Tester
    (Part #91681150)
    x
                Black anodized aluminum. Most convenient Valve Spring Tester on the market. Set spring height once and test as many springs as you want, with little effort. Handles up to 600 lb. springs.
            
  • Dorman 550-017 Concave Expansion Freeze Plugs, 1.250 Inch Steel
    Dorman 550-017 Concave Expansion Freeze Plugs, 1.250 Inch Steel
    (Part #5504490)
    x
                Complete freeze plug kits available in steel for GM OE#: 1489745.                               
    • 1.250" steel Concave Expansion Plugs
    • Box of 10
    • Direct cross to GM OE#: 1489745
  • Piston Ring Squaring Tool, 4.000 to 4.230 Bores
    Piston Ring Squaring Tool, 4.000 to 4.230 Bores
    (Part #91089415)
    x
                

    For checking piston ring end gap. One tool covers 4.000" thru 4.230".  Anodized aluminum. Designed to fit inside head studs.

    Ring Style Chart

  • Jesel and T&D Valve Spring Tool
    Jesel and T&D Valve Spring Tool
    (Part #91081062)
    x
                For use with standard Jesel rockers. Allows you to remove LH or RH valve springs. 
            
  • Replacement Diamond Cut Disc for Ring Filer
    Replacement Diamond Cut Disc for Ring Filer
    (Part #91089420)
    x
                Replacement diamond cut grinding disc for ring filer. The disc measures 2-1/4" across and has a 1/4" pilot hole.
            
  • Pushrod Length Checker, 8.5-9.8 Inches
    Pushrod Length Checker, 8.5-9.8 Inches
    (Part #28799722)
    x
                

    You always need to find the correct length for your push rods when you build an engine. Having the wrong length changes the geometry of the valve train and decreases horsepower while increasing wear.

    • Adjustable to fit several engines
    • Enables you to arrive at correct pushrod length and correct valve train geometry
    • Minimum length is 8.5" and maximum length is 9.8"
    • Includes two per package (check both intake and exhaust)
    • 5/16" diameter
  • Speedway Dial Indicator
    $19.99
    Product Rating: 4.00 Stars
    Speedway Dial Indicator
    (Part #91082721)
    x
                2-3/8" diameter face, measures in .001" increments. Probe has 1" stroke. Includes bracket on the back.
            
  • Small Block Chevy Deluxe Oil Pump Primer
    Small Block Chevy Deluxe Oil Pump Primer
    (Part #54522060)
    x
                

    Strong and Durable S/B Chevy oil pump primer. Features a special bushing to allow the lifters to be lubed.

  • Isky Racing Cams 7-DW 7 Inch Degree Wheel
    Isky Racing Cams 7-DW 7 Inch Degree Wheel
    (Part #4507DW)
    x
                7" diameter. Heavy gauge aluminum discs calibrated in 1° increments for determining precise valve, cam and ignition timing.
            
  • Valvetrain Organizer Tray
    $35.99
    Product Rating: 4.60 Stars
    Valvetrain Organizer Tray
    (Part #2514394)
    x
                This tray allows you to keep your valve train components organized and mated during assembly or disassembly. Lightweight plastic tray features individual compartments that allow you to store rocker arms, pushrods, valve springs and most other valve train items. 
    23-1/4" x 12-3/8" x 1-5/8"
  • Manley 42132 Small Block Chevy Pushrod Length Checker, 7/16 Stud
    Manley 42132 Small Block Chevy Pushrod Length Checker, 7/16 Stud
    (Part #50542132)
    x
                

    For Small Block Chevy. Just slip it over a 7/16" rocker arm stud to instantly tell how much longer or shorter the push rods need to be.

    • Long valves, milled heads, cut blocks, small base circle camshafts all move rocker geometry far from optimum
    • Correct length pushrods keep rockers centered on the valve tip and reduce stem and guide wear
    • Checker tells the engine builder instantly what length pushrod is required
  • Speedway Dual Gauge Leakdown Tester
    Speedway Dual Gauge Leakdown Tester
    (Part #91381121)
    x
                

    This dual gauge is ideal to check leak down and set barrel valves on fuel injection systems without running the engine. Detects ring seat failure, bent valves, cracked heads, and leaking gaskets. Works best with 100+ psi air source.

    Includes a 21" quick-disconnect hose to connect from the gauge to the spark plug hole. The threads on the the spark plug end are 14mm with an O-ring seal.

    913-81121 Instructions (PDF)

  • Precision Piston Ring Filer
    $39.99
    Product Rating: 4.60 Stars
    Precision Piston Ring Filer
    (Part #91089408)
    x
                

    Set ring end gap with this exclusive filer. Features carbide grinding wheel and cuts chrome plated stainless steel quickly and accurately. Can be mounted to any work bench.

  • Intercomp 100450 Digital Valve Spring Tester
    Intercomp 100450 Digital Valve Spring Tester
    (Part #91081060)
    x
                

    Ideal for checking valve spring on an assembled motor. Easily detects broken or fatigued springs.

    0-500 lbs in 5 lb increments.

  • LSM Racing Products SC-100 Valve Spring Compressor
    LSM Racing Products SC-100 Valve Spring Compressor
    (Part #91081135)
    x
                This is the best tool we have seen for removing valve spring with your head installed, it makes it a one man job. This tool works with S/B Chevy with Jesel, T&D and Buick heads as well as Dodge W-8 with Jesel, FE Ford - Jesel only, Chrysler Indy 440-1 head with Jesel, and the Barton Hemi exhaust only with slight modification.
            
  • Moroso 62250 Mopar V8 Oil Pump Primer
    Moroso 62250 Mopar V8 Oil Pump Primer
    (Part #54562250)
    x
                

    Use with an electric drill to prime engine before starting. Remove the distributor and insert this primer to engage the end of the oil pump drive.

  • Moroso 62210 Ford 289, 302, 390, 428 V8 Oil Pump Primer
    Moroso 62210 Ford 289, 302, 390, 428 V8 Oil Pump Primer
    (Part #54562210)
    x
                

    Use with an electric drill to prime engine before starting. Remove the distributor and insert this primer to engage the end of the oil pump drive. Pump drive end of the primer fits 1/4" hex male end of the oil pump drive. 9" total length.

  • Pushrod Length Checker, 6.125-7.5 Inches
    Pushrod Length Checker, 6.125-7.5 Inches
    (Part #28799720)
    x
                

    You always need to find the correct length for your pushrods when you build an engine. Having the wrong length changes the geometry of the valve train and decreases horsepower while increasing wear.

    • Adjustable design fits several engines
    • Enables you to arrive at correct push rod length and correct valve train geometry
    • Minimum length is 6.125" and maximum length is 7.5"
    • Includes two per package (checks both intake and exhaust)
    • 5/16" diameter
  • Universal Cam Bearing Driver
    $202.99
    Universal Cam Bearing Driver
    (Part #58666820)
    x
                This cam bearing driver set is just like your engine shop uses. The expanding plugs can install most any bushing from 1-1/4" to 2.69" i.d. and comes in a carrying case. 
            
Goto Previous PagePrevious Page
1 2 3 4 5