Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Canadian Leaf
Products

Shop T-Bucket At Speedway Motors

Speedway Motors’ fantastic selection of ready-to-assemble T-Bucket kits makes it easy and affordable to build a fun, personalized street rod! Speedway kit car packages are designed with the do-it-yourself enthusiast in mind. A variety of crate engines and all engine components are offered for any application. The hand-made fiberglass roadster bodies, frames, and wiring harnesses are engineered for simple, bolt-together construction, making them perfect for rookie rodders and seasoned pros alike.

Featured Products
Small Block Chevy 4340 Steel H-Beam Rods, Bushed Pin
Small Block Chevy 4340 Steel H-Beam Rods, Bushed Pin
x
            

Heavy duty H-beam connecting rods for S/B Chevy. Full floating wrist pin in silicon bronze bushing. Precision bolt bushing to positively locate cap. Features 8640 PCE 7/16" cap screws.

Weight matched sets of 8. Available in 5.7" or 6.0" lengths.

Speedway Economy 12 Circuit Wiring Harness
Speedway Economy 12 Circuit Wiring Harness
x
            

This harness was designed to offer you all the highest quality components in a package designed for cars with minimum accessories. Each wire is color coded and labeled every few inches.

Our prewired 12 circuit kit will fit all your basic needs and makes wiring a painless process. It is designed especially for the street rod without accessories. It also includes horn relay and connector, turn and hazard signals, dimmer switch connector, circuit breaker for headlights, two flashers, one alternator plug, two ignition switch connectors, plus more.

  • Mainfuse box base is 1-7/8" x 3-11/16"
  • Box height is 3-3/4"
12 Circuit Wiring Harness Installation Instructions (PDF)
Speedway 1928-1948 Ford Forged Spindles w/ King Pins
Speedway 1928-1948 Ford Forged Spindles w/ King Pins
x
            

These Speedway spindles are one piece, drop forged design constructed of high strength 4140 steel, which makes them superior to original components. These spindles are modeled after the '37-'41 round-back design and use '37-'41 Ford king pins.

These spindles fit Ford axles from '28-'48. They can be used with period correct drum brakes or modern Speedway Motors disc brakes, but will not work with hubs from '28-'36.

  • Uses 1937-1941 king pin kit
  • For Ford axles 1928-1948
  • Will not work with 1928-1936 Hubs
  • Includes king pin kit

Be sure to include our spindle nut kit (910616004) to properly install these spindles.

Spindle Identification Guide (GIF)

910-32104 Instructions (PDF)

Ford 9 Inch Posi Traction Third Member Assembly
Ford 9 Inch Posi Traction Third Member Assembly
x
            

Speedway Motors now offers you a 9" Ford street 3rd member for your street rod. We reclaim genuine Ford 9" housings, clean, inspect and install all new components. All bearings, seals, 1310 series yoke and ring & pinion are new!

These Ford 9" 3rd member assemblies feature new Pro Gears ring & pinion, choice of 3.50, 3.70, 3.89, 4.11 or 4.56, Currie 9-Plus limited slip differential, 28 or 31 spline. Shipped in handy plastic carrying case. Assembled by professionals.

 

Currie Differential Tech Bulletin (PDF)

 

910-48345 Instructions (PDF)

Speedys 9 Super 7    Primary 3-Bolt 2 Barrel Carburetor, Plain Finish
Speedys 9 Super 7 Primary 3-Bolt 2 Barrel Carburetor, Plain Finish
x
            

Speedway Motors now offers a reproduction version of one of the most popular carburetors ever used, the original Stromberg 97! Original equipment on '30s and '40s cars and trucks, the Stromberg 97 has long been favored by flathead hot rodders and racers who realized the performance qualities of this timeless fuel supplier.

There have been numerous attempts to reproduce this unit, with little success. "Speedy" Bill Smith of Speedway Motors in Lincoln, Nebraska, took on the challenge to make a great product even better. The 9 Super 7 ® Carb brings this reproduction of the original Stromberg 97 2 barrel carb into the 21st Century!

Speedway Motors has incorporated all of the improvements shown above while maintaining the carburetor's original look. Features such as the choke assembly, accelerator pump, main jets and cosmetics have all been faithfully retained. Additionally, each carburetor is individually flow tested and inspected for leaks. Perfection is the result! 

Aesthetically, the 9Super7 is nearly identical to the stock unit, minus the large 97 logo that appeared on the side and the patent numbers found on the float bowl area. Upgraded internal parts include; the float, needle, and seat. Jetting and power valve settings remain as they were for the original 97 carbs as well as the cfm and vacuum specs.

The other similarity that the 9 Super 7 shares with the original 97 is the setup and tuning necessary to yield a well-running machine. While perhaps not as simple as bolting on a single four-barrel, the 9 Super 7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required is an intake, a linkage system, a Uni-Syn syncing tool, and a little patience. Be sure to include the Secondary 9 Super 7 when installing multi-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb set-up.

  • All-new tooling for crisp, flawless castings
  • New aluminum base assembly allows for cooler fuel temps and better fuel efficiency as compared to the original cast iron design
  • Stainless steel screws and hardware
  • Choke assembly, accelerator pump, and jets have all been faithfully retained and accept standard Stromberg parts
  • Features original Stromberg 0.97" venturi diameter
  • Modern Nitrophyl float and Neoprene gaskets
  • Original troublesome needle and seat replaced by a Grose-style fuel inlet valve to better cope with higher fuel pressures and improved high speed running 
  • Will not stick or dribble like the old Viton-tipped needle and seat setups
  • Grose-style jet valve won't corrode in modern fuel, something the original needle and seat units can't do
  • Comes with a No. 65 power valve and 0.045" main jets, identical to the stock 97
  • Extended brass throttle shaft to simplify multi-carb linkage

915-11655 9 Super 7® Carb Instructions (PDF)

Speedway Universal 20 Circuit Wiring Harness
Speedway Universal 20 Circuit Wiring Harness
x
            Whether you're building an option loaded car or just want to have extra circuits available for future updates, this harness is perfect and makes any job painless. Compact 5-1/2"L x 4-1/2"W x 3-1/4"H  fuse block holds 18 standard push-in fuses and can be mounted almost anywhere. 

Each high temperature wire is color coded and labeled every six inches. Also includes GM type steering column connectors. To keep costs down and the quality high, this harness does not include any switches, light sockets or plugs that you would normally already have.

  • Harness has 20 circuits, of which 18 are fused
  • Taillight leads measure 17' long
  • Includes plug for GM column, headlight switch, dimmer switch, and signal flashers

Wiring Harness Installation Instructions (PDF)

9 Super 7   Secondary 3-Bolt 2 Barrel Carburetor, Plain Finish
9 Super 7 Secondary 3-Bolt 2 Barrel Carburetor, Plain Finish
x
            

Speedway Motors now offers a reproduction version of one of the most popular carburetors ever used, the original Stromberg 97! Original equipment on '30s and '40s cars and trucks, the Stromberg 97 has long been favored by flathead hot rodders and racers who realized the performance qualities of this timeless fuel supplier.

For years customers have been either putting up with poor idling multiple carburetor set-ups or spending hundreds of dollars converting the secondary carburetors so they did not have to idle circuits. Now Speedway Motors is offering our popular 9 Super 7® two barrel "secondary" carburetor with all that work already done. No more wasted money!

Speedway Motors has incorporated all of the improvements shown above while maintaining the carburetor's original look. Features such as the accelerator pump, main jets and cosmetics have all been faithfully retained. Additionally, each carburetor is individually flow tested and inspected for leaks. Perfection is the result! 

Aesthetically, the 9Super7 Carb is nearly identical to the stock unit, minus the large 97 logo that appeared on the side and the patent numbers found on the float bowl area. Upgraded internal parts include; the float, needle, and seat. Jetting and power valve settings remain as they were for the original 97 carbs as well as the cfm and vacuum specs.

The other similarity that the 9 Super 7 shares with the original 97 is the setup and tuning necessary to yield a well-running machine. While perhaps not as simple as bolting on a single four-barrel, the 9 Super 7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required is an intake, a linkage system, a Uni-Syn syncing tool, and a little patience. Be sure to include the Primary 9 Super 7 when installing multi-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb set-up.

  • All-new tooling for crisp, flawless castings
  • New aluminum base assembly allows for cooler fuel temps and better fuel efficiency as compared to the original cast iron design
  • Stainless steel screws and hardware
  • Accelerator pump, and jets have all been faithfully retained and accept standard Stromberg parts
  • Features original Stromberg 0.97" venturi diameter
  • Modern Nitrophyl float and Neoprene gaskets
  • Original troublesome needle and seat replaced by a Grose-style fuel inlet valve to better cope with higher fuel pressures and improved high speed running 
  • Will not stick or dribble like the old Viton-tipped needle and seat setups
  • Grose-style jet valve won't corrode in modern fuel, something the original needle and seat units can't do
  • Comes with a No. 65 power valve and 0.045" main jets, identical to the stock 97
  • Extended brass throttle shaft to simplify multi-carb linkage
  • Special base plate with no idle circuits or choke linkage
  • Special butterflies and shafts installed
  • Works best with progressive linkage
  • Idle only off the center or main carburetor
  • No more plug foul
Smoothie Rams Horn Exhaust Manifolds, Small Block Chevy, Raw
New
Smoothie Rams Horn Exhaust Manifolds, Small Block Chevy, Raw
x
            

These classic "Rams Horn" style exhaust manifolds are great for use with most small block Chevy applications, providing optimal clearance for angle plug heads.  These manifold kits come complete with all mounting hardware and gaskets.

  • Ground smooth with no external bosses or brackets
  • 2-1/2" outlet
  • Plain, Raw finish
  • Nodular cast iron
  • For angle or straight plug heads
  • Includes all hardware and gaskets

"T-Bucket" Page 1 of 25

  • Head Stud Remover and Tap Alignment
    Head Stud Remover and Tap Alignment
    x
                

    Allows removal of stock press-in studs and aligns the tap (7/16"-14) to simplify the installation of screw in rocker studs.

    For S/B Chevy V8 engines.

  • Magnetic Drain Plug
    $3.99
    Product Rating: 5.00 Stars
    Magnetic Drain Plug
    x
                

    Metal debris can wreak havoc on an engine. Install this plug in your oil pan to catch any metal filings before they get sucked into the oil pump and cause real damage!

    Will fit any oil pan with 1/2-20 threads.

  • Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    Inverted Flare Thread Nuts for 3/16 Inch Tubing, 3/8-24
    x
                

    Steel 3/8"-24 IFM thread nuts for 3/16" brake line when double flared to 45°.

  • 1928-31 Model A Front Crossmember
    1928-31 Model A Front Crossmember
    x
                

    These replacement 1928-31 Model 'A' Ford front crossmembers lower a Model A chassis 2" below a stock crossmember. Replaces a cracked original or use it to start your reproduction frame off right. Made of heavy, 7-gauge steel with clearance for 1-3/4" cross spring. Welds to frame boxing plates of original or repro chassis.

  • Speedway Ultrasonic Multi-Purpose Parts Cleaner
    Speedway Ultrasonic Multi-Purpose Parts Cleaner
    x
                

    This ultrasonic parts cleaner is ideal for cleaning carburetor parts, fuel injector parts, small items such as wheel bearings, and other delicate components. Features a 6.6" x 5.4" x 2.5" tank size and includes a cleaning basket. 

    • Works on 110 volt power
    • Adjustable timer in 5 min. increments up to 30 mins.
    • Works well with a white vinegar solution
  • SPAL Thermoswitch Relay and Wiring Harness Kit
    SPAL Thermoswitch Relay and Wiring Harness Kit
    x
                

    This easy to use cooling fan relay kit includes a labeled wiring harness, 40 amp relay, fuse holder and coolant sensor. Available with 185° on/165° off or 195° on/175° off. Works great with the Spal Pulse-Width Fan Controller.

    • Relay wiring kits are a must-have when installing an electric fan
    • Designed to safely integrate with OEM wiring
    • Waterproof 40/50 Amp relay
    • Printed wires (for ease of installation)
    • 3/8" NPT (National Pipe Thread) stainless steel switch
    • Optional switched override capability
    910-64028 Instructions (PDF)
  • Modern Driveline Reverse Switch Harness for GM T5 and T56 Transmissions
    Modern Driveline Reverse Switch Harness for GM T5 and T56 Transmissions
    x
                

    These harnesses for transmission neutral safety switch/reverse light switches are designed for use with GM T5 and T56 transmissions.

    • Factory style
    • For GM T5 and T56 transmissions

     

  • Rocker Arm Balls for 7/16 Inch Stud
    Rocker Arm Balls for 7/16 Inch Stud
    x
                Replacement rocker arm pivot balls with oil slots. Comes in a set of 16 for use with 7/16" rocker arm studs.
            
  • 3X Chemistry Satin Rust Encapsulator, Quart
    3X Chemistry Satin Rust Encapsulator, Quart
    x
                3X:Chemistry Encapsulator is a single component, high solids paint   specially formulated to bond to blasted or rusted metal surfaces. The   coating forms a rock hard finish that's flexible, non-porous and will   not crack, chip, flake or peel. No hardeners or activators are needed.   Encapsulator is completely unaffected by salt, gasoline, oils, battery   acids, hydraulic fluids, solvents, chemicals, or corrosives.
    • Permanently stops rust and corrosion
    • Can be sprayed or brushed over rusted surfaces
    • Reusable after opening
    • Highest percentage of solids
    • Available in Satin

    30746817 Material Safety Data Sheet (PDF)

  • Universal Expanding Body Mounts
    Universal Expanding Body Mounts
    x
                

    If you are building a lightweight car like a "T" or an "A", mounting the body may present a problem. These neat expanding rubber universal body mounts allow you to drill a 3/4" hole in the top of the frame, insert a 3/8" coarse bolt, tighten, then the body is mounted.

    Not recommended for cars newer than 1934.

  • DEi 010502 Protect-A-Boot Spark Plug Boot Heat Shield, 6 Inch, Silver, 8 Pack
    DEi 010502 Protect-A-Boot Spark Plug Boot Heat Shield, 6 Inch, Silver, 8 Pack
    x
                

    Protect-A-Boots are made from a high temperature resistant glass fiber material and treated with a proprietary coating, Protect-A-Boots provide spark plug boot and wire protection from extreme under hood heat.

    • Double-wall construction for added durability
    • Helps prevent burn-through, hardening and cracking of boots
    • Installs in seconds
    • Universal-fits most straight or angled boots
    • Withstands 1200°F direct continuous heat
    • Non-flammable & protects against chemicals & resists water

    Protect-A-Boot Instructions (PDF)

    Exhaust Wrap Frequently Asked Questions (PDF)  

     

  • Tall Model T Cowl-Tail Lights, Black
    Tall Model T Cowl-Tail Lights, Black
    x
                

    Features a 12 volt dual element bulb and can be used as a tail light or a cowl light. 9-1/2" tall with 3" diameter lens. Specify red or amber lens.

    Note: Mount bracket is NOT included. Lens must be secured in place with silicone (see Instructions).

    Cowl Light Installation Instructions (PDF)

  • Axle Spring Perch, Plain Forged Steel
    Axle Spring Perch, Plain Forged Steel
    x
                Works with 1928-34 Ford front ends with 1-3/4" wide cross spring. Extra long for lower shock mounts. Includes nylock nut.
    • 2-1/2" from top of threads to mid shoulder
    • 2-7/8" from top of threads to top of shoulder
    • Thread length is 1-7/8"
    • Distance from the top of the shoulder to the bottom of the threads is 4-3/4"

    Leaf Spring Measuring Guide (Link)

  • Titan Tools 51503 Mini Tubing Bender
    $14.99
    $19.97
    Product Rating: 4.50 Stars
    Titan Tools 51503 Mini Tubing Bender
    x
                
    • Bends 1/8, 3/16, and 1/4" tubing up to 90 degrees
    • Use with Brass, Copper, Steel, or Aluminum
    • Compact for limited accessibility applications
  • RapidAir M3800 Master Air Line Kit, 1/2 Inch Line
    RapidAir M3800 Master Air Line Kit, 1/2 Inch Line
    x
                These airline kits work great for your workshop with  applications from  automotive to woodworking. This is a complete  compressed air  distribution system that is designed to easily install within new walls  or on wall surfaces of existing  workshops/garages.  These kits allow  you to put air lines exactly where  you want them, just like electrical  outlets.   No more dragging hoses  across the shop to your work area.    No special tools required, simply push the flexible tubing into the  fittings and put up your system in an afternoon.
    • 1/2" line 
    • Operating pressure: 175psi at 70° F / 140psi at 140° F
    • Meets OSHA guidelines
    • Temperature range: -40° F to 140° F
    • Compatible with common compressor oils

    Kit Includes:  

    • 100 ft. of 1/2" ID Tubing
    • 3 Outlets
    • 1 Manifold
    • 5 Elbows
    • 1 Tee
    • Tools     (air chuck & filter regulator sold separately)

    Airline Installation Manual (PDF)

    RapidAir Maxline Warranty (PDF)

  • 1909-12 Ford Model T Brass Glass Setting Channel for Open Cars
    1909-12 Ford Model T Brass Glass Setting Channel for Open Cars
    x
                Fits Ford Model T Roadster and Touring open top applications. Designed to use 3/16" thick safety glass or Lexan. Channel holds glass in the original frames.
            
  • Holley 20-132 LS Accessory Drive Bracket-ALT, P/S, A/C
    Holley 20-132 LS Accessory Drive Bracket-ALT, P/S, A/C
    x
                Please view the product's page for more information
            
  • Tru-Shot Rechargeable Liquid Sprayer, Black
    Tru-Shot Rechargeable Liquid Sprayer, Black
    x
                

    Great for use with Mudd-Off, Mud-X, Brake Kleen, penetrating oils or solvent based products. Not for all water based products.

    • One quart capacity
    • Powder coated steel can
    • Adjustable nozzle
    • Works with 80-100 psi
  • Synthetic Chamois
    $4.99
    $9.95
    Synthetic Chamois
    x
                

    Use on cars, furniture, glass, etc. Can be used wet or dry and washed up to 500 times. Big 26" by 19".

     

     

  • Lokar EHB-7000F Floor Mount Emergency Hand Brake, Chrome Finish
    Lokar EHB-7000F Floor Mount Emergency Hand Brake, Chrome Finish
    x
                

    This Lokar Floor Mount Emergency Hand Brake features a chrome plated steel e brake handle and is designed after the automotive industry standards. The ratchet cut gear plate and lock are heat treated for strength and safety. Special feature includes 4-point mounting capabilities for floor mount or side mounting for custom applications.

    Comes complete with clevis for installation with Lokar Emergency Brake Cables, Lokar # EC-80FU, Speedway Motors # 491-80FU suggested below. Cables are sold separately.

    Lokar Install Tip:  Every think about mounting the floor mount hand brake sideways in front of your seat?  You can!

  • Taylor 20314 14 Inch Braided Grounding Strap Cable
    Taylor 20314 14 Inch Braided Grounding Strap Cable
    x
                These braided grounding straps from Taylor Cable are 14" long 4-gauge and feature tin coated copper construction.
    • 14" long
    • 1" wide
    • Tin coated copper
    • 4-gauge

    Taylor Cable Warranty Sheet (PDF)

  • Panhard Bar Rear Weld-on Kits
    Panhard Bar Rear Weld-on Kits
    x
                

    Use on almost any street rod. Required for coil spring and coil-over rear suspensions. Complete kit includes rod, brackets and 5/8" hardware. Ready to install. 25.5" long.

    916-49022 Instructions (PDF)

  • 1932-1953 Flathead Ford V8 Single Valve Springs
    1932-1953 Flathead Ford V8 Single Valve Springs
    x
                

    Our complete line of valve train parts to help your flathead Ford V8 run on unleaded fuel. These heavy duty single valve springs are made from top-quality chrome silicon steel and are designed to work with stock 1932-1953 Ford retainers. 

    • Recommended for most street performance 1932-53 Ford/Mercury Flathead V8s
    • Chrome silicon material delivers reliable performance
    • Proper seat pressure for most street and street/strip Flathead cams
    • Installed Height:  2.00"
    • Seat Pressure:  85 lbs @ 2.00" installed height

    Note: "Full Race" cams should be paired with our 450-4005 dual valve springs.

    Flathead Valve Assembly (Link)

     

  • Metal Pegboard Tool Organizer, 32 x 32 Inch Wall Control Storage System
    Metal Pegboard Tool Organizer, 32 x 32 Inch Wall Control Storage System
    x
                Durable, all-steel construction will not warp, fray  or crack. Attractive, scratch  resistant,  baked-on powder coat finish wipes clean for long-lasting  beauty for any  shop or work area. Installation is easy and absolutely no  framework is  required. 
    • 32" tall x 32" wide x 3/4" deep
    • Pack of two
    • Durable and versatile
    • 20 gauge steel with a baked-on rust and scratch resistant finish
    • Slotted to accept Wall Control accessories
    • Holes accept conventional 1/4" peg hooks
    • Choose from blue, grey, red, white, or galvanized steel
  • Sweet Mfg. 001-21040 Rack and Pinion Replacement Boot
    Sweet Mfg. 001-21040 Rack and Pinion Replacement Boot
    x
                

    These high quality rubber replacement boots for Sweet Mfg. rack and pinions perform as good as they look.

    • Replacement for Sweet Mfg. rack and pinion
    • High quality rubber construction

     

  • Longacre Accuset II Scale Kit
    $999.99
    Product Rating: 3.00 Stars
    Longacre Accuset II Scale Kit
    x
                
    • Push one button for all 4 wheel weights plus cross weight
    • Push a second button for all partial %
    • Baseline memory recall
    • Heavy duty red HiFlex cables with billet AN connectors
    • 4 LMF™ swirl finished 15" x 15" low profile pads
    • 1500 lb. per pad capacity, 6000 lb. total
    • 2-year limited warranty
    • Includes FREE scale pad box

    Instructions (PDF)

  • King Chrome GM One Wire Alternator, 100 Amp
    King Chrome GM One Wire Alternator, 100 Amp
    x
                

    Streamline engine compartment by eliminating excess wires with this 1-wire alternator.  It fit most GM applications and feature a beautiful chrome plated finish.  This one wire alternator simply needs hook up direct to the main battery lead or power source. The internal regulator picks up the available current and kicks the alternator into the charge mode at pre set voltage.

    • 100 amp, one-wire
    • Chrome plated finish
    • Quick, easy hook-up with supplied instructions
    • Attaches to all popular GM alternator brackets
  • Flathead Lifter Wrench
    $9.99
    Product Rating: 4.25 Stars
    Flathead Lifter Wrench
    x
                

    Use this handy wrench to set your flathead's adjustable lifters.  For use with our 450-F8502 lifters.

  • Rubber GM Transmission Cushion
    Rubber GM Transmission Cushion
    x
                

    OEM-style rubber transmission cushion for many '58-'82 GM transmissions including TH350 auto, Muncie, Saginaw, and others.

    • Meets or exceeds OEM specifications 
    • Rubber formulation provides abrasion resistance and aging stability
    • Tough, hardened steel plate & inserts
    • Chemlock® bonding agent ensures superior rubber-to-metal bond
  • Speedway Dry Erase Marker Board, 17-1/2 Inch x 19-1/2 Inch
    Speedway Dry Erase Marker Board, 17-1/2 Inch x 19-1/2 Inch
    x
                These dry erase boards are great for making notes at the track or  in the garage.  Their convenient 17-1/2" x 19-1/2" size make them easy  to transport. 
    • Stamped aluminum
    • 17-1/2" tall x 19-1/2" wide
  • Speed Fast Stainless Safety Wire, .032 Inch
    Speed Fast Stainless Safety Wire, .032 Inch
    x
                Speed Fast 304 stainless steel safety wire. Sold in one pound rolls and comes with a handy belt clip.
            
  • 9 Inch Ford Viton Pinion Seal
    9 Inch Ford Viton Pinion Seal
    x
                

    These Viton 9" Ford rear axle pinion seals are good to over 400° F. Stock rubber seal starts to deteriorate at about 250° F.

  • Performance Tool W54220 Grease Suction Gun
    Performance Tool W54220 Grease Suction Gun
    x
                Great for filling or emptying rear ends and trannys.  You shouldn't be without one!
            
  • Three-Bolt Carb Base Gasket
    $1.99
    Three-Bolt Carb Base Gasket
    x
                Three bolt carburetor base gaskets fit Stromberg 97-style carbs and Holley 94-style carbs.
            
  • Chevy Front Timing Cover Chrome Bolt Kit
    Chevy Front Timing Cover Chrome Bolt Kit
    x
                Chevy front timing cover chrome bolt kit. 
            
  • Hot Stuff Exhaust Manifold Dressing
    Hot Stuff Exhaust Manifold Dressing
    x
                This space-age blend of stainless steel and ceramic compounds is the ideal coating for cast iron exhaust manifolds! 

    It withstands 2400F° (manifolds rarely exceed 1200°F). Only minimal preparation is required. Easily applied with a small brush or a rag. Coating heat-cures by simply running the engine for 10 minutes. Leaves a durable, raw cast iron appearance.

    A 2 oz. container will do 2-4 manifolds on average.

  • Book - The Official 12 Volt Conversion Guide
    Book - The Official 12 Volt Conversion Guide
    x
                This guide book takes you step by step through the formerly terrifying task of converting your hot rod from 6 volt to 12 volts.   

    Includes the secrets to generator and alternator conversion and hook-up, lighting, gauges, ignition, starters, troubleshooting and more. There's even a cross reference from 6 to 12 volt bulbs.

    Twenty pages. Small easy to handle size 8-1/2" x 5-3/8".

  • Speedway Vega Style Steering Box Combo, All New Assembly
    Speedway Vega Style Steering Box Combo, All New Assembly
    x
                

    Speedway Motors makes it easy to bolt together a cross steering system with our Vega Steering Box Combo kit. Kit includes a Speedway Vega box, steel pitman arm, and a Ford Model T - 1934 frame mount. This steering box accepts a 5/8" 36-spline U-joint or coupler.

    Kit includes:

    • Speedway Vega Steering Box
      • 20:1 steering ratio
      • 5 turns lock-to-lock
    • Steel Vega Pitman Steering Arm
      • Plain finish 
      • Non-offset design
      • Double-tapered "Ford" tie rod end hole (lets you attach the drag link on the top or on the bottom)
    • Vega Steering Box Mount
      • Fits Model T thru 1934 Ford frames
      • Weld-on design
  • Goodridge 15 Inch Braided Brake Line with 90 Degree End
    Goodridge 15 Inch Braided Brake Line with 90 Degree End
    x
                

    These high quality stainless steel, braided fluid lines have a 90° fitting on one end and a straight fitting on the other. They work well for brake lines, clutch lines and gauge lines. These are available with AN3 or AN4 fittings. Sold individually.

    • Stainless steel
    • 90° fitting on one end and a straight fitting on the other
    • Brake lines, clutch lines and gauge lines
    • Available with AN3 or AN4 fittings
    • Sold individually

    Select applicable length. AN size is the "-#" at the end of the part number.

  • Triangular Red Funnel with Fliter
    Triangular Red Funnel with Fliter
    x
                

    Triangular shape funnel allows fast flow. Features large 13" opening and anti-slosh lip. Red only.  With filter.

Goto Previous PagePrevious Page
1 2 3 4 5 ... 25